Inhaltszusammenfassung zur Seite Nr. 1
®
®
Aussie
by Meco
LP Gas Grill
Assembly and Use Manual
TM
Joey
MODEL 7110.7.641 Liquid Propane Gas Grill
FOR OUTDOOR HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.
For Customer Service, call 1-800-251-7558 or visit our web site at www.meco.net
• Failure to follow these instructions could result in fire or explosion which could cause death,
serious personal injury, or property damage.
• Read and follow instructions carefully before assembly or use.
• Do not use this product for any other purpose
Inhaltszusammenfassung zur Seite Nr. 2
— NOTICE — MECO CORPORATION STRIVES TO BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IF WE OMITTED ANY PARTS NEEDED FOR ASSEMBLY, OR YOU NEED TROUBLESHOOTING INFORMATION, PLEASE CONTACT US USING OUR TOLL FREE NUMBER. THANK YOU FOR PURCHASING A MECO CORPORATION PRODUCT. 1-(800)-251-7558 CONSUMER SERVICE DEPARTMENT 8 am - 5 pm E.S.T Mon. - Fri. MECO CORPORATION 1-(423)-639-1171 (TELEPHONE) 1500 INDUSTRIAL ROAD www.aussiegrill.net 1-(423)-639-2570 (FAX) GREENEVILLE, TN. 37745 USA CONTENTS I. Assemb
Inhaltszusammenfassung zur Seite Nr. 3
PARTS ILLUSTRATIONS If you need replacement parts, refer to the Parts Illustrations and the Parts List to find the exact parts you need. If you have any questions which require help, contact Customer Service and be sure to mention the model number of your grill. (3) Cylinder Retainer Clip (1) Owner’s Manual (4) Left Front Wheel Leg (2) Bottom Shelf (5) Left Rear Wheel Leg (8) Bolt, M5x40mm (7) Right Rear Fixed Leg (6) Right Front Fixed Leg (9) Axle (13) Hood (11) Axle Spring Pin (12) Wheel Cover
Inhaltszusammenfassung zur Seite Nr. 4
(33) Hood Handle (31) Handle Spacer (32) Handle Spacer (Tapered) (Fitted) (35) Flame Diffuser (34) Cooking Grid (36) Main Burner 42) Main Burner Electrode (38) Warming Rack (37) Fabric Panel (39) LP Cylinder (40) Control Panel Heat Shield w/Manifold and Regulator (41) Control Knob 4
Inhaltszusammenfassung zur Seite Nr. 5
To reduce the risk of a cut injury: · Wear protective gloves when handling parts that have sharp edges. · Some assembly may require help from another person. Observe where noted. TOOLS: and/or or STEP 1) Cart Assembly: (3) LP CYLINDER CLIP Attach the Legs to the Bottom Shelf with (8) M5 X 40 BOLT M5 x 40 Bolts threaded into the Bottom 8 PC Shelf holes. Position legs with the holes exactly as indicated . (2) BOTTOM SHELF 1 PC (4) LEFT FRONT (5) LEFT REAR WHEEL LEG WHEEL LEG (6) RIGHT FRONT (7) R
Inhaltszusammenfassung zur Seite Nr. 6
STEP 2) Assemble Axle, Wheels & Wheel Covers: Push Axle through center hole in Wheel and through lower hole in each leg. (FIG. 2A) Insert Axle pin through small hole in end of Axle until it snaps over it. (FIG. 2B) Align Wheel Cover pins with 3-holes in Wheel and push flush against Wheel. (9) AXLE 1 PC (11) AXLE PIN 2 PC (10) WHEEL (12) WHEEL COVER 2 PC 2 PC (10) WHEEL (9) AXLE (12) WHEEL COVER WHEEL LEGS FIG. 2A (11) AXLE PIN FIG. 2B 6
Inhaltszusammenfassung zur Seite Nr. 7
Step 3) Assemble Hood/Bowl to Cart: (16) M6 LOCKNUT 4 PC (15) BOLT, M6X45 4 PC Bowl Bracket Legs (14) HOOD/BOWL ASSEMBLY Control Panel Bolt on each NOTE: REQUIRES 2-PERSONS side of grill · With Cart upright, align Bowl Bracket legs with Cart legs. (FIG. 3A) · Lower Hood/Bowl so ends of Cart legs insert into Bowl Bracket legs. · Press downward until leg screw holes align. NOTE: If cart legs do not align and fit into Bowl Bracket legs easily, loosen the Control Panel bolts slightly. Then o
Inhaltszusammenfassung zur Seite Nr. 8
Step 5) Assemble Sidebraces: · Attach Right and Left Sidebraces (19 & 20) to legs with ST4.0 x 10 Screws. (FIG. 5A) Secure Bottom Heat Shield to Left Sidebrace with M4x10 Bolts and M4 Wingnuts. (FIG. 5B) Allow Heat Shield Edge to overlap Sidebrace edge. (22) BOLT, (21) SCREW, ST4.0 x 10 M4x 10MM 4 PC 2 PC Heat Shield edge over (23) M4 WINGNUT Crossbrace (23) WINGNUT, M4 edge 2 PC (22) BOLT, M4x10MM FIG. 5B (20) Left Sidebrace (21) Screw, ST4.0 x 10 (24) Rear CrossBrace (Pre-assembled) (19) Rig
Inhaltszusammenfassung zur Seite Nr. 9
Step 6) Assemble Side Tables: Align bracket holes of Left and Right Side Tables with holes in Bowl Leg Brackets. Attach Side Tables with M6 x 15 Bolts underneath. (FIG. 6A 7 6B) (25) RIGHT SIDE (26) LEFT SIDE TABLE TABLE (27) BOLT, M6X15 8 PC FIG. 6B (27) SCREW, M6X15 (27) BOLT, M6X15 FIG. 6A Step 7) Attach Hood Handle: Open Hood. Insert the M6 x 50 Bolt through the right side of Heat Shield (right side has one hole), Hood and Handle Spacer and thread into handle. Do not tighten completely.
Inhaltszusammenfassung zur Seite Nr. 10
Step 8) Attach Front Panel: Remove the M6 nut used to attach the upper and lower leg sections. Place the large eyelet over the bolt and replace the nut. (FIG. 8B) Using the ST4.0 Screw, secure the Fabric RIGHT SIDE Panel to holes in the lower legs over the eyelets. (FIG. 8A) (21) SCREW, ST4.0 x 10 (21) SCREW, ST4.0 x 10 4 PC FIG. 8A FIG. 8B (37) FABRIC PANEL Step 9) Install Flame Diffuser: Flame Diffuser mounting stud in Bowl. Place the Flame Diffuser over the Main Bowl Burner, onto the two mou
Inhaltszusammenfassung zur Seite Nr. 11
OPERATING YOUR LP GAS GRILL · Never fill the LP gas cylinder more than 80% of CONNECTING/DISCONNECTING THE GAS cylinder volume. (20 lb. maximum) Do not ask the propane supplier to over-fill the cylinder. USING GAS · If you obtain LP gas through a cylinder exchange dealer, make sure you get a safe and adequate O.P.D. cylinder. (See page 22) Use only a licensed LP gas cylinder dealer. CARBON MONOXIDE HAZARD · Place dust cap on cylinder valve outlet whenever the · This appliance can produce ca
Inhaltszusammenfassung zur Seite Nr. 12
3) Lift and swing LP Cylinder Retainer Clip to outside of grill. Set LP cylinder in the large To avoid pinching in next step, keep fingers hole inside the Bottom Shelf. Rotate the LP and hands near corners of Cylinder Retainer cylinder toward the front of grill so regulator Clip when swinging Clip over cylinder. hose may connect. (FIG. 11A) 6) Swing the Cylinder Retainer Clip over round shoulder of the LP cylinder. Exert pressure at Rotate ends of clip until it stops at the cylinder Cylin
Inhaltszusammenfassung zur Seite Nr. 13
6) Check for leaks by brushing the soap solution SELECTING A LOCATION on all gas valves, hose connections and fittings. (shown by the heavy arrows in (FIG. 12A & 12B) To reduce the risk of serious bodily injury or death: Make sure you generously brush the locations · This outdoor cooking appliance shall be used only with the soap solution, completely surrounding outdoors and shall not be used in a building, garage, the connections and fittings. or any other enclosed area. Locate outdoor
Inhaltszusammenfassung zur Seite Nr. 14
To reduce the risk of serious bodily injury or death: · Open Hood before lighting the grill to prevent an explosion from any gas accumulation. · If lighting attempts fail, or the burners go out during operation, turn all control knobs “Off” to dissipate any accumulation of gas. Accidental ignition could occur. Wait five minutes before repeating lighting procedure. FIG. 13B · Light both left and right sides of burner to prevent gas from accumulating. LIGHTING THE GRILL USING THE IGNITOR 1. O
Inhaltszusammenfassung zur Seite Nr. 15
MANUAL LIGHTING THE GRILL Manual Lighting Hold flame near Burner. To reduce the risk of serious bodily injury or death: · Open Hood before lighting the grill to prevent an explosion from any gas accumulation. · If lighting attempts fail, or the burners go out during operation, turn all control knobs “Off” to dissipate any accumulation of gas. Accidental ignition could occur. Wait five minutes before repeating lighting procedure. FIG. 14B · Light both left and right sides of burner to preven
Inhaltszusammenfassung zur Seite Nr. 16
· Do not attempt to extinguish a grease fire with water WARMING RACK or other liquids. Have an BC fire extinguisher Warming racks are a convenient way to keep cooked food accessible. Do not douse or spray the grill or cooking warm or to warm items such as bread or rolls. When opening surfaces with water when hot. Burns from grease or the hood, be alert of dripping fat from the warming rack which the water splatters could occur. could then drip onto the barbecue causing a mess. Always · If you
Inhaltszusammenfassung zur Seite Nr. 17
CARE AND MAINTENANCE To reduce the risk of a cut injury: SPIDER ALERT! · Be careful or wear protective gloves when cleaning grill Should you notice that your burner(s) are getting hard to light parts that have sharp edges. or the flame is not as hot as it once was, Refer to the “How to Clean your Burners” Section to remove any possible CLEANING THE GRILL obstructions. 1) Remove Drip Cup, Cooking Grid, and Flame Diffuser. Control Panel 2) Drip Cup-Wash the Drip Cup with soap and water. Burner 3
Inhaltszusammenfassung zur Seite Nr. 18
5) Use a pipe cleaner to clear insect nests from the inlet hole of main burner (FIG. 15D). Open up the main burner holes with a small nail or wire.Normal wear and corrosion may enlarge some holes, however, if large cracks or Heat Shield holes are found, replace the Burner. Use a brass wire brush to remove food particles and corrosion from the Heat Shield burner surface. (Note: It is normal for surface rust to be edge over present on the burners.) It can be wire brushed and Crossbrace coat
Inhaltszusammenfassung zur Seite Nr. 19
Gas Leaks and Fire Emergencies Problem Solution Possible Cause Gas leaking from Turn off gas at the LP cylinder. Replace valve/hose/regulator Damaged hose. cracked/cut/burned before continuing use. hose. Gas leaking from LP Replace LP Cylinder Mechanical failure due to rust cylinder or mishandling. Gas leaking from LP Turn off LP cylinder valve. Return cylinder to gas supplier. Failure of valve from mishan- cylinder valve dling or mechanical malfunc- tion. Gas leaking between Turn off LP Cylinde
Inhaltszusammenfassung zur Seite Nr. 20
TROUBLESHOOTING (Cont’d) Problem Possible Cause Solution Burners will not light LP-Excess flow valve tripped Turn control knobs to “off” position and turn LP gas cylinder using the ignitor in regulator. handle clockwise until it stops. Wait five minutes. Relight LP gas grill. If flame continues to be low, turn off gas at cylinder Vapor lock in connections. and grill. Disconnect the regulator from the LP gas cylinder. Reconnect the regulator to the LP gas cylinder. Perform a leak test. Relig
