Inhaltszusammenfassung zur Seite Nr. 1
www.collegehillshonda.com
Accessory Application Publications No.
AII 36587
REAR CAMERA
INSTALLATION
ATTACHMENT 2006-2008 RIDGELINE
Issue Date
(EX-L WITH NAVI)
INSTRUCTIONS
MAY 2007
PARTS LIST Template
Attachment Kit
P/N: 08B21-SJC-102
Rear camera trim
19 Wire ties
Rear camera bracket
10 Small wire ties
6 Wire ties with clip
Rear camera subbracket
6-Pin connector
Harness clamp bracket A
Grommet
Harness clamp bracket B
2 Clear adhesive tapes
Rear camera subharness
3 Blind nuts
© 2007 American Hond
Inhaltszusammenfassung zur Seite Nr. 2
www.collegehillshonda.com 2 EPT sealers TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver 10 mm Combination wrench Ratchet 4 Cushion tapes 10, 12 mm and 14 mm Socket Torque wrench File Isopropyl alcohol Shop towel 2 Socket bolts, 4 x 10 mm Tape measure Drill 3 mm, 8 mm, and 10 mm Drill bits Utility knife 3 Washer screws, 4 x 12 mm T40, and T50 Torx bit KTC trim tool Scissors Tape 2 Washer screws, 4 x 6 mm Electrical tape Wire 3 mm Hex wrench 7 Clips Illustration of the Rear C
Inhaltszusammenfassung zur Seite Nr. 3
www.collegehillshonda.com 3. Remove the fuel fill door release handle. Remove 5. Pull away the weatherstrip from the B-pillar lower the left front door sill trim (three clips and three trim panel. Remove the left seat belt lower anchor retaining tabs). bolt cover and remove the lower anchor bolt. Remove the left B-pillar lower trim panel by pulling out toward you as shown. RETAINING TABS • Seat belt anchor bolt torque: FUEL FILL DOOR RELEASE HANDLE 30 to 35 N·m (22 to 25 lbs) LEFT FRONT 3 CLIPS
Inhaltszusammenfassung zur Seite Nr. 4
www.collegehillshonda.com 7. Lift up the rear seats, and remove the rear seat 9. Remove the rear seat belt anchor bolt and eight under covers; seat anchor bolts. • Remove the right rear seat under cover (four • Seat belt anchor bolt torque: clips). 30 to 35 N·m (22 to 25 lbs) • Remove the left rear seat under cover (five clips). LEFT REAR SEAT CUSHION RIGHT REAR SEAT CUSHION RIGHT REAR 8 SEAT SEAT UNDER ANCHOR COVER REAR SEAT BOLTS BELT ANCHOR 4212362T BOLT LEFT REAR SEAT UNDER 4212342T 9 CLIPS
Inhaltszusammenfassung zur Seite Nr. 5
www.collegehillshonda.com 11. Remove the rear trim panel cover (eight clips and 14. Remove the left rear lower anchor bolt cover, and two retaining tabs). remove the left rear seat belt lower anchor bolt. • Seat belt anchor bolt torque: 2 RETAINING 30 to 35 N·m (22 to 25 lbs) TABS REAR TRIM PANEL COVER CLIP 6 CLIPS 2 CLIPS LEFT REAR LOWER ANCHOR BOLT COVER CLIPS LEFT REAR 4212381T SEAT BELT 4715611K LOWER LEFT REAR ANCHOR PILLAR BOLT LOWER TRIM 12. Remove the left rear seat belt upper anchor bol
Inhaltszusammenfassung zur Seite Nr. 6
www.collegehillshonda.com 17. Remove the rear bumper: • Using a KTC trim tool, carefully pry up the front of the trim to release the three front clips. • Remove the license plate (two bolts). Start with the left clip and work towards the right clip. • Remove two bolts, six self-tapping screws and six clips from the rear bumper. • Gently left the front of the trim to release the four rear clips. • Pull the rear bumper toward you. Unplug the two vehicle connectors, and remove the rear bumper. 7 CL
Inhaltszusammenfassung zur Seite Nr. 7
www.collegehillshonda.com 19. Remove and discard the grommets from the roof 21. Remove the left C-pillar outer trim (slide panel, and install the six oval grommets and one rearward, and unplug the vehicle connector). round grommet into the roof panel. Remove the clips from the body, and reinstall the clips to the left C-pillar outer trim. GROMMET ROUND (Discard.) GROMMET 3 CLIPS (Install.) ROOF PANEL 3 CLIPS (Remove.) LEFT C-PILLAR 6 OVAL OUTER TRIM VEHICLE PANEL GROMMETS LEFT C-PILLAR VEHICLE O
Inhaltszusammenfassung zur Seite Nr. 8
www.collegehillshonda.com 23. Remove the front bed panel (six TORX bolts). 25. Remove the left lower bed light (one self-tapping screw, pull the light out towards you and unplug the vehicle connector). LEFT LOWER BED LIGHT SELF-TAPPING SCREW CLIP VEHICLE CONNECTOR FRONT BED LEFT REAR PANEL ANCHOR T50 TORX 6 T40 TORX BOLT 3929032H BOLTS 24. Remove the left bed rail trim: • Remove the screw cover (four retaining tabs). 3926062H • Remove the self-tapping screw. • Pull the left bed rail trim back to
Inhaltszusammenfassung zur Seite Nr. 9
www.collegehillshonda.com 28. Remove the tailgate trim: 30. Get the template. Using a scissors, cut out the marked area from the template. Align the edge of • Remove the four screws and release the one the template with the edge of the tailgate as end clip on each side. shown, and attach it to the tailgate tape. • Sharply push the tailgate to the right to release the 16 clips from the trim. OUTER TAILGATE • Remove the 16 clips from the tailgate and CUT reinstall the 16 clips to the tailgate trim
Inhaltszusammenfassung zur Seite Nr. 10
www.collegehillshonda.com 32. Drill three 8 mm holes and one 10 mm hole in the 34. Remove the four screws from the rear camera. tailgate. Route the rear camera harness through the rear camera subbracket, and install the rear camera • Wrap tape around a 3 mm drill bit, and 8 mm subbracket to the rear camera with the four drill bit and a 10 mm drill bit 10 to 15 mm from screws. the end or use a drill stop. • While wearing eye protection, drill a 3 mm REAR hole, then an 8 mm hole in all four locati
Inhaltszusammenfassung zur Seite Nr. 11
www.collegehillshonda.com 36. Route the rear camera harness through the 10 mm 38. Align the two locating tabs on the rear camera hole in the tailgate, and seat the grommet into the subbracket with the slots in the rear camera 10 mm hole. bracket, and install two 4 x 6 mm washer-screws. NOTE: Make sure the flat surface of the rear camera 10 mm subbracket is facing up: otherwise, the camera view HOLE will be upside down. REAR CAMERA HARNESS 4 x 6 mm REAR CAMERA WASHER BRACKET SCREW GROMMET WIRE 2
Inhaltszusammenfassung zur Seite Nr. 12
www.collegehillshonda.com 39. Install clear adhesive tapes to the tailgate: 40. Route the rear camera harness along the tailgate as shown. • Open the tailgate. • Get the clear adhesive tapes. Using scissors, cut 30 mm from the end of each adhesive tape. • Using isopropyl alcohol on a shop towel, clean REAR CAMERA HARNESS the tailgate where the adhesive tapes will attach. TAILGATE REAR TAILGATE 4708092K 41. Remove the TORX bolt from the tailgate hinge, and REAR attach the harness clamp bracket B
Inhaltszusammenfassung zur Seite Nr. 13
www.collegehillshonda.com 42. Secure the rear camera harness to the harness 45. Pull the rear camera harness out from the inside clamp bracket B with three small wire ties. Attach of the tailgate, and secure the rear camera the wire tie over the tape attached to the harness to the harness clamp bracket A with one harness. small wire tie. TAIL T50 TORX BOLT GATE HARNESS (Torque to 29 to32 N·m) CLAMP BRACKET B T50 TORX REAR BOLT CAMERA (Torque to HARNESS 29 to32 N·m) REAR CAMERA SMALL HARNESS WIRE
Inhaltszusammenfassung zur Seite Nr. 14
www.collegehillshonda.com 48. Secure the rear camera harness to the tailgate 51. Route the rear camera harness out through the with five wire ties with clip. bed panel hole, and secure the rear camera harness to the vehicle harness with one wire tie just inside the panel hole. 5 WIRE TIES WITH CLIP TAILGATE BED PANEL HOLE TAILGATE REAR REAR CAMERA HARNESS WIRE TIE FRONT VEHICLE HARNESS CUSHION TAPE REAR CAMERA (Cut in half.) 4708103K HARNESS 49. Using isopropyl alcohol on a shop towel, clean th
Inhaltszusammenfassung zur Seite Nr. 15
www.collegehillshonda.com 53. Remove the vehicle grommet from the left 56. Inside the passenger’s compartment turn down the C-pillar. rear panel insulator. Pull the rear camera harness out from the hole in the C-pillar, and remove the tape and wire from the rear camera harness. LEFT C-PILLAR BED BULKHEAD REAR CAMERA VEHICLE HARNESS GROMMET VEHICLE PANEL OPENING OPENING VEHICLE GROMMET FRONT WIRE TAPE WIRE 6-PIN 6-PIN REAR CONNECTOR CONNECTOR CAMERA LOCK Harness side HARNESS view 6 TERMINALS REAR
Inhaltszusammenfassung zur Seite Nr. 16
www.collegehillshonda.com 60. Continue routing the rear camera subharness 62. Plug the rear camera subharness 6-pin connector forward along the vehicle harness, and secure into the Navi control unit. the subharness to the vehicle harness with four small wire ties. NAVI CONTROL UNIT DRIVER’S SEAT VEHICLE HARNESS REAR CAMERA SUBHARNESS REAR CAMERA FRONT SUB HARNESS 4713030K 6-PIN CONNECTOR 63. Slide the driver’s seat back and forth to check that the rear camera subharness is not pulled too tight
Inhaltszusammenfassung zur Seite Nr. 17
www.collegehillshonda.com 64. Reconnect the negative cable to the battery. Turn 68. Measure and mark the rear bumper at the location the key to the ON (II) position, and enter the Navi shown. code. 2 4 x 6 mm REAR WASHER SCREWS BUMPER REAR CAMERA Adjust the angle. REAR CAMERA TRIM 10 mm 15 mm 3 mm Cut off. 4N15011K REAR CAMERA BRACKET 69. Using a utility knife, cut and remove measured piece from the rear bumper. Remove any burrs 5D10060T from the cut area with a file. 4 x 10 mm SOCKET BOLTS 70.
