Inhaltszusammenfassung zur Seite Nr. 17
OSD Menu 5. Lock menu You must enter the password to gain access to the Lock menu. The default password is 0000. You may modify the following options: Description Change password: Change the password, you must enter the new password twice to confirm it. Note: Do not forget the password. System Lock: Allow you to turn on or off the system lock. If deactivated, the functions described below don’t work. This option menu allows you to lock any TV channel or adjust the Movie rating filter. US: TV: U
Inhaltszusammenfassung zur Seite Nr. 18
OSD Menu 6. Channel menu Description Air/Cable: Allow you to select antenna between Air and Cable. If you selet “Cable”, the following items(Favorite, Show/Hide, Channel NO, Channel Label and DTV Signal) are unable to use. Auto Scan: Enter the Auto Scan menu to start auto scan. If you select “Cable” as input signal in Antenna item, allows you to select Cable System among: Auto, STD, IRC and HRC. Use button to highlight the “Start to Scan”, then press button to search the channels automa
Inhaltszusammenfassung zur Seite Nr. 19
OSD Menu Show/Hide: Allow you to show or hide the channels. Use / button to highlight the desired item, then press OK button to show or hide the highlighted channel. Channel No.: Show and select the channel. Channel Label: Allow you to setup a label for the channel. Press / button to select the position of the table, and press / button to select the words. DTV Signal: Show the quality of digital signal: good, Normal, Bad. 17
Inhaltszusammenfassung zur Seite Nr. 20
Simple Troubleshooting Simple Troubleshooting If the display fails or performance dramatically deteriorates check the Display in accordance with the following instructions.Remember to check the peripherals topinpiont the source of the failure. If the display still fails to perform as expected,connect your helpline for assistance. No power - Check all connections to the TV. - Press either the power button or the Standby button on the Remote control. No picture or sound - Ensure that the TV is p
Inhaltszusammenfassung zur Seite Nr. 1
32” LED Television
MODEL: RLED3218A
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Caution Contents Caution 2 Safety Information 3 Unit and Accessories 4 Introduction 5-9 1. Front View 5 2. Rear View 6 3. Instruction for Wall Mount 7 4. Remote Control 8-9 Basic Operation 10 OSD Menu 11-17 1. Picture menu 11 2. Audio menu 12 3. Time menu 13 4. Setup menu 14 5. Lock menu 15 6. Channel menu 16-17 Simple Troubleshooting 18 19-20 1
Inhaltszusammenfassung zur Seite Nr. 4
Caution Caution is intended to alert the user to the presence of un-insulated "dangerous to constitute a risk of electric shock to the persons. The exclamation point within an equilateral triangle is intend to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Correct disposal of this Product (Waste Electrical & Electronic Equipment (WEEE) Your product is designed and manufactured with high quality mater
Inhaltszusammenfassung zur Seite Nr. 5
Safety Information Safety Information Electrical safety Physical safety 3
Inhaltszusammenfassung zur Seite Nr. 6
Unit and Accessories Unit and Accessories INPUT 123 456 789 0 -/-- PICTURE SOUND SLEEP DISPLAY VOL+ CH+ MUTE VOL- CH- EXIT MENU OK CC MTS EPG FAV TV set Remote control Batteries: 2xAAA Instructions for fixing stand Instructions for User's manual fixing stand 4
Inhaltszusammenfassung zur Seite Nr. 7
INPUT MENU CH+ CH- VOL+ VOL- POWER Introduction Introduction 1. Front View Led Indicator Remote Control window (Keep clear) 1). (IR) Infrared Receiver: Receives IR signals from the remote control. (Power on/Standby)LED Indicator: Press POWER to turn on and off. Indicator on(Red) Standby mode Indicator on(Green) Power on mode The effective receiving range for the signal is 5-8 metres from the front of the remote 0 0 contro
Inhaltszusammenfassung zur Seite Nr. 8
Introduction 2. Rear View Service HDMI1 HDMI2 HDMI3 AC POWER IN Service HDMI1 HDMI2 HDMI3 AC POWER IN: Connect to an earth 100-240V~ 50/60Hz outlet with the Power Cable. Service : For service use only. : Connect it to the HDMI of DVD or other equipment. HDMI1/2/3 Headphone out : Connect it to your headphone or other audio equipments. COAX : Digital coaxial output. : Connect antenna or cable 75 Ohm coaxial to receive TV signal. RF : Connect them to audio output terminal
Inhaltszusammenfassung zur Seite Nr. 9
Introduction 3. Instruction for Wall Mount The wall mount kit (not included) with your purchase allows you to mount your RCA TV on the wall. For detailed information on installing the wall mount, refer to the instructions provided by the wall mount manufacturer. It is strongly recommended to contact a technician for professional assistance for wall mount installation. RCA is not responsible for any damage to the product or injury to yourself or others resulting from the wall-mounting. Dimen
Inhaltszusammenfassung zur Seite Nr. 10
Introduction 4. Remote Control The remote control is using Infra-Red(IR). Point it towards the front of the LED TV. The remote control may not work correctly if it is operated out of range or out of angle. INPUT POWER(red button): Turn the TV on/standby. INPUT: Press to display the input source menu. Number Buttons: Choose channel directly. 123 Select channel 5, Press button "5"; Select channel 62, Press button "6", then press button "2" in 2 456 seconds; Select channel 151, Press button "1", a
Inhaltszusammenfassung zur Seite Nr. 11
Introduction Installing Batteries 1. Open the battery compartment cover on the back of the remote control. 2. Insert two 1.5V AAA size batteries observing the polarity markings inside the battery compartment. Don’t mix different types or used batteries with new ones. 3. Close the cover. 0 - The remote control should be operated within 30 feet(7m) and 30 to the left and right of the IR receive at the front of the LED TV. - Used batteries should be disposed properly. 9
Inhaltszusammenfassung zur Seite Nr. 12
Basic Operation Power on/off 1. -To turn on the Switch Press POWER button on the TV or remote control. -To turn off the TV Press POWER button on the TV or remote control. TV Input Source select AV Press INPUT button on the TV set or remote control to display input Component source menu, and use CH+/- button on the TV set or button HDMI1 HDMI2 on remote control to select the input source, press OK button on the HDMI3 remote control to enter. VGA Note: Before you select the i
Inhaltszusammenfassung zur Seite Nr. 13
OSD Menu OSD Menu 1. Picture menu Description Picture mode: Select between Standard, Dynamic, Mild, Sports User and Power Saving. You may select the picture mode directly by pressing the PICTURE button on the remote control. Note: when select the "Power Saving", the machine is in energy-saving status. Contrast: Control the difference between the bright and dark regions of the screen picture. Brightness: Adjust brightness of the picture. Color: Adjust color of the picture. Tint: Control the fres
Inhaltszusammenfassung zur Seite Nr. 14
OSD Menu 2. Audio menu 12 6 Setup Picture Audio Time Lock Channel Flat Sound Mode 50 Bass 50 Treble 50 Balance Surround Off SPDIF Type PCM Audio Language English Select Move MENU Exit Description Sound Mode: Select your desired picture mode as follow: Flat, Music, Movie, Sports and User You may select the sound mode directly by pressing the SOUND button on the remote control. Bass: Low frequency intensity. Treble: High frequency intensity. Balance: Left and right stereo audio channels balance. S
Inhaltszusammenfassung zur Seite Nr. 15
OSD Menu 3. Time menu Description Sleep timer: You may set the automatic shutdown timer choosing from 5 to 240 minutes, or deactivate this function. Time zone: Select between Pacific, Alaska, Hawaii, Eastern, Central and Mountain. Daylight Saving Time: Select between On and Off. Clock: User can not change time manually during DTV mode, for time is from signal source directly. 13
Inhaltszusammenfassung zur Seite Nr. 16
OSD Menu 4. Setup menu Description Menu Language: Select OSD menu language. Transparency: Turn on or off the transparency menu function. Zoom Mode: Select the zoom mode between 16:9, 16:9 zoom, 4:3, 4:3 zoom. Noise reduction: Select the noise reduction mode between Strong, Off, Weak and Middle. PC SETUP: If the video input signal comes from your PC, you may adjust the V-Position, H-Position, Clock, Phase or even perform an Auto adjustment. Closed Caption: CC Mode: Allow you to select the CC
