Inhaltszusammenfassung zur Seite Nr. 1
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,AK-2W - LINEAR P/N: 222162 B - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - FOLDING: ALBUM-FOLD - BINDING: SADDLE-STITCH
AK-2W
Weather Resistant
Digital Keyless
Entry System
Installation and Programming Instructions
(760) 438-7000
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
www.linearcorp.com
222162 B IMAGE 1
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS FEATURES COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ✓ WEATHER RESISTANT DESIGN WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 or outdoor installation INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ✓ KEYPAD PROGRAMMABLE Opening the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 3
COMPONENT LOCATIONS MASTER CODE RED/GREEN YELLOW RESET JUMPER POWER/ACCESS "LOCKOUT" (JP2) INDICATOR INDICATOR TERMINAL BEZEL BLOCK #2 (TB2) SOLID STATE WHITE LED DOWN LIGHT TERMINAL BLOCK #1 (TB1) FACEPLATE KEYPAD BEEPER MOUNTING LEVEL PLATE JUMPER (JP1) Figure 1. Component Locations WIRING DIAGRAM TYPICAL DOOR INSTALLATION WIRING AK-2W TERMINALS TERMINAL TERMINAL BLOCK 2 BLOCK 1 12-24 VOLT 1 - AC OR DC SENSE - 8 POWER N.C. DOOR AC OR DC SUPPLY SWITCH 2 - AC OR DC COM - 7 POWER 3 - N.O. REQUEST
Inhaltszusammenfassung zur Seite Nr. 4
Final Keypad Installation INSTALLATION After wiring the keypad (see next page), complete the installation Before installing the keypad, the unit must be partially disassembled by securing the keypad to the mounting plate. to access the mounting plate. ❑ If a lower beeper sound level is required, before installing Opening the Keypad the keypad, remove Jumper JP1 (place the jumper block on The keypad assembly is secured with two tamper-resistant screws. one pin to save the jumper). Refer to
Inhaltszusammenfassung zur Seite Nr. 5
Keypad Wiring 2 WIRES See Figure 7 for an example of a basic door installation. The DOOR FOR DOOR SENSE keypad is mounted adjacent to the door. An electric door strike SENSE SWITCH is mounted in the door jamb to release the door lock. A magnetic SWITCH switch is mounted on the top of the door jamb for detecting when the door is open. Use the following steps to wire the keypad. Refer to the wiring 2 WIRES diagram shown in Figure 8 to assist in the wiring. AK-2W FOR DOOR ☞ NOTE: Up to 500 feet
Inhaltszusammenfassung zur Seite Nr. 6
FACTORY DEFAULTS Adding a New Entry Code MASTER PROGRAMMING CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123456 Press: 0 1 # Code # Code # Relay # ENTRY CODE LENGTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DIGITS Code = The new entry code: 1-999999, depending on code length REQUEST-TO-EXIT OUTPUT RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAIN RELAY Relay = Relay output entry co
Inhaltszusammenfassung zur Seite Nr. 7
Program all normal entry codes to use the Main Relay (Relay #1), Select Keypad Active Output Default: No Output and only Relay #1 as the output relay. Program the code(s) that Sets which output activates when any keys are pressed. This output is timed. If you want to use to hold the output for an indefi nite period to the toggle mode is selected for the output, the timer value defaults to 2 seconds. Auxiliary Relay (Relay #2). See the following example that sets entry codes 1234 for normal a
Inhaltszusammenfassung zur Seite Nr. 8
AK-2W OPERATION Beep Sounds During Auxiliary Relay Default: No Selects whether or not the keypad beeps during Auxiliary Relay activation. Keypad users request access by entering their code. ❑ Users of the AK-2W have up to 40 seconds to key in their Press: 4 2 # Sound # entry code. Sound = 1 for Yes, = 0 for No ❑ Up to eight seconds are allowed between each keystroke. ❑ All digits of the entry code must be entered. Example: If the code is 0042, the user must enter Beep Sounds During Output #3
