Inhaltszusammenfassung zur Seite Nr. 1
OWNER'S MANUAL
76CM CORDLESS REMOTE LCD TV/MONITOR
MODEL: TFTV-760
Type Tested
Electrical
Safety
AS/NZS 3250 Lic 3250
Standards Australia
APP No: N17339
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Inhaltszusammenfassung zur Seite Nr. 2
Contents Congratulations on your purchase of this Palsonic LCD TV/MONITOR. We recommend that your thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this LCD TV/MONITOR. Retain this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual ones for better visibility. Contents ........................................... 1 Channel edit ...............................
Inhaltszusammenfassung zur Seite Nr. 3
Important Safety Cautions When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. Water and moisture - Do not use this product near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. Do not use immediately after moving from a low temperature to high temperature environment, as this causes condensation
Inhaltszusammenfassung zur Seite Nr. 4
This TV set can be operated on a power of ~240V 50Hz. You must not use a power supply of any other type. When relocating the product placed on a trolley, it must be moved with the utmost care. Sudden stops, excessive force and uneven floor surfaces can cause the product to fall from the trolley. The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product. Power supply cords should be routed so that they
Inhaltszusammenfassung zur Seite Nr. 5
Identification of controls Front Remote sensor Indicator To enter into MENU Channel up Volume up Volume down Channel down Power on/Standby To select input signal 4
Inhaltszusammenfassung zur Seite Nr. 6
Back S-VIDEO VGA ANT IN PHONE LINE IN Pr L L VIDEO Y Cb Cr Y Pb R R + - + - R L HDTV Video VGA input Antenna input Audio inputs Earphone input jack HDTV YPbPr S-video input PC audio DC input inputs line in Speaker HDTV Audio inputs DVD inputs outputs 5
Inhaltszusammenfassung zur Seite Nr. 7
Identification of controls (continued) Remote Control POWER Power on/Standby Sound Mute Channel up CH VOL VOL Volume down Volume up - + CH Channel down MENU ENTER To enter into MENU To exit OSD menu C.SYS ZOOM CLK SLP Colour/Sound Sleep timer system select Zoom select AUTO.ADJ P.M DSP Clock/Timer setting Auto correct picture Previous channel Picture mode select On-screen display 1 2 3 4 5 6 Channel select 7 8 9 Input signal select -/ AV -- 0 OSD STILL Bass+ Treb+ POSITION Still picture Bass - Tr
Inhaltszusammenfassung zur Seite Nr. 8
Battery installation Effective remote range Please install the batteries before using the remote control unit. Open the battery cover. 5m POWER CH VOL VOL - + CH MENU ENTER C.SYS ZOOM CLK SLP AUTO.ADJ P.M DSP 1 2 3 4 5 6 Install two "AAA" batteries 7 8 9 AV 0 -/-- OSD STILL POSITION Bass+ Treb+ matching the +/- Bass - Treb- polarities of the battery to the +/- marks. Notes: There should be no obstacle between the TV and the transmitter. Use the remote control within the effective Replace the bat
Inhaltszusammenfassung zur Seite Nr. 9
Installation Antenna installation/Adaptor connection Before using this equipment, please connect the AC power adaptor correctly. Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. AC power adapter Notes: Turn off the power firstly when you connect a outdoor antenna to the Antenna input terminal. When installing an outside antenna system, extreme care sho
Inhaltszusammenfassung zur Seite Nr. 10
Connecting video/audio equipment S-VIDEO VGA ANT IN PHONE LINE IN VIDEO Y Cb Cr Y Pb Pr R L R L + - + - L R Y Yellow (video) W White (audio L/MONO) R Red (audio R) To S-video R W To audio Y R W input inputs To audio To video inputs input To audio W R outputs To audio To video outputs output Video equipment W R Y with S-video terminal To ANT output Video equipment without S-video terminal To ANT output 9 To ANT input
Inhaltszusammenfassung zur Seite Nr. 11
Installation (continued) Connecting DVD Player and speakers S-VIDEO ANT IN LINE IN VGA PHONE VIDEO Y Cb Cr Y Pb Pr R L R L + - + - R L HDTV Red Black Red To YCbCr To audio B G R R W inputs inputs To speaker To YCbCr To audio outputs outputs G B R W R DVD Player W White (audio L/MONO) R Red (audio R, Cr) G Green (Y) B Blue (Cb) 10 To speaker
Inhaltszusammenfassung zur Seite Nr. 12
Connecting YPbPr terminals S-VIDEO ANT IN LINE IN VGA PHONE VIDEO Y Cb Cr Y Pb Pr R L R L + - + - R L HDTV To YPbPr To audio B R G R W inputs inputs To YPbPr W White (audio L/MONO) To audio B R R W G outputs outputs R Red (audio R, Pr) G Green (Y) B Blue (Pb) SET TOP BOX (Or other equipment with YPbPr output terminals) 11
Inhaltszusammenfassung zur Seite Nr. 13
Installation (continued) Connecting VGA interface S-VIDEO ANT IN LINE IN VGA PHONE VIDEO Y Cb Cr Y Pb Pr R L R L + - + - R L HDTV To LINE in To VGA input interface Equipment with VGA output interface To LINE out To VGA output interface 12
Inhaltszusammenfassung zur Seite Nr. 14
Elevation adjustment You can adjust the angle of the LCD TV/Monitor as follows. 0 0 The elevation can be adjusted from -5 to +10 . 0 10 0 -5 13
Inhaltszusammenfassung zur Seite Nr. 15
There are four pages of MENU in TV, PC and YPbPr mode. In MENU operations, the CH / buttons are used to select item upwards or downwards; the VOL+/- buttons are used to adjust or confirm selected item. Menu Introduction Press MENU button in TV mode PICTURE SETTING To adjust the picture's brightness. - + 50 Brightness - 50 + Contrast To adjust the picture's contrast. - + 50 Color - 50 + Sharpness To adjust the picture's colour saturation. - + 50 Tint To adjust the picture's sharpness. o
Inhaltszusammenfassung zur Seite Nr. 16
To adjust picture's brightness and contrast in Press MENU button in PC mode PC mode. (not affect picture in TV or AV mode) PICTURE SETTING - + 25 Brightness - + 25 Contrast If the best picture can not be obtained after many - + 25 Phase times of auto correction, you can adjust these two - + 25 Frequency items to obtain the best picture. - + 25 USER_R - + 25 USER_G - + 25 USER_B Only when the "Color temp" is set to "User", Color Temp 9300K these three items are adjustable. or V+> key to cha
Inhaltszusammenfassung zur Seite Nr. 17
Turning On/Off Turning On 1. Insert the output plug of the AC power adaptor into the DC power input of the unit. 2. Press the power switch on AC power adaptor and the red indicator lights up, the TV/Monitor is in STANDBY mode. 3. Press the POWER button on the unit's control panel or the button on the remote control to turn on. POWER Notes: In TV mode, when there is no TV signal input for about 15 CH minutes, the set goes to STANDBY automatically. VOL VOL - + CH MENU ENTER Turning Off C.SYS Z
Inhaltszusammenfassung zur Seite Nr. 18
Channel Preset CHANNEL SETTING To enter into CHANNEL SETTING menu Auto search Search Fine Tune 1. Press MENU button repeatedly to display CHANNEL SETTING Change Prog Current Prog 12 menu. Change to Prog 15 Skip ON 2. Press CH or CH button to select item. 3. Press VOL+ or VOL- button to confirm or adjust selected item. or V+> key to change Auto Search Please enter into CHANNEL SETTING menu and select Auto Search POWER item. Press VOL- or VOL+ button to start Auto Search and all
Inhaltszusammenfassung zur Seite Nr. 19
Channel Preset (continued) CHANNEL SETTING Channel Skipping Auto search Search Fine Tune You can skip unnecessary channels by using Skip function when you Change Prog 12 Current Prog browse program by CH / buttons. 15 Change to Prog Skip ON / Use 0~9 digit buttons or CH buttons to select a unwanted channel firstly, then enter into CHANNEL SETTING menu and select Skip item. or V+> key to change Press VOL+/- button to select ON to skip this channel. Now this channel / will be s
Inhaltszusammenfassung zur Seite Nr. 20
Channel Select Use 0~9 digit buttons and -/-- button 8 Use 0~9 digit buttons to select one-digit channel number. Press -/-- button Press 0-9 direct - 8 to display "-". channel selector. POWER To select two-digit channel: CH Press -/-- button Press 1-9 Press 0-9 -1 - - 18 VOL VOL repeatedly to buttons. buttons. - + display "--". CH MENU ENTER C.SYS ZOOM CLK SLP To select three-digit channel: AUTO.ADJ P.M DSP Press -/-- button Press 1-9 Press 0-9 Press 0-9 --- 180 --1 -18 repeatedly to buttons. bu
