Inhaltszusammenfassung zur Seite Nr. 1
ALWAYS AT YOUR COMMAND
Models 2022/2024/2042
GARAGE DOOR OPENERS
Includes: 2-Bulb Light System
Wall Console
®
Installer:
Includes INTELLICODE Remote Control
®
Safe-T-Beam System must be installed to close door.
Leave this manual
with homeowner.
For use only with sectional doors.
® ®
Homelink and Car2U compatible
For Answers and Assistance:
1.800.354.3643
®
Homelink is a registered trademark of
or visit www.geniecompany.com
Johnson Controls Technology Company.
®
Car2U is
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY INFORMATION OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on the owner or user of this system to read, understand and implement the information in this manual. If you have questions or do NOT ® understand the information presented, conta
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS OPENER FEATURES ® SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE INTELLICODE Rolling Code Security System. An electronic rolling code system that enhances the security of SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 the door opener by continuously changing the access code each time the remote control is used. The door opener OPENER FEATURES. . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM PRE-INSTALLATION CHECK LIST Things to consider if you are planning to "Do-it-yourself." This opener is designed for use with SECTIONAL doors only. In many cases you will be replacing an existing door opener with a new one, however, if this will be the first opener installed there are some pre-installation issues which need to be addressed. They are as follows: The Genie Company recommends that you read and fully understand all information and in
Inhaltszusammenfassung zur Seite Nr. 5
TYPICAL SECTIONAL DOOR INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Pg. 19 Pg. 13 5 1 Pg. 12-13 2 TYPICAL SUPPORT ADDED BRACKET HEADER BRACKET (NOT PROVIDED) MOUNTING BOARD BRACES POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLET EXTENSION SPRING OR TORSION SPRING Pg. 14 4 NOTE: This opener is designed for Pg. 17-18 use with SECTIONAL doors only. Pg. 17-18 6 3 3 Pg. 11 ® SAFE-T-BEAM MAX. 6" MIN. 5" 7 Pg. 12 SECTIONAL DOOR WARNING To reduce the risk of injury to persons or damag
Inhaltszusammenfassung zur Seite Nr. 6
RECOMMENDED TOOLS FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Pencil 3/16" Drill Bit Carpenter’s level Drill Wire strippers Adjustable wrench Ratchet Tape measure Safety Glasses Step ladder Hammer 1/4", 7/16", 3/8" and Phillips screwdriver 1/2" Sockets PARTS IDENTIFICATION - Not Shown Full Size . ARRANGING BOX CONTENTS FOR ASSEMBLY ORGANISATION DU CONTENU DE LA BOÎTE POUR LE MONTAGE DISPOS CIÓN DEL CONTEN DO DE LA BOLSA PARA EL MONTA E Remove i te nal box s nl ve l s bo t s i t rn s Qu
Inhaltszusammenfassung zur Seite Nr. 7
Shown Full size ( FASTENERS - See Parts List below for full description.) BAG NO. DESCRIPTION QUANTITY 0 RAIL SECTION CLAMP 2 RAIL CLAMP BOLT – 5/16 -18 x 5/8'' 8 HEX FLANGE NUT – 5/16 -18 8 1 BOLT – 5/16 -18 x 1/2'' 3 Rail Clamp Bolt - 5/16 -18 x 5/8" 2 CLEVIS PIN, LONG – 5/16" x 3" 1 COTTER PIN 1 HEADER BRACKET 1 LAG SCREW – 5/16'' x 2'' 2 3 HEX BOLT – 5/16 -18 x 3/4'' 5 #10-16 x 1-1/4" Phillips Hex Screw HEX FLANGE NUT – 5/16 -18 5 LAG SCREW – 5/16'' x 2'' 2 4 SELF DRILLING SCREW – 1/4 -20 x
Inhaltszusammenfassung zur Seite Nr. 8
FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 1-PIECE RAIL HARDWARE ASSEMBLED VIEW Power Cord Carriage Assembly Rail with chain Chain Connector Power Head CHAIN Release Knob Tensioner Chain Clevis Pin, Long BELT Header & Cotter Pin Bracket 3-PIECE RAIL HARDWARE ASSEMBLED VIEW Power Cord Carriage Assembly Rail with chain Rail Clamps Power Head Chain Connector Rail Clamp Bolts Release CHAIN Knob Rail with belt End Rail Rail Clamp Nuts Center Rail Tensioner Chain End Rail Clevis Pin, Long
Inhaltszusammenfassung zur Seite Nr. 9
IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of severe injury or death: 1. READ AND FOLLOW ALL SAFETY, INSTALLATION AND 5. Do NOT connect the opener to source of power until OPERATION INSTRUCTIONS. (If you have questions or do instructed to do so. not understand an instruction, call the Overhead 6. Locate the wall console: Door Corporation.) • Within sight of the garage door, 2. Install only on a properly balanced sectional or one piece • At minimum height of 5 feet so
Inhaltszusammenfassung zur Seite Nr. 10
Belt Rail Assembly for CHAIN DRIVE OPENER CHAIN DRIVE RAILS NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1. Chain Rail Center Rail A 3. Remove the two rail sections that are not connected to the chain and place them on floor (Fig. 1-2, A). End Rail 4. Carefully remove the third rail section with chain and plastic sleeve. Place rail section on floor and extend chain straight out Wire Tie(s) B (Fig. 1-2, B). Chain and rail should extend approximately 7 feet. 5. Remove wire
Inhaltszusammenfassung zur Seite Nr. 11
POWER HEAD & RAIL ASSEMBLY Use 5/16"-18 x 1/2" Assembly for CHAIN DRIVE OPENER Bolts NOTE: Handle carefully! Drive chain can slide out of rail. NOTE: For power head and rail assembly locate Bag 1 from Box 1. NOTE: Copy serial number from power head frame and record it on warranty page. FIG. 1-5 Rail - Power head assembly. 1. Attach rail assembly to power head by aligning the sprocket onto the motor shaft. Use (3) Chain Pulley Bracket (at wall end of rail) bolts, 5/16 -18 x 1/2" (Fig. 1-5). Use
Inhaltszusammenfassung zur Seite Nr. 12
final height mark door at highest point final height mark 2 1/2" door at highest point OPENER INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 2 b) - extend HEADER AND DOOR vertical line MOUNTING BRACKETS: 2-1/2" WARNING Header bracket must be fastened to garage d) - final c) - door at framing. Do NOT fasten to drywall, particle height mark board, plaster or other such materials. highest point 1. Finding header bracket mounting location. • Close garage door. – Use a pencil and l
Inhaltszusammenfassung zur Seite Nr. 13
NO HEADER BRACKET MOUNTING THE OPENER: 1. Getting started. • Position assembled rail on wall next to header bracket (Fig. 2-4). – Place material on floor under power head to protect from scratching. (A box, stool, or VIEW similar device may be needed to clear a FROM ABOVE (not to scale) torsion spring.) NOTE: For header bracket pins locate Bag 2 from Box 1. 2. Mounting the assembly. YES / SÍ / OUI • Attach rail to header bracket using clevis pin and cotter pin (Fig. 2-5). FIG. 2-4 Positio
Inhaltszusammenfassung zur Seite Nr. 14
DOOR BRACKET: CAUTION Doors made of masonite, lightweight wood, centerline fiberglass, and sheet metal must be properly braced before mounting door opener. Contact door manufacturer or distributor for a bracing kit. centerline The Genie Company is not responsible for even with or damage caused due to improperly braced door. above top roller NOTE: For door bracket and bolts locate Bag 4 FIG. 2-7 Mounting door Bracket. from Box 2. 1. Finding door bracket mounting location. • Door bracket is mo
Inhaltszusammenfassung zur Seite Nr. 15
WALL CONSOLE INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 3 Wire from WARNING power head Verify there is NO power to the opener before to Wall Console installing Wall Console wires and Wall Console. CAUTION Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the Wall Console to stop working. When using the insulated staples, make sure you fasten them only as tightly as needed to hold the wire snugly. Wall Console WARNING "Entrapment" Use of any
Inhaltszusammenfassung zur Seite Nr. 16
Child can be pinned under automatic garage door. Death or serious injury can result. •Never let child walk or run under moving do.or. Never let child use door opener controls. • Always keep moving door in sight. • •If person is pinned, push control button or use emergency release. Test door opener monthly: • Refer o your owner s manual P ace 1/ - nch object (or 2x4 laid f at) on floor If door a ls o reverse on con act adjust opener If opener s i l a ls o reverse door repair or replace open
Inhaltszusammenfassung zur Seite Nr. 17
® AFE-T-BEAM SYSTEM INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 4 WARNING There should be no electrical power to the opener ® while installing Safe-T-Beam wires. If you have plugged in the power cord—UNPLUG IT NOW! N OTE: The opener will not close the door ® automatically unless the Safe-T-Beam System is installed. mark NOTE: For Safe-T-Beam®, screws, wire, and insulated staples locate items and Bag 8 from Box 3. FIG. 4-1 Mark door frame. 1. Mounting brackets. • Mark both si
Inhaltszusammenfassung zur Seite Nr. 18
3b. Wiring (pre-wired). ® • Route wire from wall to Safe-T-Beam sensors Wall Wall (Fig. 4-5b). • Splice pre-wiring to shortened sensor wire, Source Sensor match wire pairs dash-to-dash (striped-to- striped) and plain-to-plain (white-to-white). - Trim sensor wire to approximately one foot (1 ft) from sensor. - Split and strip ends of sensor wires and Ceiling 6 5 4 3 2 1 or 6 5 4 3 2 1 pre-wired wires (Fig. 4-7). - Splice wires together with (provided) Power Dashed Lin
Inhaltszusammenfassung zur Seite Nr. 19
ONNECTING TO POWER FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 5 WARNING • To reduce the risk of electrical shock, this equipment FIG. 5-1 Connect to power. has a grounded type plug that includes a third (grounding) pin. This plug will only fit a grounded type outlet. If you do not have a grounded outlet, contact Motor Cover Screws a qualified licensed electrician to install one. DO NOT alter the plug in any way. The door opener must be properly grounded in order to prevent personal injur
Inhaltszusammenfassung zur Seite Nr. 20
Move in this direction Move in this direction OOR LIMITS FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 6 WARNING Limit Controls location on power head. • Severe injury or death can result if the door closing force is set too high. NOTE: Set Close Travel Limit • Never increase the door closing force above the before setting Open Travel minimum required to move the door. Limit for unit to operate • Never adjust force to compensate for a sticking normally. or binding door. Unless limits ar
