Inhaltszusammenfassung zur Seite Nr. 1
R
E
B
E
W
®
®
GENESIS
GENESIS S SIL ILVER VER– –B B
Gas Grill
Owners Guide
m DANGER
If you smell gas:
1. Shut off gas to the appliance.
Natural Gas
2. Extinguish any open flames.
3. Open lid
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
®®
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
m WARNING
Do not store or use gasoline or other
flammable liquids or vapors wi
Inhaltszusammenfassung zur Seite Nr. 2
m DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. m WARNINGS m Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. m Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. m After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas le
Inhaltszusammenfassung zur Seite Nr. 3
Warranty Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Grill There are no other express warrants except as set forth that it will be free of defects in material and herein and any applicable implied warranties of workmanship from the date of purchase as follows: merchantability and fitness are limited in duration to the period of coverage of this express written Limited Aluminum Castings, lifetime, 1 year paint Warranty. Some regions do not allow
Inhaltszusammenfassung zur Seite Nr. 4
Contents Danger & Warnings ................................ A-2 Warranty ................................................. A-3 General Instructions ............................... A-5 Exploded View ........................................ A-6 Parts List ................................................ A-9 Assembly Instructions ............................ B-1 Installing Features .................................. C-1 Operating ............................................... D-1 Lighting.........
Inhaltszusammenfassung zur Seite Nr. 5
Storage General Instructions • The gas must be turned OFF at the natural gas Your Weber Gas Barbecue is a portable outdoor supply when the Weber Gas Barbecue is not in cooking appliance. With the Weber Gas Barbecue you use. can grill, barbecue, roast and bake with results that are • When the Weber Gas Barbecue is stored indoors, difficult to duplicate with indoor kitchen appliances. The the gas supply must be disconnected. closed lid and Flavorizer® Bars produce that “outdoor” flavor in the food
Inhaltszusammenfassung zur Seite Nr. 6
1 Genesis Silver-B NG 2 26 3 27 4 28 5 6 7 29 8 30 31 32 9 33 34 35 10 36 11 37 12 38 39 13 40 14 41 15 42 16 43 32 17 44 16 18 45 19 20 46 21 22 47 23 48 24 49 25 A-6
Inhaltszusammenfassung zur Seite Nr. 7
1. Hinge Pin 26. Hair Pin Cotter 2. Left Endcap 27. Thermometer 3. Shroud 28. Right Endcap 4. Handle 29. Burner Control Knob 5. Warm-Up Baskets 30. Control Panel 6. Warming Rack 31. Ignitor Button 7. Cooking Grate 32. Control Panel Hardware 8. Flavorizer Bar 33. Crossover tube 9. Cooking Box 34. Front and Back Burners 10. 1/4-20 keps nut 35. Center Burner 11. Slide Out Bottom Tray 36. Spider Stopper Guard 12. Catch pan holder 37. Manifold Hardware 13. Left Trim Piece 38. Manifold 14. Work Surfac
Inhaltszusammenfassung zur Seite Nr. 8
© 1999 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks ® of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A. A-8
Inhaltszusammenfassung zur Seite Nr. 9
® ® ® ® ® Screwdriver Left Frame - 1 Phillips screwdriver Hammer Right Frame -1 7/16 open-end or an adjustable wrench Wheel Frame - 1 Pliers Caster Frame - 1 Block of wood Lid -1 Frame Connectors - 2 Left Trim Piece - 1 Right Trim Piece - 1 Cooking Box - 1 Work Surface - 1 Left Swing-Up Work Surface - 1 Cooking grates - 2 Right Swing-Up Work Surface Hinge Rod - 2 Control panel - 1 Bottom Shelf - 1 A-9
Inhaltszusammenfassung zur Seite Nr. 10
Warming Rack - 1 Manifold Support Bracket - 1 Warm-Up Basket - 2 Burner Control Knobs - 3 Flavorizer Bars - 5 Hinge Pins (1/4-20 x 1 1/2 inch clevis pin) - 2 2 inch bolts (1/4-20 x 2 inch bolts) - 5 Bottom tray - 1 1/2 inch bolts (1/4-20 x 1/2 inch bolts) - 9 Catch Pan Holder - 1 Keps Nut (1/4-20 Keps Nut) - 1 Catch Pan -1 1/4 Inch Nylon Washers - 14 Disposable Drip Pans - 2 Cotter Pin - 2 Thermometer -1 Hubcaps - 3 Casters - 2 Control Panel Hardware (Phillips screws/washers) - 2 Wheels - 2 Hose
Inhaltszusammenfassung zur Seite Nr. 11
R E B E W Assembly Instructions Assemble wheel frame Assemble frame You will need: axle rod, two wheel hubcaps, two You will need: left frame, right frame, two 1/2 inch wheels, wheel frame, hammer and a block of wood. bolts, two nylon washers and a 7/16 inch or adjustable Place one end of the axle rod on the block of wood (or wrench. other protected surface). Tap one hubcap onto the end Note - Work on carpeted area (on grass or one of the of the axle rod. Slide one wheel onto the axle, WEBER box
Inhaltszusammenfassung zur Seite Nr. 12
Continue frame assembly Complete frame assembly You will need: caster frame, wheel frame, four 1/2 inch You will need: partial frame assembly, two frame bolts, four nylon washers and a 7/16 inch or adjustable connectors, four 2 inch bolts, four nylon wrench. washers and a 7/16 inch or adjustable wrench. Place the caster frame onto the tabs of the left frame, Hold one frame connector between the caster frame so that the swing table locking latch (1) is to the rear. and wheel frame. Add the nylon
Inhaltszusammenfassung zur Seite Nr. 13
Insert casters Add cooking box (assembly) You will need: frame assembly and two casters. You will need: frame assembly, cooking box Push the casters firmly into the inserts in the ends of (assembly), 2 inch bolt, nylon washer, keps nut, pliers the caster frame. and a 7/16 inch or adjustable wrench. Place the cooking box (assembly) in the frame assembly so the burner tubes(1) are under the frame brace(2). (1) (2) Slide the cooking box (assembly) to the left within the frame assembly. Add the nylo
Inhaltszusammenfassung zur Seite Nr. 14
Your Weber Gas Grill Manifold assembly consisting of Install manifold bracket gas manifold, valves and gas burners has been factory You will need: manifold bracket. assembled, pressure- and flame- tested. As a safety Hook the bracket(2) onto the manifold at the center precaution, we recommend you check the burner burner valve. Place your hand underneath the bracket. alignment: Lift the manifold, bracket and cooking box slightly, then 1) Are the ends of the burners under the washers at hook the t
Inhaltszusammenfassung zur Seite Nr. 15
Install igniter The wire holder (1) is to keep ignition wires from Note - The igniter wires are already attached to the interfering with the swing-up table’s bracket. If the wire Gas Catcher Ignition Chamber and the igniter. This holder becomes loose, reinstall or replace it was done to factory test the ignition system. immediately. The igniter lock nut is on the igniter. 1) Loosen the igniter lock nut. 2) Insert the top of the igniter up through the large part of the keyhole in the frame brace.
Inhaltszusammenfassung zur Seite Nr. 16
Install Gas Supply Gas Line Piping General Specifications for Piping n If the length of the line required does not exceed 50 Note - Contact your local municipality for building feet, use a 5/8" O.D. tube. One size larger should be codes regulating outdoor gas barbecue used for lengths greater than 50 feet. installations. In absence of Local Codes, you must n Gas piping may be copper tubing, type K or L; confirm to the latest edition of ANSI Z223.1. WE polyethylene plastic tube, with a minimum wa
Inhaltszusammenfassung zur Seite Nr. 17
Check that all burner valves are off Connect flexible hose to manifold You will need: burner control knobs. You will need: the 12 foot natural supply hose and a Valves are shipped in the OFF position, but you should 3/4 inch wrench. check to be sure that they are turned OFF. Put the Thread fitting end of hose onto manifold. Tighten with knob on each valve. Check by pushing down and wrench. turning clockwise. If they do not turn, they are off. Proceed to the next step. If they do turn continue tu
Inhaltszusammenfassung zur Seite Nr. 18
Check for gas leaks Check: m DANGER 1) Hose to manifold connection. Do not use an open flame to check for gas leaks. m WARNING: If there is a leak a connection(1), Be sure there are no sparks or open flames in the retighten the fitting with a wrench and recheck for area while you check for leaks. Sparks or open leaks with soap and water solution. flames will result in a fire or explosion which can If a leak persists after retightening the fitting, turn cause serious bodily injury or death and da
Inhaltszusammenfassung zur Seite Nr. 19
Install the slide out bottom tray Slide the bottom tray onto the mounting rails under the You will need: the slide out bottom tray(1), catch pan cooking box with finger grip toward you(1). holder(2), catch pan and one disposable drip pan. m WARNING: Do not line bottom tray with aluminum foil. It can cause grease fires by trapping the grease and not allowing grease to flow into the catch pan. (1) (2) Hook the ends of the catch pan holder into the hole in (1) the slide out bottom tray. The front o
Inhaltszusammenfassung zur Seite Nr. 20
Installing Features Install the right end trim piece with tool holders 3.) Insert one end of the swing-up work surface rod and right swing-up work surface into the hole in the frame. You will need: Right trim piece with tool holders, right swing-up work surface, swing-up work surface rod, one 1/2 inch bolt, one nylon washer and a wrench 1.) Start the right end trim piece into the frame as shown, do not push the trim piece in all of the way and do not add bolt yet. (1) 2.) Slide the swing-up work
