Inhaltszusammenfassung zur Seite Nr. 1
FAQs
Insignia 32” LCD HDTV 720p (NS-LCD32-09)
September 30, 2008
My picture is not filling the screen. I have black bars around my picture.
• This is due to the aspect ratio. An increasing amount of digital TV programming and movies are presented in wide
screen (16:9).
• To change the appearance of the screen, cycle through these four options by pressing the Zoom button on the remote:
o Normal: Selects the aspect ratio that matches to source’s aspect ratio (4:3 or 16:9)
o Wide: Dis
Inhaltszusammenfassung zur Seite Nr. 2
I am programming my universal remote, what code is needed? • Please use the Insignia universal remote code website to determine the universal remote code you need: www.insignia-products.com/universalcontrolcodes.aspx I am receiving the error message “No Signal.” • Make sure that your cable is properly plugged into your TV and the source device. • Press INPUT and make sure you have selected the correct input for the device or service you are trying to use. • Are you using a cable/sat
Inhaltszusammenfassung zur Seite Nr. 3
I have poor picture quality. • Make sure your cable connections are connected securely. • If you are receiving service from a cable or satellite provider, reception can vary by channel depending on the broadcast power level of a given station. Contact your cable or satellite provider. • If you are using an antenna, the signal strength of the channel may be low. o Check the signal strength of the channel (Please note that the signal strength is only displayed on digital channels): Pr
Inhaltszusammenfassung zur Seite Nr. 4
• Press EXIT to close the Manual Channel Set menu. Reception can vary by channel depending on the broadcast power level of a given station. Contact your cable provider. o If you are using an antenna: Try running an autochannel search: • Press MENU. The on-screen menu opens. • Press ^ or v to select Setup, then press > to enter Setup menu. • Press ^ or v to select Tuning Band, then press > to select Air. • Press ^ or v to select Auto Ch Search, then press > to begin searching for c
Inhaltszusammenfassung zur Seite Nr. 5
o Use a basic indoor set-top antenna designed to pick up both VHF and UHF. OR Use a set-top antenna that has a built-in signal amplifier. OR Use an antenna mounted on your roof or in your attic. o For more information about antennas and the available channels in your area, visit www.antennaweb.org. Press EXIT to close the Signal Level display. o The UHF band (channels 14 and higher) is more directional than VHF (channels 2-13) and more sensitive to obstacles (such as trees, ta
Inhaltszusammenfassung zur Seite Nr. 6
Select and click on Control Panel. Click on Appearance and Themes. Click Personalization. Click Display Settings. Select Monitor 2. Drag the screen resolution slider to the left to decrease the resolution of your monitor, making text and pictures appear larger or drag the slider to the right to increase the resolution of your monitor, making text and pictures appear smaller. Click Apply to have the new resolution take effect. • If the Monitor Settings dialog box appears, look
Inhaltszusammenfassung zur Seite Nr. 7
• If the Monitor Settings dialog box appears, look at your display. If you like the new resolution, click Yes. If you do not like the resolution, click No and adjust the resolution using the screen resolution slider. • Click OK. In classic view: • Double-click Display. • In the Display Properties dialog box, click on the Settings tab. • Select monitor 2. • Drag the screen resolution slider to the left to decrease the resolution of your monitor, making text and pictures appear larg
Inhaltszusammenfassung zur Seite Nr. 8
I have sound but no picture. • You may have accidentally turned the picture off. o Press MENU. The on-screen menu opens. o Press ^ or v to select Audio, then press > to enter Audio menu. o Press ^ or v to select Audio Only, then press < or > to select Off. • Make sure the cables are connected correctly and securely. • The video cable(s) you are using may be bad, try a new set. • If you are using an antenna, the signal strength of the channel may be low. o Check the signal strength
Inhaltszusammenfassung zur Seite Nr. 9
o Are you using a cable/satellite box, cable connected directly to the TV, or an antenna? If you are using a cable or satellite box you must use the remote that came with that box to change channels. • Make sure you have the correct input selected to view channels via the cable or satellite box. For example, if the cable or satellite box is connected via component cables please press input and select Component 1 or Component 2 to view your channels. If you are using cable connected
Inhaltszusammenfassung zur Seite Nr. 10
• The base is attached via 4 screws that can be found on the back of the TV directly above the base. o Lay the TV face down on the edge of a table or work bench. Make sure to put your TV on a cushion or soft covering to prevent damaging the case or screen. o Remove the 4 screws that secure the stand column to your TV. o Slide the stand away of the TV. How do I get headphones to work with my TV? • Connect the headphones cable to the headphone jack on the side of your TV. • A headpho
