Inhaltszusammenfassung zur Seite Nr. 1
848-AE0-93A2 (706)
OWNER/OPERATOR MANUAL
PORTABLE GAS DRILL
EDG2300
(NOTE: Drill is optional part.)
Thank you for purchasing a RedMax
WARNING
product.
The engine exhaust from this product Before using our portable gas drill,
contains chemicals known to the State
please read this manual carefully to
of California to cause cancer, birth
understand the proper use of your unit.
defects or other reproductive harm.
APPLICABLE SERIAL NUMBERS : 901112 and up
Inhaltszusammenfassung zur Seite Nr. 2
Read this manual carefully to understand all safety precautions, controls, proper operation and maintenance of your RedMax portable gas drill. Failure to do so could result in serious injury. SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS SAFETY PRECAUTIONS .................................................................................. 4 IN ORDER TO ENSURE PROPER AND SAFE OPERATION OF YOUR PORTABLE GAS DRILL WORK GEAR AND CLOTHING WARNINGS CONSIDERING HANDLING OF FUEL THINGS TO CHECK BEFORE USING YOUR PORTABLE GAS DRILL THINGS TO CHECK BEFORE STARTING UP THE ENGINE AVOID NOISE PROBLEM THINGS TO BE CAREFUL ABOUT WHEN USING YOUR PORTABLE GAS DRILL NOTES ON CARE AND MAINTENANCE OF YOUR PORTABLE GAS DRILL EMISSION CONTROL
Inhaltszusammenfassung zur Seite Nr. 4
Safety Precautions ■ IN ORDER TO ENSURE PROPER AND SAFE • Avoid running the engine indoors. The OPERATION OF YOUR PORTABLE GAS DRILL exhaust gases contain harmful carbon monoxide. • Read this Owner/Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury. • Never use your portable gas drill under circumstances like those described below: 1. When the ground is slippery or when other conditions exist whic
Inhaltszusammenfassung zur Seite Nr. 5
Safety Precautions ■ WORK GEAR AND CLOTHING ■ WARNINGS CONSIDERING HANDLING OF FUEL • When using your portable gas drill, always be sure to wear strong, durable, work • The engine of the portable gas drill is clothing; shirts should be long-sleeved designed to run on a mixed fuel which shirts and pants should be full-length contains highly flammable gasoline. This pants reaching down to the ankles. fuel is highly flammable and you should never store cans of fuel or refill the tank of • Always
Inhaltszusammenfassung zur Seite Nr. 6
Safety Precautions ■ THINGS TO CHECK BEFORE USING ■THINGS TO CHECK BEFORE YOUR PORTABLE GAS DRILL STARTING UP THE ENGINE • Before beginning work, look around • Take a careful look around to make sure carefully to get a feel for the shape of the that no obstacles exist within a perimeter land, and whether or not there are any of 15feet (5m)or less around the portable obstacles which might get in the way while gas drill before starting the engine. working, and remove any obstacles which can be cle
Inhaltszusammenfassung zur Seite Nr. 7
Safety Precautions ■ THINGS TO BE CAREFUL ABOUT WHEN •Never touch the muffler, spark plug, or USING YOUR PORTABLE GAS DRILL other metallic parts of the engine while the •When using your portable gas drill, grip engine is in operation or immediately after the handles of the portable gas drill firmly shutting down the engine. These metallic with both hands, place your feet slightly parts reach high temperatures during apart (slightly further apart than the width operation and doing so could result
Inhaltszusammenfassung zur Seite Nr. 8
Safety Precautions ■ NOTES ON CARE AND MAINTENANCE • Always be sure to turn off the engine OF YOUR PORTABLE GAS DRILL before performing any maintenance or • In order to maintain your portable gas drill checking procedures. in proper working order, perform the •When removing, or reattaching the drills, maintenance and checking operations be sure to wear thick, sturdy gloves and described in this manual at regular use only proper tools and equipment to intervals. In the event that any parts must
Inhaltszusammenfassung zur Seite Nr. 9
Parts Location & Specifications Muffer Spark plug Stop switch Reduction unit Chuck Drill Throttle lever Front grip Rear grip Starter grip Air cleaner Fuel cap MODEL EDG2300 Overall Dimensions (LxWxH) in (mm) 14.7x8.42x9.34 (366x210x233) Dry Weight lbs (kg) 10.6 (4.8kg) Transmission Automatic centrifugal clutch and reduction gears Reduction Ratio 1 : 10.6 Recommended drill size in (mm) Dia. 1/2in.(12.7mm) Engine Type Air cooled 2-cycle gasoline engine Displacement cc (cu. in) 22.5 (1.37) Max. O
Inhaltszusammenfassung zur Seite Nr. 10
Fuel ■ RECOMMENDED MIXING RATIO WARNING GASOLINE 50:OIL 1 • Gasoline is very flammable. Avoid (when using RedMax/ZENOAH smoking or bringing any flame or genuine oil) sparks near fuel. Make sure to stop the 50:1 MIXING CHART engine and allow it cool before GASOLINE gal. 1 2345 refueling the unit. Select outdoor bare 2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13 ground for fueling and move at least 3m (10ft) away from the fueling point GASOLINE liter 1 2345 before starting the engine. 2-CYCLE OI
Inhaltszusammenfassung zur Seite Nr. 11
Fuel 4. Pour In the rest of gasoline and agitate in the engine failing to operate properly. again for at least one minute. As some 5. In the case of storing the product for a oils may be difficult to agitate depending long period of time, clean the fuel tank on oil ingredients, sufficient agitation is after rendering it empty. Next, activate the necessary for the engine to last long. Be engine and empty the carburetor of the careful that, if the agitation is insufficient, composite fuel. there i
Inhaltszusammenfassung zur Seite Nr. 12
Operation ■ THROTTLE CABLE ADJUSTMENT NOTE Check the throttle cable play and adjust to .04 or .08 in. (1~2mm) at the carburetor • The throttle lock makes starting easier. side. Always use it when starting the engine. Throttle cable 5.While firmly holding the auger as .04 or .08 in. illustrated, vigorously pull the starter rope. Adjusting screw (1~2mm) Lock nut ■ STARTING ENGINE 1. When first starting up after putting fuel into the machine, or when re-starting after running out of fuel, push
Inhaltszusammenfassung zur Seite Nr. 13
Operation ■ STOPPING ENGINE ■ ADJUSTMENT OF IDLING SPEED • Release the throttle lever and press on • The engine idling speed is preadjusted at the red button until the engine comes to a the factory so that the engine keeps complete stop. running without moving the drill when releasing the throttle lever to the idling Stop button position. However, due to changes in engine conditions, it may be necessary to adjust the idling. • To increase idling, screw idle adjustment screw in, until preferred
Inhaltszusammenfassung zur Seite Nr. 14
Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. ■ MAINTENANCE CHART every every every 25 50 100 system/compornent procedure before hours hours hours note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ■ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED (p.13) if necessary clea
Inhaltszusammenfassung zur Seite Nr. 15
Maintenance • Check and clean the spark plug. Adjust the electrode gap to .024~.028in (0.6~0.7mm) if necessary. .024 ~ .028 in (0.6~0.7mm) Replacement plug: NGK BPMR7A ■ INSPECTION EVERY 100 HOURS • The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet. In the State of California it is required by law (Section 4442 of the California Public Resources Code) to equip a spark arrester when a gas powered tool is used in any forest covered, bru
Inhaltszusammenfassung zur Seite Nr. 16
Storage ■ BEFORE LONG-TERM STORAGE • Drain fuel tank and run engine out until all fuel in the carburetor is used up. • Remove the spark plug and drop a spoonful 2 cycle oil into the cylinder. Crank the engine several times and replace the plug. Pull starter until compression is felt. • Brush off dirt from the drill surface and apply rust protective oil. •Store the machine in a dry, dust-free place. Disposal • When disposing your machine, fuel or oil for the machine, be sure to allow your l
Inhaltszusammenfassung zur Seite Nr. 17
Parts List PORTABLE GAS DRILL EDG2300 NOTE : 1. Use RedMax/ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. RedMax/ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model name and the serial number are applicable to those specified in the parts list, then use parts number described in the parts list. 4. Th
Inhaltszusammenfassung zur Seite Nr. 18
Parts List : EDG2300 Fig.1 DRIVE UNIT and TOOLS (S/N 901112 and up) 18
Inhaltszusammenfassung zur Seite Nr. 19
EDG2300 Fig.1 DRIVE UNIT and TOOLS (S/N 901112 and up) Key# Part Number Description Q'ty Key# Part Number Description Q'ty 1 3871-21100 Right handle comp. 1 2 3871-21120 • Grip 1 3 3871-21320 Stay 1 4 3545-14240 Bolt 1 5 01641-21423 Washer 1 6 3524-14400 Lever, Throttle 1 7 0280-10504 Nut 1 8 01601-20513 Washer 1 9 0263-30516 Screw 2 10 0280-10504 Nut 2 11 3872-21510 Bracket, Right 1 12 3871-21200 Left handle comp. 1 13 3541-14221 • Grip 1 14 3872-21520 Bracket, Left 1 15 0225-30616 Bolt 4 16 0
Inhaltszusammenfassung zur Seite Nr. 20
Parts List : EDG2300 Fig.2 ENGINE UNIT (S/N 901112 and up) 20
