Inhaltszusammenfassung zur Seite Nr. 1
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.liftmaster.com
®
GARAGE DOOR OPENER
Model 3595LM 3/4 HP
For Residential Use
Install on Sectional Doors ONLY
THIS OPERATOR IS INTENDED FOR USE ONLY WITH I-BEAM RAILS.
Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
®
■ The door WILL NOT CLOSE unless the Protector System is connected and
properly aligned.
■ Periodic checks
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS Introduction 2-5 Adjustment 20-22 Safety symbol and signal word review........................2 Adjust the travel limits ...............................................20 Preparing your garage door ........................................3 Adjust the force .........................................................21 Tools needed...............................................................3 Test the safety reversal system.................................22 ® Planning ..........
Inhaltszusammenfassung zur Seite Nr. 3
1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY OR DEATH: • Disable locks. • ALWAYS call a trained door systems technician if CAUTION WARNING • Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when • Complete the following test to make sure your required. garage door is balanced and is not sticking or binding: • NEVER try to loosen, move or adjust garage door, d
Inhaltszusammenfassung zur Seite Nr. 4
— — — — — — — — Planning WARNING WARNING Identify the type and height of your garage door. Without a properly working safety reversal system, Survey your garage area to see if any of the persons (particularly small children) could be conditions below apply to your installation. Additional CAUTION SERIOUSLY INJURED or KILLED by a closing garage WARNING materials may be required. You may find it helpful to door. refer back to this page and the accompanying • The gap between the bott
Inhaltszusammenfassung zur Seite Nr. 5
LOCK LIGHT Carton Inventory Your garage door opener is packaged in two cartons purchased. If anything is missing, carefully check the which contain the motor unit and all parts illustrated packing material. Parts may be stuck in the foam. below. Accessories will depend on the model Hardware for installation is also listed below. ® Remote Control Security Transmitter Visor Clip 3-Button Remote Control Chassis Support Motion Detecting Bracket Door Control Panel Header Bracket Chain Motor Unit W
Inhaltszusammenfassung zur Seite Nr. 6
WARNING WARNING ASSEMBLY STEP 1 CAUTION WARNING Attach the Rail to the Motor Unit To avoid SERIOUS damage to opener, ONLY use bolts/fasteners, mounted in top of motor unit. To avoid installation difficulties, do not run the garage door opener until instructed to do so. Figure 1 Washered Bolt • Remove the bolt and lock nut from the top of the 5/16"-18x1/2" motor unit. Lock Nut • Place rail onto the bolt mounted on the motor unit and align the back hole with the hole in the top of the unit. • Fas
Inhaltszusammenfassung zur Seite Nr. 7
Lock ASSEMBLY STEP 4 Washer Outer Nut Inner Nut Tighten the Chain To Tighten Outer Nut • Spin the inner nut and lock washer down the To Tighten Inner Nut threaded shaft, away from the trolley. • To tighten the chain, turn outer nut in the direction shown. As you turn the nut, keep the chain from twisting. Trolley • When the chain is approximately 1/2" (13 mm) above the base of the rail at its midpoint, re-tighten the inner nut to secure the adjustment. Chain Sprocket noise can result if chain i
Inhaltszusammenfassung zur Seite Nr. 8
INSTALLATION STEP 1 Unfinished OPTIONAL Ceiling Determine the Header Bracket CEILING MOUNT Location FOR HEADER WARNING BRACKET WARNING 2x4 Header Wall To prevent possible SERIOUS INJURY or DEATH: Vertical Centerline of Garage Door • Header bracket MUST be RIGIDLY fastened to CAUTION WARNING structural support on header wall or ceiling, otherwise 2x4 Structural garage door might not reverse when required. DO NOT Supports install header bracket over drywall. • Concrete anchors MUST be used if moun
Inhaltszusammenfassung zur Seite Nr. 9
INSTALLATION STEP 2 Install the Header Bracket Wall Mounting Holes You can attach the header bracket either to the wall CEILING MOUNT ONLY above the garage door, or to the ceiling. Follow the The nail hole is for positioning only. instructions which will work best for your particular You must use lag screws UP requirements. Do not install the header bracket to mount the header bracket. over drywall. If installing into masonry, use concrete anchors (not provided). Optional WALL HEADER BRACKET
Inhaltszusammenfassung zur Seite Nr. 10
INSTALLATION STEP 3 Attach the Rail to the Header Header Wall Bracket Header Bracket Chain • Position the opener on the garage floor below the Pulley header bracket. Use packing material as a Bracket Header protective base. NOTE: If the door spring is in the Bracket way you’ll need help. Have someone hold the Ring opener securely on a temporary support to allow Fastener the rail to clear the spring. • Position the rail bracket against the header Clevis Pin bracket. 5/16"x2-3/4" • Align the brac
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLATION STEP 5 WARNING WARNING Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural Three representative installations are shown. Yours CAUTION WARNING supports of the garage. Concrete anchors MUST be used may be different. Hanging brackets should be angled if installing any brackets into masonry. (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural suppo
Inhaltszusammenfassung zur Seite Nr. 12
LOCK LIGHT LOCK LIGHT WARNING WARNING INSTALLATION STEP 6 CAUTION WARNING Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: Locate door control within sight of the door at a • Be sure power is not connected BEFORE installing door minimum height of 5 feet (1.5 m) where small children control. cannot reach, and away from moving parts of the door • Connect ONLY to 24 VOLT low voltage wires. and door hardware. The installation surface must be To prevent possib
Inhaltszusammenfassung zur Seite Nr. 13
NOTICE WARNING WARNING INSTALLATION STEP 7 CAUTION WARNING Install the Light To prevent possible OVERHEATING of the endpanel or light socket, • Press the release tabs on both sides of lens. • DO NOT use short neck or specialty light bulbs. Gently rotate lens back and downward until the • DO NOT use halogen bulbs. Use ONLY incandescent. lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. The light will turn ON and remai
Inhaltszusammenfassung zur Seite Nr. 14
INST WALLA ARNING TION STEP 9 WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the CAUTION WARNING • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third • Garage door installation and wi
Inhaltszusammenfassung zur Seite Nr. 15
INSTALLATION STEP 10 WARNING WARNING ® Install The Protector System • Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. The safety reversing sensor must be connected CAUTION WARNING • To prevent SERIOUS INJURY or DEATH from a closing and aligned correctly before the garage door garage door: opener will move in the down direction. – Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be IMPORTANT INFOR
Inhaltszusammenfassung zur Seite Nr. 16
INSTALLING THE BRACKETS Figure 1 Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face DOOR TRACK MOUNT (RIGHT SIDE) each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. They may be Door installed in one of three ways, as follows: Track Garage door track installation (preferred): Lip Indicator • Slip the curved arms over the rounded edge of light each door track, with the curved arms facing the door. Snap int
Inhaltszusammenfassung zur Seite Nr. 17
MOUNTING AND WIRING THE SAFETY SENSORS Figure 4 • Slide a 1/4"-20x1/2" carriage bolt head into the slot Wing Nut on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 4). Carriage Bolt 1/4"-20x1/2" • Finger tighten the wing nuts. Lens • Run the wires from both sensors to the opener. Use insulated staples to secure wire to wall and ceiling. TROUBLESHOOTING THE SAFETY
Inhaltszusammenfassung zur Seite Nr. 18
WARNING WARNING INSTALLATION STEP 11 CAUTION WARNING Fasten the Door Bracket Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of Follow instructions which apply to your door type as door bracket. Contact your door manufacturer for illustrated below or on the following page. reinforcement kit. A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should Header cov
Inhaltszusammenfassung zur Seite Nr. 19
INSTALLATION STEP 12 Inner Trolley Connect Door Arm to Trolley SECTIONAL DOORS ONLY Outer Trolley • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer Clevis Pin trolley from the inner trolley. Slide the outer trolley 5/16"x1" Ring back (away from the door) about 2" (5 cm) as Fastener shown in Figures 1, 2 and 3. • Figure 1: – Fasten straight door arm section to outer trolley with the 5/16"x1" clevis pin. Secure the Door connection with a ring faste
Inhaltszusammenfassung zur Seite Nr. 20
ADJUSTMENT STEP 1 WARNING WARNING Adjust the UP and DOWN Travel Without a properly installed safety reversal system, Limits persons (particularly small children) could be CAUTION WARNING SERIOUSLY INJURED or KILLED by a closing garage Limit adjustment settings regulate the points at which door. the door will stop when moving up or down. • Incorrect adjustment of garage door travel limits will To operate the opener, press the Door Control push interfere with proper operation of safety reversal ba