Inhaltszusammenfassung zur Seite Nr. 1
UV-AIRE™ AIR PURIFYING SYSTEM
Model: UV-18X
ITEMS INCLUDED IN KIT:
1-UV-Aire ™ power unit
4-Sheet metal mounting screws
2-Angled mounting brackets
2-Flat mounting brackets
1-Duct board mounting bracket
2-Ultra Violet lamps
1-Instruction Sheet
2-Wing nuts
Caution Labels
Gasket
UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a
homes’ heating and air conditioning system. The treatment is a safe, silent, and proven way
to make your home
Inhaltszusammenfassung zur Seite Nr. 2
I. INDICATION FOR USE This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for use in the mitigation, treatment, or prevention of any disease or condition. II. GENERAL INFORMATION There are different size units available, depending on the square footage of your home. See chart below for determining your homes needs. Minimum Max Air Lamp Intensity at 1 Recommended Model Duct Volts Amps Watts Hz Temp °F meter Max Sq. Feet
Inhaltszusammenfassung zur Seite Nr. 3
2. Determine the type of duct you have. (For flex duct applications, refer to Figure 21 on page 8) IF YOU HAVE METAL DUCT: a. Apply supplied wet and stick mounting template to air duct in either a vertical or horizontal position as shown in Figure 2. b. Drill 1/8” diameter mounting holes at positions indicated on template. c. Cut out rectangular hole on template using a pair of tin snips or jigsaw. (See Figure 2) Remove template. IF YOU HAVE DUCT BOARD: a. Mount the supplied metal mou
Inhaltszusammenfassung zur Seite Nr. 4
3. Remove base unit and cover from box. 4. Apply supplied “Duct Seal Kit” according to instructions included in kit. (See Figure 12) Figure 12 5. Determine whether to use flat or angled bracket. (Refer to UV-Aire Configurations in Section III for aid in this decision) a. Flat Bracket Installation i. Remove the two hex nuts and flat bracket from included bagged hardware. ii. Install the flat bracket and secure to the unit base with the hex nuts provided. (See Figure 13) Figure 13 b. Angl
Inhaltszusammenfassung zur Seite Nr. 5
8. Insert lamp through hole until lamp cannot be inserted any further. (See Figure 16) Figure 16 9. Swing swivel bracket over end of lamp. Hand-tighten the wing nut on stud. (See Figure 17) Be careful not to over tighten the wing nut. The porcelain at the lamp base may crack when over tightened. Figure 17 10. Plug ballast plug into end of lamp. (See Figure 18) Figure 18 11. Replace cover on unit. Tighten side screws. (See Figure 19 & 20) 12. Plug the power cord into a standard electrical
Inhaltszusammenfassung zur Seite Nr. 6
IV. BULB MOUNTING BRACKET SELECTION AND INSTALLATION TM The UV-AIRE units come with an angled mounting bracket and flat mounting bracket to position the bulb either straight or at an angle. Choose one or the other bracket method best suited for your needs. Refer to the configurations chart below when making your selection. UV-Aire™ Configurations Patent Pending 45° Installation Standard 90° Double Lamp Installation (Angled Bracket) Double Lamp Angle option allows longer lamps t
Inhaltszusammenfassung zur Seite Nr. 7
V. MAINTENANCE 1. Inspect and clean lamp at least every 6 months. 2. Replace your UV-Aire™ Air Purifying System lamp once a year to maintain the lamps maximum output intensity. The lamp should operate continuously for maximum lamp life and light effectiveness. VI. REPLACEMENT PROCEDURE VERY IMPORTANT: Turn switch on unit to ‘OFF’ position and unplug unit from outlet. 1. Loosen two side screws on unit. Remove cover. 2. Unplug ballast plug from end of lamp. 3. Remove wing nut on swivel bra
Inhaltszusammenfassung zur Seite Nr. 8
IX. FLEX DUCT INSTALLATION For installations on duct systems with a metallic main duct and flex duct branches, follow the instructions in figure 21 below. Figure 21 Limited Warranty Field Controls, L.L.C. warrants that the following Field Controls, L.L.C. products sold hereunder, shall be free from defects in material and workmanship under normal use for eighteen (18) months from date of manufacturing by the consumer excepting the provisions numbered below. UV-LAMPS/BULBS Field Controls, L
