Bedienungsanleitung Audiovox Prestige 128-8602

Inhaltszusammenfassung zur Seite Nr. 1

Model APS-45N
Installation Manual
Keyless Entry System
With Two Auxiliary Outputs
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems Only.
Kit Contents:
 (1) Control Module
 (2) - Four Button Transmitters
 4 Channel Code Learning Receiver
 On Board Antenna
 (1) - Multi Pin Input/Output Harness
 (1) - Three Pin Door Lock Harness
 (1) - Two Pin LED Indicator
 (1) - Two Pin Valet / Override Switch
 (1) - 15 Amp In-l

Inhaltszusammenfassung zur Seite Nr. 2

This Keyless Entry System is designed to provide a convenient electronic means to gain access to the vehicle by providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the vehicle's dome lights, as well as exterior parking lights. Although not an alarm system, this unit also incudes a starter interrupt circuit output. It also includes two additional auxiliary outputs designed to allow for control over optional devices such as a power tr

Inhaltszusammenfassung zur Seite Nr. 3

directly to the vehicle's positive parking light circuit. Once the wire is located, confirm that all the vehicle's parking lights will illuminate when +12VDC is connected to it. NOTE: Some vehicles, (mostly European) have isolated "left" and "right" side parking lights. To connect to the parking light systems in these vehicles, you must use separate SPDT relays to connect to each side in order to keep them isolated. Attach the WHITE wire of the system to this point. BROWN Wire: Negative (-) D

Inhaltszusammenfassung zur Seite Nr. 4

GREEN/BLACK Wire: Immediate, 300mA Duration of Transmit, Channel 3 OutputThe Green/Black wire supplies a 300mA switched output whenever Channel 3of the receiver is accessed. Pressing A combination of thetransmitter Lock/UnLock buttons simultaneously will access Channel 3 and will remain active for as long as the transmitter button(s) is held. This is a low current output and must be connected to a relay to supply power to the device you intend to control. Connect Green/Black Trace wire to t

Inhaltszusammenfassung zur Seite Nr. 5

the red wire to the wire that provides a low current positive signal from the factory door unlock switch to the factory door lock control relay. The green wire provides a positive pulse during locking, or the pulsed + 12 volt lock output. Connect the green wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door lock control relay. 3 Wire Positive Switched 2 Step Door Locks The green wire provides a positive pulse during locking, or the p

Inhaltszusammenfassung zur Seite Nr. 6

Programmable Features: Features 1 Chirp 2 Chirp 3 Chirps Default First Passive Arming Active Arming Active Arming Second Ignition D/L ON Ignition D/L OFF Ignition D/L OFF Third Ignition D/UL ON Ignition D/UL OFF Ignition D/UL OFF Fourth Chirps ON Chirps OFF Chirps ON Fifth Passive D/L Active D/L Active D/L Sixth Siren Output Horn Output Horn Output Seventh 800ms D/L Pulse 3.5 Sec. D/L Pulse 800ms D/L Pulse 800ms Door Lock Double 800ms D/UL Pulses To Program These Features: Entering the Programmi

Inhaltszusammenfassung zur Seite Nr. 7

Fourth Turn the valet switch on then off 1 chirp = chirps on 4 Flash pause Press transmitter Lock button to change 2 chirps = chirps off or Fifth Turn the valet switch on then off 2 chirps = active locks 5 Flash pause Press transmitter Lock button to change 1 chirp = passive locks or Sixth Turn the valet switch on then off 2 chirp = horn output 6 Flash pause Press transmitter Lock button to change 1 chirp = siren output or Seventh Turn the valet switch on then off 1 chirp = 800ms door lock outpu

Inhaltszusammenfassung zur Seite Nr. 8

© 2009 Audiovox Electronics Corp. 128-8602 128-8602 8 of 8