Inhaltszusammenfassung zur Seite Nr. 1
3400 Series
LP Gas Barbecue
Step-By-Step Instructions
FOR YOUR SAFETY
WARNING: Follow all leak check
1. Do not store or use gasoline or other
procedures carefully in this manual prior
flammable vapors and liquids in the
to barbecue operation. Do this even
vicinity of this or any other appliance.
though the barbecue is assembled.
2. An LP tank not connected for use shall
NOTICE TO INSTALLER: These
not be stored in the vicin
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Step 2 Assembly Remove packaged parts Supplies needed Remove and unpackage glass door assemblies, You will need a soap and water solution to check for gas warming rack, Weber Warm-Up Basket, 2 cooking leaks. (See Step "Check for gas leaks.") grates, corrugated box (which contains cookbook and Refer to exploded view if replacement parts are needed. warranty card), 8 short stainless steel Flavorizer Bars and 5 long stainless steel Flavorizer Bars. Figure 2. Your LP tank is shipped empty for safety
Inhaltszusammenfassung zur Seite Nr. 4
Step 3 Step 4 Reinstallation of Stainless Steel Flavorizer Installation of catch pan holder into bottom tray Bars, Cooking Grates and Warming Rack Pull out bottom tray from cooking box. Remove packaging material from bottom tray, catch pan Set the long stainless steel Flavorizer bars side to side holder, catch pan, and drip pan. in the lower position of the cooking box, then set the short stainless steel Flavorizer bars, front to back in the upper position. Figure 4. Bottom tray Figure 7 Hook t
Inhaltszusammenfassung zur Seite Nr. 5
E F Step 5 Step 6 Removal of LP Tank Remove grill from lower packaging Note - You must remove tank and it's packaging before mWARNING: Lifting the barbecue from the lower lifting grill out of lower carton. packaging requires at least two people. 1) Loosen tank lock wing nut and turn tank lock up out With two people lift straight up and over lower of the way. Tighten wing nut. Figure 9 (a). packaging and cardboard support. 2) Lift tank straight up. The cardboard sleeve will come with it, then re
Inhaltszusammenfassung zur Seite Nr. 6
E E F F E F Step 7 Step 9 Install Lid Set LP fuel scale Remove hinge pins and hair pin cotters from back of You will need: LP tank (empty). cooking box. Note - For accuracy, the fuel scale must be set with an Set the lid in place. Align the hinges at the rear of the empty tank. barbecue. Insert hinge pins from the outside. Insert hair We utilize various LP tank manufacturers. Some of the pin cotters into the small holes in the hinge pins. tanks we receive have differing top collar assemblies. F
Inhaltszusammenfassung zur Seite Nr. 7
Step 10 Step 11 Fill LP tank Remove control panel Note - The LP tank manufacturer is responsible for the Pull the right hand swing table up. Stand to the right materials, workmanship and performance of the tank. If side of the barbecue. Slightly pull back both side the tank has a defect, malfunctions, or you have a burner locks. Slide the side burner out from the control question regarding the tank, call the tank manufacturer's panel. Figure 14. Do not disconnect the hose. customer service cen
Inhaltszusammenfassung zur Seite Nr. 8
Remove the burner control knobs. Figure 15 (a). While Check that the igniter is secure in the frame brace and standing at the right end of the barbecue, grasp the has not shifted out of the key hole. Figure 17. under the edge of the control panel at the control panel If it is loose, slide the igniter into the rear of the key hole. push-in buttons and slide along the frame toward you. Carefully tighten the igniter lock nut with an adjustable Figure 15 (b). Lift off the control panel. wrench or pl
Inhaltszusammenfassung zur Seite Nr. 9
E F Check that the tank panel tabs are in their slots in the Remove the tape from the hose and regulator. frame brace. Figure 18. Route the hose so it will not interfere with the scale indicator rod. Tank panel tabs The hose and regulator are connected in the following manner: Slide back the collar of the quick disconnect on the tank valve. Push the male fitting of the regulator into the quick disconnect, and maintain pressure. Slide the collar closed. Figure 21 (a). Figure 21 (b) shows the qui
Inhaltszusammenfassung zur Seite Nr. 10
E E F F Step 14 mWARNING: Do not ignite burners while leak checking. Check for gas leaks Check for leaks by wetting the connections with the soap and water solution and watching for bubbles. If m DANGER m bubbles form or if a bubble grows there is a leak. Do not use an open flame to check for Check: gas leaks. Be sure there are no sparks or a) Hose to manifold connection. Figure 24 (a). open flames in the area while you check b) Regulator to tank connection. Figure 24 (b). for leaks. This will
Inhaltszusammenfassung zur Seite Nr. 11
Step 15 Step 16 Install glass doors Put the control panel back on You will need: one LH glass door assembly and two RH Set the control panel in place over both frame braces. glass door assemblies. (Hold the Crossover Ignition button up while setting the control panel in place.) Place your thumbs over the Start with the LH door assembly. Insert the long hinge control panel push-in buttons, and push them into the pin at the top of the door into the plastic bushing in the underside of the left fra
Inhaltszusammenfassung zur Seite Nr. 12
B E W R E ® ® ® ® ® ® ® ® RH RH LH 1 43 44 45 2 3 46 4 47 5 48 6 49 50 51 52 7 53 54 8 55 9 2 10 56 11 2 57 12 2 13 14 58 15-16 59 17 60 18-20 61-64 65-66 21 22 13 23 14 24 25 26 27 67 68 28 39 42 29 30 31 32 33 34 35 36 37 38 38 40 41 12 B 1 3 E W R E
Inhaltszusammenfassung zur Seite Nr. 13
Parts List Contact: Weber-Stephen Products Company All items are single quantities unless otherwise Customer Service Center specified. 250 South Hicks Road Parts can be ordered directly from Weber-Stephen Palatine, IL 60067-6241 Products Company by phone or mail. (800) 446-1071 Note - Do not return parts to Weber-Stephen Products Co. without first contacting the Customer Service Center by phone or mail. Returning the part may not be necessary. 37 1/4-20 hex nut 1 Lid (assembly) 38 Side burner
Inhaltszusammenfassung zur Seite Nr. 14
Inhaltszusammenfassung zur Seite Nr. 15
Inhaltszusammenfassung zur Seite Nr. 16
A FINAL WORD OF THANKS hank you for choosing a Weber Barbecue. T Our family here at Weber has worked hard to produce the highest quality products for your satisfaction. While we give much attention to our products, an occasional error may occur. Our knowledgeable Customer Service staff is prepared to help you with any problems with parts or assembly. Call our toll free number 1-800-446-1071. For quicker service, please have your owner’s manual available for reference. We also welcome any com
