Bedienungsanleitung Toyota 99-8212

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-8212
APPLICATIONS
2004-2008 Toyota Solara
99-8212
KIT FEATURES
• DIN Head Unit Provisions with Pocket
• ISO DIN Head Unit Provisions with Pocket
KIT COMPONENTS
A) Radio Housing w/ Pocket • B) ISO Brackets
C) Radio Housing Brackets • D) (2) PTH-838 Phillips Screws • E) (8) PFH-614 Phillips Screws
F) Trim Plate • G) X-9002 Radio Support Bracket
D
E
C
A
B
F
G
TOOLS REQUIRED:
Socket Wrench • Small Flat Blade Screwdriver • Phillips Screwdriver

Inhaltszusammenfassung zur Seite Nr. 2

99-8212 Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 TABLE OF CONTENTS

Inhaltszusammenfassung zur Seite Nr. 3

DASH DISASSEMBLY 99-8212 2004-2008 TOYOTA SOLARA A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the cover from the hazard switch then unclip and remove the switch. (Figure A) B 3 Unclip and remove panel above radio including A/C vents and clock. TIP: Start pulling from the inside of the hazard switch cavity. (Figure B) Unclip and remove panel surrounding 4 shifter. (Figure C) C 5 Unclip and remove pocket and seat heater switch panel. (Figure D) 6 R

Inhaltszusammenfassung zur Seite Nr. 4

99-8212 2004-2008 TOYOTA SOLARA 1 Attach the corresponding radio housing bracket to the radio housing using the included (8) PFH-614 Phillips screws. 2 Slide the factory climate control into the assembled radio housing brackets/radio housing assembly and secure with the factory hardware. 3 Attach the radio support to the back of the pocket using the supplied (2) PTF- 838 Phillips screws. 2 KIT ASSEMBLY

Inhaltszusammenfassung zur Seite Nr. 5

KIT ASSEMBLY 99-8212 DIN HEAD UNIT PROVISIONS A 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket head unit into the cage and secure. (Figure B) B 3

Inhaltszusammenfassung zur Seite Nr. 6

99-8212 ISO DIN HEAD UNIT PROVISIONS A Mount the ISO Brackets to the head 1 unit with the screws supplied with the unit. (Figure A) Slide the head unit into the radio 2 opening until the side clips engage. (Figure B) B 3 Snap the trim plate into the radio housing. (Figure B) 4 KIT ASSEMBLY

Inhaltszusammenfassung zur Seite Nr. 7

FINAL ASSEMBLY 99-8212 A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the 1 dash. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit) Re-connect the negative battery terminal 2 and test the unit for proper operation. Reassemble radio and dash assemblies in 3 reverse order of disassembly. 5

Inhaltszusammenfassung zur Seite Nr. 8

INST99-8212 1-800-221-0932 www.metraonline.com Rev. 07-02-07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8212