Inhaltszusammenfassung zur Seite Nr. 1
The Chamberlain Group, Inc.
A DUCHOSSOIS ENTERPRISE
845 Larch Avenue
Elmhurst, Illinois 60126-1196
Complies with UL 325
regulations effective
®
January 1, 1993
GARAGE DOOR OPENER
Model M200
1/2 HP
For Residential Use Only
Owner’s Manual
n Please read this manual and the enclosed safety materials carefully!
n Fasten the manual near the garage door after installation.
®
n The door WILL NOT CLOSE unless the Protector System is connected and
properly aligned.
n Periodic checks of the opener are req
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS Introduction Pages 2-5 Adjustment Pages 24-26 Safety symbol and signal word review........................2 Adjust the travel limits ...............................................24 Preparing your garage door ........................................3 Adjust the force .........................................................25 Tools needed...............................................................3 Test the safety reversal system.................................26 ® Plannin
Inhaltszusammenfassung zur Seite Nr. 3
1 Preparing your garage door WARNING Before you begin: To prevent possible SERIOUS INJURY OR DEATH: • Disable locks. • ALWAYS call a trained door systems technician if • Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when • Complete the following test to make sure your required. garage door is balanced and is not sticking or binding: • NEVER try to loosen, move or adjust garage door, door springs, cables, pul
Inhaltszusammenfassung zur Seite Nr. 4
— — — — — — — — Planning Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener. SECTIONAL DOOR INSTALLATION FINISHED CEILING Support bracket & fastening hardware Horizontal and vertical reinforcement is required. is needed
Inhaltszusammenfassung zur Seite Nr. 5
Carton Inventory Your garage door opener is packaged in two cartons purchased. If anything is missing, carefully check the which contain the motor unit and all parts illustrated packing material. Parts may be stuck in the foam. below. Accessories will depend on the model Hardware for installation is also listed below. Belt Cap Retainer Remote Control Styrofoam SECURITY: Transmitter Visor Clip 3-Channel Remote Control Belt Multi-Function Door Control Panel Light Lens (2) One-Piece T-rail 2-Cond
Inhaltszusammenfassung zur Seite Nr. 6
CAUTION ASSEMBLY STEP 1 Attach the T-Rail to the Motor Unit To avoid serious damage to opener, ONLY use screws mounted in top of motor unit. To avoid installation difficulties, do not run the garage door opener until instructed to do so. Washered Screw Styrofoam • Remove the two washered screws mounted in top 5/16"-18x1/2" of motor unit. • Align T-rail and styrofoam over sprocket. Cut tape USE ONLY THIS from T-rail, belt and styrofoam. TYPE AND SIZE SCREW • REMOVE STYROFOAM. • Insert both washe
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY STEP 3 WARNING Attach the Belt Cap Retainer To avoid possible SERIOUS INJURY to fingers from moving garage door opener: • Position the belt cap retainer over the motor unit • ALWAYS keep hand clear of sprocket while operating sprocket so the two holes in cap align with the two opener. holes in mounting plate. Attach with #8x3/8" hex • Securely attach sprocket cover before operating. screws provided. You have now finished assembling your garage Belt Cap door opener. Please read the follo
Inhaltszusammenfassung zur Seite Nr. 8
INSTALLATION STEP 1 Determine the Header Bracket Finished Vertical Ceiling Centerline Location Header Structural 2x4 Wall Supports WARNING To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. • Concrete anchors MUST be used if mounting header Vertical bracket or 2x4 into masonry. Centerline • NEVER try to loosen, mov
Inhaltszusammenfassung zur Seite Nr. 9
ONE-PIECE DOOR WITHOUT TRACK Unfinished 1. Close the door and mark the inside vertical Ceiling centerline of your garage door. Extend the line Structural onto the header wall above door, as shown. Supports Header Wall Vertical If headroom clearance is minimal, you can install Centerline the header bracket on the ceiling. See page 10. 2x4 2x4 If you need to install the header bracket on a 2x4 OPTIONAL (on wall or ceiling), use lag screws (not provided) CEILING MOUNT to securely fasten the 2x4 to
Inhaltszusammenfassung zur Seite Nr. 10
INSTALLATION STEP 2 Install the Header Bracket Wall Mounting Holes You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the CEILING MOUNT ONLY The nail hole is for instructions which will work best for your particular positioning only. You must use lag screws requirements. Do not install the header bracket UP to mount the header bracket. over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER BRACKET INSTALLATI
Inhaltszusammenfassung zur Seite Nr. 11
INCREASE INCREASE DOWN UP TRAVEL TRAVEL INSTALLATION STEP 3 Attach the T-Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring. • Position the rail bracket against the header Header Wall bracket. • Align the bracket holes and join with a clevis pin Header B
Inhaltszusammenfassung zur Seite Nr. 12
INSTALLATION STEP 4 CAUTION Position the Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door- to-rail distance. • Raise the opener onto a stepladder. You will need T-rail 2x4 help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 laid
Inhaltszusammenfassung zur Seite Nr. 13
INSTALLATION STEP 5 WARNING Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural Two representative installations are shown. Yours supports of the garage. Concrete anchors MUST be used may be different. Hanging brackets should be angled if installing any brackets into masonry. (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before installing the opener. This
Inhaltszusammenfassung zur Seite Nr. 14
1 1 LIGHT LIGHT LIGHT INSTALLATION STEP 6 WARNING Install the Door Control To prevent possible serious injury or death from electrocution: Locate door control within sight of the door at a • Be sure power is not connected before installing door minimum height of 5 feet where small children control. cannot reach, and away from moving parts of the • Connect only to 24 VOLT low voltage wires. door and door hardware. If installing into drywall To prevent possible serious injury or death from a clos
Inhaltszusammenfassung zur Seite Nr. 15
NOTICE Lens INSTALLATION STEP 7 Tab Lens Install the Lights and Lenses Guide 75 Watt Maximum • Install a 75 watt maximum light bulb in each Light Bulb socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF. • Slide lenses into guides. Snap bottom tabs into lens slots. 75 Watt • Reverse the procedure to remove the lenses. Maximum Light Bulb • If the bulbs burn out prematurely due to vibration, Lens Slot replace with a
Inhaltszusammenfassung zur Seite Nr. 16
INSTALLATION STEP 9 WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third • Garage door installation and wiring MUST be in grounding
Inhaltszusammenfassung zur Seite Nr. 17
INSTALLATION STEP 10 WARNING ® Install The Protector System • Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. The safety reversing sensor must be connected • To prevent SERIOUS INJURY or DEATH from a closing and aligned correctly before the garage door garage door: opener will move in the down direction. – Correctly connect and align the safety reversing IMPORTANT INFORMATION ABOUT sensor. This required safety device MUST NOT be THE SAFETY
Inhaltszusammenfassung zur Seite Nr. 18
INSTALLING THE BRACKETS Figure 1 Be sure power to the opener is disconnected. DOOR TRACK MOUNT (RIGHT SIDE) Install and align the brackets so the sensors will face each other across the garage door, with the beam no Door higher than 6" above the floor. They may be installed Track in one of three ways, as follows. Lip Garage door track installation (preferred): Indicator light • Slip the curved arms over the rounded edge of each door track, with the curved arms facing the door. Snap into place
Inhaltszusammenfassung zur Seite Nr. 19
MOUNTING AND WIRING THE SAFETY SENSORS Figure 4 • Slide a 1/4"-20x1/2" carriage bolt head into the slot Wing nut on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension. See Figure 4. 1/4"-20x1/2" Carriage bolt • Finger tighten the wing nuts. Lens • Run the wires from both sensors to the opener. Use insulated staples to secure wire to wall and ceiling. TROUBLESHOOTING THE SAFE
Inhaltszusammenfassung zur Seite Nr. 20
INSTALLATION STEP 11 CAUTION Fasten the Door Bracket To prevent damage to garage door, reinforce inside of door with angle iron both vertically and horizontally. Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long Header enough to be secured to two or three vertical Bracket supports. A vertical reinforcement brace should cover the height of the top panel. Figure 1 shows one piece of angle iron as the h
