Bedienungsanleitung Edelbrock PRO-FLO XT 3528

Bedienungsanleitung für das Gerät Edelbrock PRO-FLO XT 3528

Gerät: Edelbrock PRO-FLO XT 3528
Kategorie: Autoteile
Produzent: Edelbrock
Größe: 1.26 MB
Datum des Hinzufügens: 6/13/2013
Seitenanzahl: 39
Anleitung drucken

Herunterladen

Wie kann man es nutzen?

Unser Ziel ist Ihnen einen schnellen Zugang zu Inhalten in Bedienungsanleitungen zum Gerät Edelbrock PRO-FLO XT 3528 zu garantieren. Wenn Sie eine Online-Ansicht nutzten, können Sie den Inhaltsverzeichnis schnell durchschauen und direkt zu der Seite gelangen, auf der Sie die Lösung zu Ihrem Problem mit Edelbrock PRO-FLO XT 3528 finden.

Für Ihre Bequemlichkeit

Wenn das direkte Durchschauen der Anleitung Edelbrock PRO-FLO XT 3528 auf unserer Seite für Sie unbequem ist, können sie die folgende zwei Möglichkeiten nutzen:

  • Vollbildsuche – Um bequem die Anleitung durchzusuchen (ohne sie auf den Computer herunterzuladen) können Sie den Vollbildsuchmodus nutzen. Um das Durchschauen der Anleitung Edelbrock PRO-FLO XT 3528 im Vollbildmodus zu starten, nutzen Sie die Schaltfläche Vollbild
  • Auf Computer herunterladen – Sie können die Anleitung Edelbrock PRO-FLO XT 3528 auch auf Ihren Computer herunterladen und sie in Ihren Sammlungen aufbewahren. Wenn Sie jedoch keinen Platz auf Ihrem Gerät verschwenden möchten, können Sie sie immer auf ManualsBase herunterladen.
Edelbrock PRO-FLO XT 3528 Handbuch - Online PDF
Advertisement
« Page 1 of 39 »
Advertisement
Druckversion

Viele Personen lesen lieber Dokumente nicht am Bildschirm, sondern in gedruckter Version. Eine Druckoption der Anleitung wurde ebenfalls durchdacht, und Sie können Sie nutzen, indem Sie den Link klicken, der sich oben befindet - Anleitung drucken. Sie müssen nicht die ganze Edelbrock PRO-FLO XT 3528 Anleitung drucken, sondern nur die Seiten, die Sie brauchen. Schätzen Sie das Papier.

Zusammenfassungen

Unten finden Sie Trailer des Inhalts, der sich auf den nächsten Anleitungsseiten zu Edelbrock PRO-FLO XT 3528 befindet. Wenn Sie den Seiteninhalt der nächsten Seiten schnell durchschauen möchten, können Sie sie nutzen.

Inhaltszusammenfassungen
Inhaltszusammenfassung zur Seite Nr. 1

TABLE OF CONTENTS
Part #3527 and #3528
Introduction.................................................................................................................................................1
Components................................................................................................................................................2
Preliminaries.....................................................................................................................................

Inhaltszusammenfassung zur Seite Nr. 2

PRIMARY KIT COMPONENTS ❑ Electronic Control Unit/System ECU ❑ Fuel filter ❑ Calibration Module ❑ Fuel rail assembly ❑ Distributor conversion kit ❑ Fuel pressure regulator ❑ Fuel injectors ❑ High pressure fuel pump ❑ ECU power relay/Fuel pump relay ❑ Intake manifold ❑ Manifold Absolute Pressure (MAP) Sensor ❑ Four barrel air valve ❑ Manifold Air Temperature (MAT) Sensor ❑ Idle Air Control (IAC) solenoid, integrated with air valve ❑ Coolant Temperature Sensor (CTS) ❑ Main system harness ❑ Throttle

Inhaltszusammenfassung zur Seite Nr. 3

TOOLS AND EQUIPMENT HARDWARE AND PARTS RECOMMENDED Use the following checklist for items needed. Use the following checklist for items needed. ❑ Box and open end wrenches ❑ Intake gasket; #3527 kits use Edelbrock gaskets #7201; #3528 kits use gaskets #7235 ❑ Socket set ❑ Pipe plugs, if needed ❑ Distributor wrench ❑ 5/16-inch steel tubing (approximate equal length to fuel pickup ❑ Pliers (channel locks and hose clamp) line in tank) ❑ Screwdrivers (regular and Phillips) ❑ Edelbrock Gasgacinch #930

Inhaltszusammenfassung zur Seite Nr. 4

MANIFOLD & CARBURETOR HEIGHT VS. PRO-FLO XT HEIGHT 1. Lay a straightedge (such as a yardstick) across the top of the air cleaner from front to back. 2. Measure from block and manifold end seal surfaces to straightedge. 3. Record these measurements (height A and height B). 4. Add height A and height B and divide by two to get the average height. 5. The Pro-Flo XT manifold is 9” tall at the center and 9.125” at the throttle body flange. 6. Compare this to your original measurements. If the Pro-Fl

Inhaltszusammenfassung zur Seite Nr. 5

FUEL REQUIREMENTS Because the Pro-Flo XT system uses an Oxygen sensor, you must use unleaded fuel only. Leaded fuels will damage the O sensor. If you do use 2 leaded fuel in your vehicle, do not install the O sensor and do not operate the vehicle in the closed loop fuel mode. 2 AUTOMATIC TRANSMISSION CHECK For best performance, economy, and emissions, the shift point must be checked before and after the manifold change. NOTE: This check should be performed ONLY at a sanctioned drag strip or tes

Inhaltszusammenfassung zur Seite Nr. 6

FUEL SYSTEM Because your Edelbrock Pro-Flo XT system controls fuel delivery very differently than a carburetor, some conversions to your fuel system are necessary. Pro-Flo XT electronic fuel injection requires high and constant fuel volume and fuel pressure. For this reason, a good primary fuel line is critical. The Pro-Flo XT system includes a 3/8-inch high pressure fuel line which must be used as the primary fuel line. The fuel that bypasses the injectors must be returned to the fuel tank vi

Inhaltszusammenfassung zur Seite Nr. 7

RUBBER RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line enters the tank. This will be the hole for your return line. Insert a short length of 5/16-inch hard line (available at most radiator shops) into the hole and weld it to the sending unit plate. The hard line should extend through the hole 1 to 2 inches on each side of the plate. Connect a length (at least 4 inches) of 5/16-inch rubber return line hose to the hard line that will extend into

Inhaltszusammenfassung zur Seite Nr. 8

BULKHEAD FITTING METHOD HARD RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line, enters the tank. This will be the hole for your return line. Insert a length of 5/16-inch hard line (available at most radiator shops) into the hole and weld it to the sending unit plate. The hard line should extend through the hole 1 to 2 inches on the outside of the plate. On the inside of the plate, the hard line should follow the contours of the fuel pickup line.

Inhaltszusammenfassung zur Seite Nr. 9

NOTE: ALL WELDING AND SOLDERING OF THE FUEL SYSTEM MUST BE PERFORMED BY A PROFESSIONAL RADIATOR AND/OR FUEL SYSTEM REPAIR SHOP. FUEL SYSTEM INSTALLATION 1. Drain the fuel tank. 2. Remove all fuel lines from the tank and from the carburetor. 3. Remove the fuel tank. NOTE: While the fuel tank is removed from the car, it is recommended that it be professionally cleaned in order to remove any rust or dirt that may have accumulated inside and which could damage the injectors. 4. Remove the sending u

Inhaltszusammenfassung zur Seite Nr. 10

ASSEMBLING PRO-CLASSIC HOSE Step One: Cut hose to length, Step Two: Unscrew socket Step Three: Apply Russell Step Four: Hold socket/hose in as straight and square as from hose end. Push hose into assembly lube to threads on vise. Turn nipple with wrench possible, with razor blade-type socket, turning counter- nipple assembly and in socket. until there is less than 1/16" hose cutter or shears. clockwise, until hose is seated Insert nipple into socket/hose between nipple hex and socket. against s

Inhaltszusammenfassung zur Seite Nr. 11

PRE-INSTALLATION Before installing the induction system, take the following steps to ensure successful installation and performance 1. Check all components thoroughly for damage. 2. Make sure all throttle linkages open entirely and close freely. 3. Make sure all fuel inlet and vacuum ports are free from packing material. 4. Check the installation kit for proper parts. REMOVING THE STOCK CARBURETOR AND MANIFOLD 1. Disconnect battery. 2. For ease of installation, keep all parts in order. CAUTION:

Inhaltszusammenfassung zur Seite Nr. 12

GASKET SURFACE PREPARATION CAUTION: Replace all gaskets as recommended. Do not use race-type non-embossed gaskets for street applications. Due to material deterioration under street driving conditions, internal vacuum and oil leaks may occur. We recommend Edelbrock gasket #7201 for kit #3527 and #7235 for kit #3528. Do not use Fel-Pro Permatorque Blue gaskets, which are designed for use on stock cast iron intake manifolds only. 1. Check gaskets on head surface and manifold to make sure they a

Inhaltszusammenfassung zur Seite Nr. 13

SENSORS The Edelbrock Pro-Flo XT system interprets overall engine operating conditions and fuel/spark requirements based on readings from sensors that measure specific engine conditions. The Pro-Flo system includes five sensors: 1) Manifold Absolute Pressure 2) Manifold Air Temperature 3) Coolant Temperature 4) Throttle Position 5) Exhaust Oxygen (O ) 2 MANIFOLD ABSOLUTE PRESSURE SENSOR The Manifold Absolute Pressure sensor, mounted on the intake plenum, converts air pressure (load) in the m

Inhaltszusammenfassung zur Seite Nr. 14

THROTTLE POSITION SENSOR The Throttle Position Sensor, an integral part of the Pro-Flo throttle body, measures throttle angle. COOLANT TEMPERATURE SENSOR The Coolant Temperature Sensor is a thermistor device like the Manifold Air Temperature sensor. Resistance varies as coolant temperature rises and lowers. The Coolant Temperature Sensor is located at the front of the manifold on the driver’s side. OXYGEN (O ) SENSOR 2 An oxygen sensor, installed on the header collector pipe, measures exhaust ga

Inhaltszusammenfassung zur Seite Nr. 15

O SENSOR INSTALLATION 2 The exhaust gas oxygen content is determined by the oxygen sensor. The sensor signals the ECU, which compensates when the air/fuel mixture is either rich or lean. NOTE: It is recommended that the O sensor installation be performed by a professional muffler shop. 2 1. Double check header gaskets, replacing if necessary. 2. Drill a 1/2-inch to 9/16-inch hole in the passenger-side header collector reducer, as close to the header flange as possible. (1" to 3" away) NOTE: Bef

Inhaltszusammenfassung zur Seite Nr. 16

ENGINE HARNESS LAYOUT Catalog #3527, #3528 16 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527

Inhaltszusammenfassung zur Seite Nr. 17

MAIN SYSTEM HARNESS This diagram illustrates the chassis side of the Pro-Flo XT Main System Harness. Catalog #3527, #3528 17 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527

Inhaltszusammenfassung zur Seite Nr. 18

Catalog #3527, #3528 18 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527

Inhaltszusammenfassung zur Seite Nr. 19

MAIN SYSTEM HARNESS This diagram illustrates the engine side of the Pro-Flo XT Main System Harness. Catalog #3527, #3528 19 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527

Inhaltszusammenfassung zur Seite Nr. 20

Catalog #3527, #3528 20 ©2008 Edelbrock Corporation Rev. 8/08 - AJ/mc Pro-Flo EFI Installation Instructions Brochure No. 63-3527


Ähnliche Anleitungen
# Bedienungsanleitung Kategorie Herunterladen
1 Edelbrock 1109 Handbuch Autoteile 5
2 Edelbrock 1107 Handbuch Autoteile 2
3 Edelbrock 1208 Handbuch Autoteile 0
4 Edelbrock 1221* Handbuch Autoteile 1
5 Edelbrock 1222* Handbuch Autoteile 0
6 Edelbrock 1209 Handbuch Autoteile 1
7 Edelbrock 1400 Handbuch Autoteile 2
8 Edelbrock 1477 Handbuch Autoteile 8
9 Edelbrock 1483 Handbuch Autoteile 0
10 Edelbrock 15004 Handbuch Autoteile 0
11 Edelbrock 15010 Handbuch Autoteile 0
12 Edelbrock 15017 Handbuch Autoteile 0
13 Edelbrock 15016 Handbuch Autoteile 0
14 Edelbrock 15042 Handbuch Autoteile 0
15 Edelbrock 15521 Handbuch Autoteile 0
16 Sony BP-GL95 Handbuch Autoteile 25
17 Sony BP-GL65 Handbuch Autoteile 2
18 Philips Epic 50PF9966 Handbuch Autoteile 3
19 Philips HTS3011 Handbuch Autoteile 2
20 Philips SDJ6040W Handbuch Autoteile 1