Inhaltszusammenfassung zur Seite Nr. 1
RLC2626
Inhaltszusammenfassung zur Seite Nr. 2
Important Safety Instructions and Maintenance Important Safety Instructions CAUTION Risk of electronic shock, do not open. Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. High Voltage Refer all servicing to qualified service personnel. Do not open To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The apparatus shall not be exposed to dripping or splashing and no
Inhaltszusammenfassung zur Seite Nr. 3
Important Safety Instructions and Maintenance Important Safety Instructions To avoid the fire, no naked flame source, such as lighted candles, should be placed on the apparatus. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as co
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Instructions and Maintenance Installation Do not place the set on an unstable cart, stand, table or shelf. The set may fall, causing serious personal injury as well as damage to the product. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
Inhaltszusammenfassung zur Seite Nr. 5
Contents General description5 Specifications and accessories6 Overview7 Basic operation 10 External connection 12 Basic operation 14 Trouble shooting 23 Picture defects and countermeasures 24 Basic operation 4
Inhaltszusammenfassung zur Seite Nr. 6
General description Feature: l Zero X radiation complies to green environment protection requirement l Auto tuning and fine tuning l One composite video input socket (back) l One side composite video input socket l One S-Video input socket l One PC VGA input socket l One YPbPr input socket l One HDMI input socket (HDMI 1.3) l One AV output socket l Headphone l Multi-language OSD l Programmable TV sleep timer l No-signal automatic power off function l PC VGA mode: VGA, SVGA, XGA l YPbPr mode:
Inhaltszusammenfassung zur Seite Nr. 7
Specifications and accessories Specifications: Description RLC2626 1366X768 ~120V 60Hz 4WX2 74W 645X235X493mm TV with stand Dimensions (LXWXH) TV without stand 645X108X434mm TV with stand 7.2 Kg 6.4 Kg TV without stand Accessories: l User’s manual l Remote control l Wall-mounted accessories: Two wall-mounted brackets, four fixed screws and four fixed sleeves.(Optional) Note: 1.Due to TV may be used with different display screen, weight marked in this user's manual or in pack
Inhaltszusammenfassung zur Seite Nr. 8
Overview 1. Power indicator Green: Normal playing status. Red: Standby status. 2. IR remote sensor Point remote control at this sensor to conduct remote control. 3. VOL / Press these two buttons to increase or 2、 IR remote sensor 1、 Power indicator decrease the volume or operate menu. 4. PROG / Press these two buttons to select channel 7、 or operate menu. 5、 5. MENU 4、 Press this button to display OSD menu. 6. 3、 Press this button to enter standby m
Inhaltszusammenfassung zur Seite Nr. 9
Overview IN YPb/CbPr/Cr Connect to YPbPr/YCbCr video. AV AUDIO OUT Audio out for external devices. AV VIDEO OUT Video out for external devices. 8
Inhaltszusammenfassung zur Seite Nr. 10
Overview Remote control Loading batteries: 1) Remove the lid of the battery compartment. 2) Insert 2 size AAA batteries with polarities as indicated inside the compartment. 3) Replace the lid. Note: 1) One loading of batteries will last 1 year under normal use. 2) If you don’t intend to use the remote control for a long period of time, remove them to avoid damage due to leakage. 3) Do not mix old and new batteries, or different types. 4) Don’t throw the batteries into fire or water. 5) The ba
Inhaltszusammenfassung zur Seite Nr. 11
Basic operation Remote control introduction 1.INPUT Select input source. 2.POWER Turn your TV on and off. 3.0~9 Use these keys to input digit, letters and special characters. 4.INFO Displays the program information. 5.RECALL To swap to the previous program you wanted from current program. 6.SOUND Select audio mode. Press the key repeatedly to choose one of the modes among Normal, News, Music, Preference. 7.PICTURE Select picture mode. Press the key repeatedly to choose one of the modes among Nor
Inhaltszusammenfassung zur Seite Nr. 12
Basic operation (to be continued) 12.FREEZE No available for this model. 13.AV Swith to AV mode directly. 14.YPbPr Switch to YPbPr mode directly. 15.PC Switch to PC mode directly. 16.TV Switch to TV mode directly. 17.HDMI Switch to HDMI mode directly. 18. Press this button to shut off sound of the TV temporarily, press again to restore TV sound. 19.VOLq/p Press these buttons to adjust TV volume. 20.PROGq/p Press these buttons to change program upward or downward. 21.MENU Display the main menu. 2
Inhaltszusammenfassung zur Seite Nr. 13
External connection Antenna connection Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected to the antenna jack directly, if the antenna cable is a 300ohm flat feeder cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the antenna jack. l 75Ωcoaxial cable is recommended to eliminate interference and double image due to the unmatched input impedance of the antenna. l The antenna cable and power line should not be bundled togethe
Inhaltszusammenfassung zur Seite Nr. 14
External connection 2. How to assemble the stand? Before attaching/detaching the stand, make sure to turn off the TV. Before performing work spread cushioning over the base area to lay the LCD TV on. This will prevent it from being damaged. A. M4X8 screw B. Transition Board C. M4X8 screw D. Stand Figure2 Figure1 Figure3 Assembling instruction: 1.Unfasten screws A from the LCD TV. (Figure1) 2.Detach theTransition Board B from the LCD TV.(Figure1) 3.Fix the stand and the Transition Board toge
Inhaltszusammenfassung zur Seite Nr. 15
Basic operation (to be continued) Turning the TV On and Off 1. Insert the power cord plug into a AC outlet, the TV will enter standby mode.Press POWER button on the remote control to turn it on . The indicator will switch from red to green. 2. If you want to stop watching TV or go out for a while, you can press POWER button on the re- mote control. If you want to watch TV again, you can press this button again. 3. Unplug the power cord when the TV will not be used for a long period time. Aut
Inhaltszusammenfassung zur Seite Nr. 16
Basic operation (to be continued) 2) Press p/qArrow button to enter the submenu and press t/u Arrow button to select the language you desire. Selecting input source Press INPUT button on the remote control, then you can select input sources as following: TV AV1 AV2 S-VIDEO COMPONENT HDMI PC Setting color system In order to meet the color system in your country, you can set the color system as following: Press q/p Arrow button to select “COLOR SYSTEM” under “CHANNEL” menu
Inhaltszusammenfassung zur Seite Nr. 17
Basic operation (to be continued) 4) SKIP Press q/p Arrow button to select “SKIP”, then press t/u Arrow button to select “On” or “Off”. On: skip the channel; Off: not skip. 5) AFT Press q/p Arrow button to select “AFT”, then press t/u Arrow button to select “On” or “Off”. 6) FINE TUNE In case of bad image or sound of TV program, you can use Fine Tune function to obtain satisfied image or sound with operating steps as follows: Press q/p Arrow button to select “FINE TUNE” and press t/u Arrow b
Inhaltszusammenfassung zur Seite Nr. 18
Basic operation (to be continued) Adjusting the Picture Press MENU button on the remote control, then press t/u Arrowbutton to select “PICTURE” menu. PICTURE AUDIO SETTING FUNCTION CHANNEL PICTURE MODE PREFERENCE BRIGHTNESS 50 CONTRAST 50 COLOR 50 TINT 50 SHARPNESS 50 BACKLIGHT 50 COLOUR TEMP. STANDARD SCALE FULL MENU ADJUST SELECT EXIT 1) Adjusting Picture Mode Press q/p Arrow button to select “PICTURE MODE” , and press t/u Arrow button to adjust picture mode to your desire. Note: “BRIGHT
Inhaltszusammenfassung zur Seite Nr. 19
Basic operation (to be continued) Note: It is useless under no signal mode. Adjusting the Sound Press MENU button on the remote control, then press t/uArrow button to select “AUDIO ” menu. PICTURE AUDIO SETTING FUNCTION CHANNEL SOUND MODE PREFERENCE EQUALIZER 50 BALANCE AVL OFF MTS MONO ADJUST SELECT MENU EXIT 1) Adjusting Sound Mode Press q/p Arrow button to select “SOUND MODE”, use t/u Arrow button to adjust sound mode. 2) Adjusting the Equalizer Press q/p Arrow button to select “EQUALIZER”,
Inhaltszusammenfassung zur Seite Nr. 20
Basic operation (to be continued) 1) OSD Language Press q/p Arrow button to select “LANGUAGE” and press t/u Arrow button to select language you desire. 2) Adjusting SCREEN SAVER Press q/p Arrow button to select “SCREEN SAVER” and press t/u Arrow button to set screen saver. 3) Adjusting OSD Position Press q/p Arrow button to select “OSD Position” and press t/u Arrow button to set position of OSD. 4) Adjusting OSD Timer Press q/p Arrow button to select “DURATION”, Press t/u Arrow button to se
