Inhaltszusammenfassung zur Seite Nr. 1
Use & Care Guide
®
Liquid Propane Gas Grill
Sears Model No: 119.16433010
Safety
Parts
Use and Care
Assembly
Espa_ol, Pg. 30
This Grill is for Outdoor Use Only
Grill Information Center
Missing Parts? Assembly Questions?
Operation Problems? Before
• Read and follow all Safety, Assembly,
returning grill to store,
and Use & Care Instructions in this
call 1-800-933-0527
Guide before assembling and
cooking with this grill.
• Failure to follow all instructions in
Tools needed for assembly:
this Use & C
Inhaltszusammenfassung zur Seite Nr. 2
IF YOU SMELL GAS: Primary Safety Warnings. .................................. 1-3 Shut off gas to the appliance. Warranty Information ............................................ 2 Extinguish any open flame. Pre-Assembly instructions .................................... 3 Open lid. Part Diagram and Lists ...................................... 4-7 If odor continues, keep away Assembly Instructions ..................................... 8-18 from the appliance and immediately Use & Care Instruction
Inhaltszusammenfassung zur Seite Nr. 3
The installation must conform with local codes or, DO NOT light this grill without first reading in the absence of local codes, with either the the Lighting Instructions. National Fuel Gas Code, ANSI Z223.1/NFPA 54, DO NOT light this grill without checking the or CAN/CGA B149.1, Natural Gas and Propane burner tubes for blockage that could have Installation Code, or Propane Storage and occurred during shipment. See the Cleaning Handling Code, B149.2. and Maintenance Instructions. All electrical a
Inhaltszusammenfassung zur Seite Nr. 4
F A Phillips Head Bolt M6×35mm Phillips Head Screwdriver Qty: 4 pcs Qty: 1 pc G lm B Phillips Head Bolt M6x16mm Battery Size AA Qty: 24 pcs Qty: 1 pc H C Phillips Head Bolt M6xl0mm Cabinet Door Stop Qty: 4 pcs Qty: 1 pc D "S" Hook Phillips Head Bolt M4×Smm Qty: 22 pcs Qty: 3 pcs E Plastic Washer M6 Washer M4 Qty: 8 pcs Qty: 4 pcs
Inhaltszusammenfassung zur Seite Nr. 5
Key Qty Part No. Description A1 1 *ASMA0085-01 Hood Assembly A2 2 *ASMA0014-03 Hood Bolt Assembly A3 1 CA0046-001 Hood Handle Seat Assebmly A4 2 FLPP0114 Hood Handle Heat Insulator A5 1 SE0213 Thermometer A6 1 CA0045-002 Thermometer Seat A7 1 *ASMA0014-05 Hood Handle B1 1 *ASMB0085-01 Firebox Assembly B2 1 SC1020 Gas Manifold Assembly B3 1 *ASMB0085-02 Firebox Front Heat Shield B4 1 SD0051 Rotisserie Burner B5 1 *ASMB0085-03 Rotisserie Burner Orifice Support B6 1 SC0097 Rotisserie Burner Orifice
Inhaltszusammenfassung zur Seite Nr. 6
Description Key Qty Part No. C2 1 $7004-042D-001 Side Burner Cover C3 1 $7001-042D-017 Side Burner Outer Frame Assembly C4 1 *ASMD0085-01 Side Burner C5 1 *ASMD0085-02 Side Burner Upper Control Panel C6 1 PLABS0090-001 Control Knob Seat- Large C7 1 PLABS0103-001 Control Knob - Large C8 1 S7005-F00B-026 Side Burner Lower Control Panel C9 1 *ASMC0012-08 Towel Bar Handle C10 1 SE0084-012 Side Burner Cooking Grate Cll 1 *ASMD0085-03 Side Burner Inner Frame C12 1 SE0083 Side Burner Electrode C13 2 SB
Inhaltszusammenfassung zur Seite Nr. 7
_----(
Inhaltszusammenfassung zur Seite Nr. 8
Remove Firebox from Cabinet [] Cut fastening straps on Cabinet Toe Plate. Remove the Toe Plate and set aside. Cut fastening straps securing regulator and hose to cabinet. [] Unscrew and discard the 8 Phillips Head Bolts (M6x35mm) and 8 Washers (M6) from the corner holes of the cabinet. Remove the crossbar and set aside. [] With the aid of an assistant, carefully lift the cabinet up from the firebox and set aside. Remove all foam packing from the Firebox. Raise lid and remove and unpack parts ins
Inhaltszusammenfassung zur Seite Nr. 9
Install Cabinet Toe Plate [] Attach the Cabinet Toe Plate to the Cabinet Bottom Panel using 4 Phillips Head Bolts (M6xl0mm), [] Place cabinet in upright position on casters, Phillips Head Bolt M6xl0mm Qty: 4 Install Cabinet Doors and Cabinet Front Crossbar [] Insert the Cabinet Right Door bottom pin into the Cabinet Bottom Panel (Inset 1), and insert the Cabinet Right Door top pin into the Cabinet Front Crossbar (Inset 2), With door magnets extending into Cabinet, attach the Cabinet Front Crossb
Inhaltszusammenfassung zur Seite Nr. 10
Hang Condiment Basket and attach Cabinet Door Stop [] Attach the Cabinet Door Stop to the front of cabinet bottom using 2 Phillips Head Bolts (M4x8mm), [] Hang Condiment Basket on the inside of Cabinet Right Door, Phillips Head Bolt M4x8mm Qty: 2 Cabinet Door Stop Qty: 1 /. Attach Firebox to Cabinet [] With the aid of an assistant, place the Firebox onto the Cabinet Frame with Regulator Hose and Side Burner Ignition Wire hanging inside of Cabinet, Note: Rear of Firebox rests on two tabs at back
Inhaltszusammenfassung zur Seite Nr. 11
Install Grease Tray [] Insert the Grease Tray along two sides of the Firebox from the back underneath the firebox. Insert tray with the grease drain hole positioned as shown. Be careful when sliding the tray past wires and fuel line. Slide tray fully in until it locks into place behind stops. ............. I, Grease drain hole Install Grease Pan Bracket and Grease Pan [] From the rear of cabinet, insert the Grease Pan Bracket into the bottom of the Grease Tray. [] From the front of Cabinet, inse
Inhaltszusammenfassung zur Seite Nr. 12
Install Side Shelf Upper and Lower Front Panels [] Attach the Side Shelf Upper Front Panel to Side Shelf Frame using 3 Phillips Head Bolts (M4xSmm), [] Attach the Side Shelf Lower Front Panel to Side Shelf Upper Front Panel using 3 Phillips Head Bolts (M4x8mm), Phillips Head Bolt M4x8mm qty: 6 I_l Install Towel Bar Handle, "S" Hooks [] Slide 3 "S" Hooks onto the Towel Bar Handle, Use 2 Phillips Head Bolts (M4x8mm) and 2 Washers (M4) to attach the Towel Bar Handle to the Side Shelf Frame, Note: W
Inhaltszusammenfassung zur Seite Nr. 13
Znstall Side Burner Upper and Lower Control Panels [] Attach the Side Burner Upper Control Panel to Side Burner Frame using 3 Phillips Head Bolts (M4xSmm), [] Attach the Side Burner Lower Control Panel to Side Burner Frame using 3 Phillips Head Bolts (M4xSmm), Phillips Head Bolt M4x8mm qty: 6 Znstall Towel Bar Handle [] Use 2 Phillips Head Bolts (M4x8mm) and 2 Washers (M4) to attach the second Towel Bar Handle to the Side Burner Frame, Phillips Head Bolt M4x8mm qty: 2 Washer IV]4 Qty: 2 13
Inhaltszusammenfassung zur Seite Nr. 14
Install Side Shelf Frame to Firebox [] Unscrew the 2 Phillips Head bolts ¼ inch from the upper left and right corner holes in the right side of the firebox as shown in Inset 1. The bolts extending out of the firebox sides are to attach the side shelf frame. [] Slide the upper holes of the side shelf frame over the heads of the 2 Phillips Head Bolts and drop down. [] Use 2 Phillips Head Bolts (M6x16mm) to attach the lower holes in the side shelf frame to the firebox as shown in Inset 2. [] Use 1
Inhaltszusammenfassung zur Seite Nr. 15
Install Side Burner Frame to Firebox [] Unscrew the 2 Phillips Head bolts 1/4inch from the upper left and right corner holes in the left side of the firebox as shown in Inset 1. The bolts extending out of the firebox sides are to attach the side Burner frame. [] Slide the upper holes of the side Burner frame over the heads of the 2 Phillips Head Bolts and drop down. [] Use 2 Phillips Head Bolts (M6x16mm) to attach the lower holes in the side Burner frame to the firebox as shown in Inset 2. [] Ti
Inhaltszusammenfassung zur Seite Nr. 16
Install Side Burner Valve [] Detach side burner ignition wire from the regulator hose. Feed side burner valve and igniter wire through hole in left side of cabinet. [] Open side burner lid and cut tie wrap securing grate to pan. On underside of pan, remove the 2 screws holding the side burner in place. See Inset 1. [] Secure the side burner valve stem to the Side Burner Lower Control Panel using 2 Phillips Head Bolts (M4x8mm). See Inset 2. [] Center the side burner valve into the side burner tub
Inhaltszusammenfassung zur Seite Nr. 17
Install Heat Diffusers, Cooking Grates, Warming Rack [] Insert the heat diffusers into the firebox by placing them into the indentations in the front and back of the firebox. See Inset 1. [] Place the Cooking Grates into the firebox. The grate bottoms have a small knob on each corner. See Inset 2. [] Insert the warming rack into the top of the firebox. See Inset 3. The raised lip goes towards the back of the firebox. See Inset 3. Inset 1 Inset 3 Inset 2 [] Place Unscrew and Secure the boltLP and
Inhaltszusammenfassung zur Seite Nr. 18
Install Battery [] Unscrew the electronic ignition button. Place the AA Battery into the ignition with the positive (+) end facing out. Screw the electronic ignition button back into place. Battery Size AA Qty: 1 Congratulations - Assembly is now complete! [] Remove any additional labels or packing material from the grill except the CSA label. Be sure to clean all foam packing material out of all areas. [] Read the remaining sections of the Use 8( Care Guide prior to operating your grill. [] To
Inhaltszusammenfassung zur Seite Nr. 19
CORRECT LP GAS TANK USE • Never allow children to operate your grill. Do not allow children or pets to play near your grill. • LP gas grill models are designed for use with a • Use of alcohol or drugs may impair the ability standard 20lb. (9.1kg) Liquid Propane Gas (LP Gas) to assemble and operate the appliance. tank, which is not included with the grill. Never • Keep a fire extinguisher readily accessible. In connect your gas grill to an LP gas tank that the event of an oil or grease fire, do n
Inhaltszusammenfassung zur Seite Nr. 20
Notes about LP Gas Tank Exchange Programs Regulator and LP Cylinder Connections Many retailers that sell grills offer you the option of replacing your empty LP gas tank through an exchange service. Use only those reputable exchange companies that inspect, precision fill, test and certify their tanks. Exchange your tank only for an OPD safety feature equipped tank as described The gas pressure regulator provided with this in the LP gas tank section of this manual. outdoor cooking appliance must b
