Inhaltszusammenfassung zur Seite Nr. 1
10-TON LONG FRAME JACK
Model 66593
SET up ANd OpERATiNG iNSTRuCTiONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THiS MANuAL.
© ®
C
Inhaltszusammenfassung zur Seite Nr. 2
NOTiCE is used to SAVE THiS MANuAL Notice address practices Keep this manual for the safety not related to personal injury. warnings and precautions, assembly, CAuTiON, without operating, inspection, maintenance and CAuTiON the safety alert cleaning procedures. Write the product’s symbol, is used to address serial number in the back of the manual near practices not related to the assembly diagram (or month and year of personal injury. purchase if product has no number). Keep thi
Inhaltszusammenfassung zur Seite Nr. 3
b. Use safety equipment. Always wear d. Use the tool and its accessories in ANSI-approved safety impact gog- accordance with these instructions gles and heavy-duty work gloves. and in the manner intended for this Safety equipment such as non-skid particular type of tool, taking into ac- safety shoes, hard hat, or hearing count the working conditions, loca- protection used for appropriate con- tion and the work to be performed. ditions will reduce personal injuries. Use of this tool for op
Inhaltszusammenfassung zur Seite Nr. 4
5. Apply the vehicle’s parking brake 15. Do not use the Jack with the vehicle’s and chock the non-lifted tires before engine running. When running, the raising the vehicle. vehicle’s engine produces carbon monoxide, a colorless, odorless, toxic 6. Lift the vehicle only by the fume that, when inhaled, can cause manufacturer-recommended lifting serious personal injury or death. points. 16. Always keep hands, fingers, and 7. Stay out from under the load while it feet away from all moving
Inhaltszusammenfassung zur Seite Nr. 5
Tool Set up SpECiFiCATiONS iMpORTANT: The Jack comes filled with Maximum Lifting Capacity 10 Tons (20,000 lb.) oil. But the hydraulic system must be Minimum Lift Height 6-1/4" bled prior to initial use. (See Bleed- Maximum Lift Height 22-1/8" ing Instructions Pg. 8.) Net Weight 326.30 lbs 1. Make sure the vehicle is parked on a Jack Handle 36-1/4"L flat, level, solid, ground surface. Wheels and Casters All steel 2. Turn off the vehicle’s engine. Place the vehicle’s transmission in “P
Inhaltszusammenfassung zur Seite Nr. 6
one wheel and frame lifting points when lifting the entire front or rear Positioning end of the vehicle.) Holes Handle Lever positioning: 1. Moving the Valve Release Lever (1.4) to the desired position. (See Fig. 2.) Foot Pedal Position B Position A (2.1) Valve Release Lever Fig 3 Position D c. position C: Allows the Deflector Rod to drop into one of three holes Position C (See Fig. 3.) locking the Handle (1.5) Fig 2 in one of three angles, vertical, hori- zontal and 45°. a. positi
Inhaltszusammenfassung zur Seite Nr. 7
sition C. The Handle is less likely to To lower the vehicle: be in the way, be a tripping hazard, 1. When the work to the vehicle is com- and the upright Handle (2.5) can pleted, and prior to lowering the ve- be used to maintain balance while hicle, make sure to remove all tools, pumping the Foot Pedal (2.1). old vehicle parts, etc. from under the 2. Pump the Foot Pedal (2.1) until vehicle. the Saddle of the Jack has nearly 2. Pump Foot Pedal (2.1) to raise the reached the vehicle lif
Inhaltszusammenfassung zur Seite Nr. 8
BLEEdiNG iNSTRuCTiONS: just below the oil Filler Plug (9.1) orifice. 4. Thoroughly test the Jack for proper f. Pump the Foot Pedal (2.1) ten to operation prior to its actual use. If fifteen times in rapid succession. the Jack appears not to be working properly, it may be necessary to g. Top off the hydraulic oil if required. purge air from the hydraulic system. h. Clean off the Oil Filler Plug (9.1) with To do so: a clean cloth and thread back into a. Move Valve Release Lever to lo
Inhaltszusammenfassung zur Seite Nr. 9
pLEASE REAd THE FOLLOWiNG CAREFuLLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEM
Inhaltszusammenfassung zur Seite Nr. 10
ASSEMBLY diAGRAM SKU 66593 For technical questions, please call 1-800-444-3353. Page 10
Inhaltszusammenfassung zur Seite Nr. 11
pARTS LiST part description part description 1.1 Cap 4.11 Rivet 1.2 Compression Spring 1.3 Deflector Rod 5.1 Axle 1.4 Valve Release Lever 5.2 Nut 1.5 Handle (Control Rod) 5.3 Stop Ring 1.6 Washer 5.4 Wheel 1.7 Fastening Screw 5.5 Zerk Fitting 5.6 Roller 2.1 Foot Pedal 5.7 Stop Ring 2.2 Wire 5.8 Split Ring 2.3 Pin 2.4 Fork Member 6.1 Joint 2.5 Bushing 6.2 Screw 2.6 Base 6.17 Screw 2.7 Spring 6.18 Spring 2.8 Pin 2.9 Cap 7.1 Saddle 2.10 Shaft 7.2 Saddle Carrier 2.11 Screw 7.3 Axle 2.12 Washer 7.4 L
Inhaltszusammenfassung zur Seite Nr. 12
LiMiTEd 90 dAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
