Inhaltszusammenfassung zur Seite Nr. 1
Owner's Manual
E L I T E
,®
Liquid Propane Gas Grill
Model 141.16680
Natural Gas Grill
Model 141.17680
WARNING:
Note to Installer: Leave this Owner's Manual
Read this Owner's Manual carefully and be sure with the consumer after delivery and/or installation.
your gas grill is properly assembled, installed and
Note to Consumer: Leave this Owner's Manual
maintained. Failure to follow these instructions
in a convenient place for future reference.
could result in serious bodily injury and/or property
Inhaltszusammenfassung zur Seite Nr. 2
/_ WARNING Warranty ..................................................... 2 Combustion byproducts produced when using Safety Instructions ..................................... 2 this product contain chemicals known to the State of California to cause cancer, birth Hardware ............................................................ 6 defects, or other reproductive harm. Parts Diagram and Lists ........................ 7 WARNING Assembly Instructions ............................... 10 Failure to
Inhaltszusammenfassung zur Seite Nr. 3
18-1/2incheshighis the maximum sizeLPgas • LP gas tanks must be stored outdoors in a well-ventilated area and out of the reach of tankto use. You must use an "OPD" gas tank which offers an Overfill Prevention Device. children. Disconnected LP gas tanks must not This safety feature prevents the tank from being be stored in a building, garage or any other overfilled which can cause malfunction of the LP enclosed area. gas tank, regulator and/or grill. • When your gas grill is not in use the gas mu
Inhaltszusammenfassung zur Seite Nr. 4
Figure 1 (Natural gas model only) IMPORTANT: your Kenmore Natural Gas Grill cannot GAS SUPPLY be converted to use LP Gas. Attempting to do so INSIDE is extremely hazardous and will also void the grill WALL warranty. OUTSIDE WALL Your natural gas grill is designed to operate on TO GRILL natural gas only, at a pressure of 7" water column SHUT OFF (W.C.) (1/4 psi or 1.75 kpa), regulated at the LOCKING / residential meter. Check with your gas utility company for local gas pressure and with your MALE
Inhaltszusammenfassung zur Seite Nr. 5
CAUTION: Spiders and small insects occa- To reduce the chance of "FLASHBACK" (see sionally spin webs or make nests in the grill CAUTION at right) clean the Burner Tubes and Burner Tubes during transit and warehousing. Burners before fully assembling your grill. Remove the Cotter Pin from the rear underside These webs can lead to a gas flow obstruc- tion which could result in a fire in and around of each Burner using a pair of long nose pliers. the Burner Tubes. This type of fire is known Careful
Inhaltszusammenfassung zur Seite Nr. 6
Thefollowingtableillustratesa breakdown of the hardwarepack.It highlights what components are used in the various stages of assembly. Ref. Component Qty. Purpose of Components Install Caster To Caster Seats of Bottom Shelf H005 1/4"x1/2" Phillips Head Screw 16 Attaches Cart Side Panels To Bottom Shelf H030 l/4"x50mm Phillips Head Screw 8 H005 Attaches Rear Panel To Cart 1/4"x1/2" Phillips Head Screw 7 H005 Attaches Tank Pull-out Tray Kit To Bottom Shelf 1/4"x1/2" Phillips Head Screw 4 (LPG model
Inhaltszusammenfassung zur Seite Nr. 7
LPG= LiquidPropane Gas NG = Natural Gas 39 \34 40 (LPG only) j(LPG anly)44a NG only)44b x 32 33 38 59 (LPGonly) It II \_° 5O (LPG 43 670(LPG only) _:_'67b(NG only) \ 51 49 53 7
Inhaltszusammenfassung zur Seite Nr. 8
REF# DESCRIPTION PART# QTY 1 1. Stainless Steel Lid PO0116346A 1 2. Stainless Steel Lid Trim Plate P0011434EA 1 3. Lid Side Panel - Left P00105347U PO0106347U 1 4. Lid Side Panel - Right 1 P00601171A 5. Temperature Gauge 1 6. Lid Handle P00205031B 1 7. Name Plate P00410038C PO1506027B 1 8. SIS Secondary Cooking Rack P01606030B 2 9. SIS Stainless Steel Cooking Grid 1 10. S/S Stainless Steel Cooking Grid - 4" Size P01606031B 2 11. SIS Stainless Steel Flame Tamer P01708031B 12. S/S Stainless Steel
Inhaltszusammenfassung zur Seite Nr. 9
REF# DESCRIPTION PART# QTY 44a. Rear Panel (LPG only) P07702010E 1 44b. Rear Panel (NG only) P07702013E 1 45. Door Bracket P03301017J 1 46. Door Panel - Left P04302011A 1 47. Door Panel - Right P04303011A 1 48. Door Trim Plate - Left P07506007D 1 49. Door Trim Plate - Right P07507007D 1 50. Door Axle Bracket - Left Top P03314018C 1 51. Door Axle Bracket - Left Bottom P03314019C 1 52. Door Axle Bracket - Right Top P03314020C 1 53. Door Axle Bracket - Right Bottom P03314021C 1 54. S/S Door Handle
Inhaltszusammenfassung zur Seite Nr. 10
Figure 1 CASTER CAUTION: While it is possible for one person to CASTER / assemble this grill, obtain assistance from another person when handling some of the larger, heavier pieces, especially the grill head. BOTTOM /SHELF / 1. Open Lid of shipping carton and remove top sheet of cardboard. Lay cardboard sheet on floor and use as a work surface to protect floor and grill parts from scratches. 2. Slice all carton corners with a sharp utility knife to lay open the carton panels. This will allow you
Inhaltszusammenfassung zur Seite Nr. 11
Figure 4 (LP gas model only) 5. Place the Tank Pull-out Tray Kit on the Bottom Shelf. Extend the Tank Tray outward from its Bracket so you can align the holes on the Bracket CART SIDE PANEL-LEFT with the threaded holes on the top of Bottom Shelf. TANK PULL-OUT TRAY KIT Tighten securely by using 4 of the 114"x112"Phillips REAR PANEL (LP gas model only) Head Screws provided. See Fig. 4. Slide tray back into Bracket. t I ! 6. Before installing the Door Bracket to the i inside of front Cart Side Pan
Inhaltszusammenfassung zur Seite Nr. 12
Figure 6c 4. Before installing the Door Axle Bracket-left top CART SIDE to the Left Cart Side Panel, with an assistant, DOOR AXLE BRACKET PANEL- LEFT -LEFT TOP hold the Door Panel and keep it vertical. \ " \ 5. Place the axle on top of the Left Door Panel in the Door Axle Bracket-left top. Install the Door Axle Bracket-left top to the Left Cart Side Panel. Align the holes on the Door Axle Bracket-left top with threaded holes on the top of Left Cart Side Panel. Tighten securely by using 2 of the
Inhaltszusammenfassung zur Seite Nr. 13
Installing Manual Lighting Stick Figure 9 . Attach the Manual Lighting Stick to the Left Bowl Support Bracket as shown in Fig. 9. Align the hole at the end of Manual Lighting Stick Wire with the threaded hole on the Left OUTSIDE BOWL PANEL-LEFT Bowl Support Bracket, Tighten securely using the M4x8mm Phillips Head Screw. M4x8rnm PHILLIPS HEAD SCREW _ MANUAL LIGHTING STICK Figure 10 Installing Side Shelf and Cart Side Handle 1. Remove the white protective film from the SIDE SHELF+LEFT stain)ess st
Inhaltszusammenfassung zur Seite Nr. 14
Installing Cooking Components Electrode Check - Requires an Assistant Before placing the cooking components into your Important: Before cooking on your grill the first grill, ensure that the Spark Electrode Tip is properly time, wash the Cooking Grids and Cooking Rack positioned within each Gas Collector Box ( a with warm, soapy water. Rinse and dry thoroughly. 3-1/4" wide stainless mechanism found at the front Season with cooking oil regularly. After cooking is between each set of Burners.) The
Inhaltszusammenfassung zur Seite Nr. 15
Fuel Gauge Display Installation. Figure 14a CARTSIDE IMPORTANT: Before installing batteries be sure the REAR PANEL PANEL-RIGHT gas tank is not mounted in the tank pull-outtray. \ 1. Open thefront Doorsof Cabinet. Pullout the LPG Tank Pull-out Tray. Connect the Wire Plug "A" from Fuel Gauge Display with the Wire Plug "B" from rear of Tank Pull-out Tray. Unscrew 1/4" x 1/2" Phillips head Screw from Rear Panel and install Wire Fastener to Rear Panel. Tighten securely using the same screw. See WIRE
Inhaltszusammenfassung zur Seite Nr. 16
Connecting A Liquid Propane Gas (LP gas) Figure 15a (LP gas model only) Tank To Your Grill 1. Open the front Doors of cabinet. Pull out the LPG Tank Pull-out Tray. Place a 20 Ib tank with foot ring into the hole in the tray, See Fig.15a. Make sure the tank valve is in the OFF positon, 2. Align the tank so the Tank Valve faces the rear right corner of cabinet. Use the 5/ 16"x89mm Wing Bolt to secure gas tank from rear of tray.See Fig. 15a. FRONT DOOR 3. Check the tank valve to ensure it has prope
Inhaltszusammenfassung zur Seite Nr. 17
Connecting Natural Gas To Your Grill WARNING For Natural Gas grills: Connect the hose end of the 12 foot Natural Gas Hose to the Gas Mani- A strong gas smell, or the hissing sound of fold as shown in Fig.15c. Thread the 12 foot gas indicates a serious problem with your gas Natural Gas Hose through the hole of Rear Panel grill or the LP gas tank. Failure to immedi- to outside. Also read the natural gas safety ately follow the steps below could result in a instructions.(on page 4) fire or explosio
Inhaltszusammenfassung zur Seite Nr. 18
8. If the burner does not light, turn the Control Knob to OFF, wait 5 minutes for gas to clear, then retry. Basic Lighting Procedures 9. Once the left grill burner is ignited, the adjacent Machine oils used inthe manufacturing process of burner can be lit by simply turning its Control Knob stainless steel can cause stainless steel to turn a tan to HIGH. color. Before initial grill use, remove protective PVC film from Control Panel and inside and outside of Grill 10. Adjust Control Knobs to your
Inhaltszusammenfassung zur Seite Nr. 19
• Misalignmentoflgnitoron Burner Manually Lighting Your Grill by Match Correction: Check for proper position of the To light your main burners by match, insert a match Electrode Tip as shown in Figure 12 The gap into the Manual Lighting Stick and follow steps 1 between the Spark Electrode Tip and Burner or through 6 of the Gas Lighting Instructions. Then, light Spark Receiver should be approximately 3/16", the match and place Manual Lighting Stick through the Adjust if necessary. With the gas su
Inhaltszusammenfassung zur Seite Nr. 20
5. Cover each Gas Valve Orifice with aluminum foil. 6. Brush the insideand bottom of the grill with a fiber CAUTION: pad or nylon brush, and wash with a mild soap and Be sure your grill is OFF and cool before cleaning. warm water solution. Rinse thoroughly and let dry. Take care not to chip or scratch the painted surfaces because it will void your warranty against rusting. 7. Remove aluminum foil from Orifices and check each Orifice for obstruction. As with all appliances, proper care and mainte
