Inhaltszusammenfassung zur Seite Nr. 1
R
E
B
E
W
®
®
GENESIS
GENESIS S SIL ILVER VER– –B B
Gas Grill
Owners Guide
DANGER Liquid Propane Gas
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid
4. If odor continues, keep away from the
®®
appliance and immediately call your
gas supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
WARNING
1. Do not store spare liquid propane
cylinder within 10 feet
Inhaltszusammenfassung zur Seite Nr. 2
DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. WARNINGS Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas le
Inhaltszusammenfassung zur Seite Nr. 3
Warranty Weber-Stephen Products Co. (Weber) hereby warrants There are no other express warrants except as set forth to the ORIGINAL PURCHASER of this Weber Gas Grill herein and any applicable implied warranties of that it will be free of defects in material and merchantability and fitness are limited in duration to the workmanship from the date of purchase as follows: period of coverage of this express written Limited Warranty. Some regions do not allow limitation on how Aluminum Castings, lifet
Inhaltszusammenfassung zur Seite Nr. 4
Contents Danger & Warnings ................................ A-2 Warranty ................................................. A-3 General Instructions ............................... A-5 Exploded View ....................................... A-6 Parts List ................................................ A-9 Assembly Instructions ............................ B-1 Installing Features .................................. C-1 Operating ............................................... D-1 Lighting..........
Inhaltszusammenfassung zur Seite Nr. 5
Storage General Instructions • The gas must be turned OFF at the LP cylinder Your Weber Gas Barbecue is a portable outdoor when the Weber Gas Barbecue is not in use. cooking appliance. With the Weber Gas Barbecue you • When the Weber Gas Barbecue is stored indoors, can grill, barbecue, roast and bake with results that are the gas supply must be disconnected and the LP difficult to duplicate with indoor kitchen appliances. cylinder stored outdoors in a well-ventilated space. The closed lid and Fl
Inhaltszusammenfassung zur Seite Nr. 6
1 Genesis Silver-B LP 2 3 27 28 4 29 5 6 7 30 31 8 32 33 9 34 35 10 36 37 11 12 38 13 39 14 40 41 15 42 43 16 44 17 32 18 45 46 19 47 20 48 21 49 22 50 23 51 24 52 25 26 53 54 A-6
Inhaltszusammenfassung zur Seite Nr. 7
1. Hinge Pin 27. Hair Pin Cotter 2. Left Endcap 28. Right Endcap 3. Shroud 29. Thermometer 4. Handle 30. Burner Control Knob 5. Warm-Up Basket 31. Control Panel 6. Warming Rack 32. Control Panel Hardware 7. Cooking Grate 33. Ignitor Button 8. Flavorizer Bar 34. Crossover Tube 9. Cooking Box 35. Front and Back Burners 10. 1/4-20 keps nut 36. Center Burner 11. Slide Out Bottom Tray 37. Manifold Hardware 12. Catch pan holder 38. Manifold, Hose and regulator (assembled) 13. 1/4-20 x 1/2 inch bolt 39
Inhaltszusammenfassung zur Seite Nr. 8
© 1999 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks ® of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A. A-8
Inhaltszusammenfassung zur Seite Nr. 9
® ® ® ® ® You will need: Left Frame - 1 Screwdriver Phillips screwdriver Right Frame - 1 Hammer Wheel Frame - 1 7/16 open-end or an adjustable wrench Caster Frame - 1 Pliers Frame Connectors - 2 Block of wood Left Trim - 1 Lid - 1 Right Trim - 1 Work Surface - 1 Cooking Box - 1 Left-Hand Swing-Up Work Surface - 1 Right-Hand Swing-Up Work Surface - 1 Hinge Rods - 2 Cooking grates - 2 Bottom Shelf - 1 Control panel - 1 A-9
Inhaltszusammenfassung zur Seite Nr. 10
Warming Rack - 1 Fuel Guage - 1 Warm-Up Basket - 1 Burner Control Knobs - 3 Flavorizer Bars - 5 Hinge Pins (1/4-20 x 1 1/2 inch clevis pin) - 2 Cylinder Panel - 1 2 inch bolts (1/4-20 x 2 inch bolts) - 5 Bottom tray - 1 1 3/4 inch bolts (1/4-20 x 1 3/4 inch bolts) - 2 Catch Pan Holder - 1 1/2 inch bolts (1/4-20 x 1/2 inch bolts) - 9 Catch-Pan - 1 Keps Nut (1/4-20 Keps Nut) - 1 Disposable Drip Pans - 2 Nylon Washers - 16 Hair Pin Cotter - 2 Manifold Support Bracket - 1 Hubcaps - 3 Thermometer - 1
Inhaltszusammenfassung zur Seite Nr. 11
R E B E W Assembly Instructions Assemble wheel frame Assemble frame You will need: axle rod, two wheel hubcaps, two You will need: left frame, right frame, two 1/2 inch wheels, wheel frame, hammer and a block of wood. bolts, two nylon washers and a 7/16 inch or adjustable Place one end of the axle rod on the block of wood (or wrench. other protected surface). Tap one hubcap onto the end Note - Work on carpeted area (on grass or one of the of the axle rod. Slide one wheel onto the axle, WEBER box
Inhaltszusammenfassung zur Seite Nr. 12
Continue frame assembly Complete frame assembly You will need: caster frame, wheel frame, four 1/2 inch You will need: partial frame assembly, two frame bolts, four nylon washers and a 7/16 inch or adjustable connectors, four 2 inch bolts, four nylon wrench. washers and a 7/16 inch or adjustable wrench. Place the caster frame onto the tabs of the left frame, Hold one frame connector between the caster frame so that the swing table locking latch (1) is to the rear. and wheel frame. Add the nylon
Inhaltszusammenfassung zur Seite Nr. 13
Insert casters You will need: frame assembly and two casters. Slide the cooking box (assembly) to the left within the Push the casters firmly into the inserts in the ends of frame assembly. Add the nylon washer to the bolt. the caster frame. Insert the bolt through the frame and cooking box with the head of the bolt outside the box. Add the keps nut. Tighten by holding the bolt with pliers while you tighten the nut with a wrench. Your Weber Gas Grill manifold assembly, consisting of Add cooking
Inhaltszusammenfassung zur Seite Nr. 14
Install manifold bracket Install cylinder panel You will need: manifold bracket. You will need: Cylinder panel, two 1 3/4inch bolts, two Hook the bracket(2) onto the manifold at the center nylon cylinder glides, two nylon washers a 7/16 inch or burner valve. Place your hand underneath the bracket. adjustable wrench and pliers. Lift the manifold, bracket and cooking box slightly, then Insert the cylinder panel tabs(1) into the slots in the hook the tab of the bracket onto the frame brace(1). fram
Inhaltszusammenfassung zur Seite Nr. 15
Add fuel gauge 3) Tighten the igniter lock nut back onto the igniter. You will need: fuel gauge, two wing nuts and two nylon Note - If the igniter works loose, carefully tighten the washers. igniter lock nut with an adjustable wrench or pliers. 1) Slip the bolts on the back of the fuel gauge through the two small holes in the cylinder panel. (1) 2) Add washers to the bolts, then wing nuts, and tighten with your fingers. (2) (1) (2) (3) Install igniter Note - The igniter wires are already attache
Inhaltszusammenfassung zur Seite Nr. 16
Fill liquid propane cylinder Important LP Cylinder Information Note - The liquid propane cylinder manufacturer is Failure to follow these DANGER statements exactly responsible for the materials, workmanship and may result in a fire causing death or serious injury. performance of the cylinder. If the cylinder has a DANGER defect, malfunctions, or you have a question regarding NEVER store a spare LP Cylinder under or near the cylinder, call the cylinder manufacturer’s customer this barbecue. ser
Inhaltszusammenfassung zur Seite Nr. 17
Check that all burner valves are off Remove plastic dust cover from the fuel cylinder valve. You will need: burner control knobs. Screw the regulator coupling onto the cylinder Valves are shipped in the OFF position, but you should valve(1), clockwise, or to the right. Hand tighten only. check to be sure that they are turned OFF. Put the Note: This is a new type of connection. It tightens knob on each valve. Check by pushing down and clockwise and will not allow gas to flow unless the turning cl
Inhaltszusammenfassung zur Seite Nr. 18
Check: Check for gas leaks 1) Hose to manifold connection. DANGER WARNING: If there is a leak a connection(1), Do not use an open flame to check for retighten the fitting with a wrench and recheck for gas leaks. Be sure there are no sparks or leaks with soap and water solution. open flames in the area while you check If a leak persists after retightening the fitting, turn OFF the gas. DO NOT OPERATE THE BARBECUE. for leaks. Sparks or open flames will Contact the Customer Service Representati
Inhaltszusammenfassung zur Seite Nr. 19
Install the slide out bottom tray Install Lid You will need: the slide out bottom tray(1), catch pan You will need: lid, two hair pin cotters(1) and two hinge holder(2), catch pan and one disposable drip pan. pins(2). Place lid on top of the cooking box. Align the hinges at the rear of the barbecue. Insert hinge pins through the hinges from the outside. Insert hair pin cotters into the small holes in the hinge pins. (1) (1) (2) (2) Hook the ends of the catch pan holder into the hole in the slide
Inhaltszusammenfassung zur Seite Nr. 20
Installing Features Install the right end trim piece with tool holders 3.) Insert one end of the swing-up work surface rod and right swing-up work surface into the hole in the frame. You will need: Right trim piece with tool holders, right swing-up work surface, swing-up work surface rod, one 1/2 inch bolt, one nylon washer and a wrench 1.) Start the right end trim piece into the frame as shown, do not push the trim piece in all of the way and do not add bolt yet. (1) 2.) Slide the swing-up work
