Bedienungsanleitung Chamberlain 2000UK

Inhaltszusammenfassung zur Seite Nr. 1

GB
Instructions – Garage Door Operator – Model MotorLift 2000UK
TM
Alfred Nobel Str. 4 - 66793 Saarwellingen, Germany
GB
For Service: 0800 317847

Inhaltszusammenfassung zur Seite Nr. 2

START BY READING THESE IMPORTANT SAFETY RULES These safety alert symbols mean Caution – a personal safety or property damage instruction. Read these instructions carefully. This garage door opener is designed and tested to offer reasonable safe service provided it is installed and operated in strict accordance with the following safety rules. Failure to comply with the following instructions may result in serious personal injury or property damage. Caution: If your garage has no service entrance

Inhaltszusammenfassung zur Seite Nr. 3

BEFORE YOU BEGIN: FASTEN T-RAIL TO THE OPENER – 8 1. Look at the wall or ceiling above the garage door. The header Place packing material under the opener to protect the opener cover. bracket must be securely fastened to structural supports. For convenience, place a support under the cable pulley bracket end of rail. 2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not supplied) may be required. Remove the (2) washered screws (1) from

Inhaltszusammenfassung zur Seite Nr. 4

INSTALLATION SECTION 11 – 19 HANG THE OPENER – 15 The opener must be securely fastened to a structural support of the garage. Three representative installations are shown. Yours may be Wear protective goggles when working overhead to protect your different. Hanging brackets (1) should be angled (Figure A) to eyes from injury. provide rigid support. On finished ceilings, (Figure B) attach a sturdy Disengage all existing garage door locks to avoid damage to the metal bracket (not supplied) (4) to

Inhaltszusammenfassung zur Seite Nr. 5

FASTEN DOOR BRACKET – 18 PROGRAM YOUR OPENER & REMOTE – 20 If yours is a canopy or dual-track style garage door, a door arm Activate the opener only when door is in full view, free of conversion kit is required. Follow the installation instructions included obstruction and properly adjusted. No one should enter or leave with the replacement door arm. Exercise care in removing and garage while door is in motion. Do not allow children to operate assembling arm conversion kit. Keep fingers away fro

Inhaltszusammenfassung zur Seite Nr. 6

OPERATION OF YOUR OPENER FORCE ADJUSTMENT – 22 The force, as measured on the closing edge of the door, should Your opener can be activated by any of the following devices: not exceed 150 N (15kg). If the closing force is adjusted to more • The Lighted Door Control Button (optional). Hold the button down than 150 N, the Protector System must be installed. until door starts to move. Do not use force adjustments to compensate for a binding or • The Outside Keylock or Keyless Entry System (if you ha

Inhaltszusammenfassung zur Seite Nr. 7

5. Opener noise is disturbing in living quarters of home: MAINTENANCE OF YOUR OPENER If operational noise is a problem because of proximity of the opener to Once a Month: the living quarters, Vibration Isolator Kit 41A3263 can be installed. • Repeat safety reverse test. Make any necessary adjustments. This kit was designed to reduce the "sounding board effect" and is easy to install. • Manually operate door. If it is unbalanced or binding, call for professional garage door service. • Check to be

Inhaltszusammenfassung zur Seite Nr. 8

SPECIFICATIONS ACCESSORIES – 25 (1) Model 4180EML ........................Single-Function Remote Control Rated Pull Force .............600N Motor (2) Model 4183EML ........................3-Function Remote Control Type................................Permanent split capacitor (3) Model 4185EML ........................3-Function Mini Remote Control Speed..............................1500 rpm (4) Model 845EML ..........................Multi-Function Door Control Panel Volts.........................