Inhaltszusammenfassung zur Seite Nr. 1
LAMP
H/L
Horizon
HX350S
VHF/FM Marine
Handheld Transceiver
Owner’s Manual
HX350S Owner’s Manual page 23
16/9
A/B
WX
SCAN
MEM
SUBMERSIBLE
HX350S
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS GENERAL INFORMATION .................................................................................... 1 INTRODUCTION .................................................................................................... 1 FCC/ INDUSTRY CANADA INFORMATION .......................................................... 1 ACCESSORIES ...................................................................................................... 2 PACKING LIST ...................................
Inhaltszusammenfassung zur Seite Nr. 3
1 GENERAL INFORMATION 1.1 INTRODUCTION The Standard Communications Corp. (SCC) HX350S is a marine handheld two-way VHF transceiver. The transceiver has 65 channels: 55 marine and 10 weather. The 55 marine channels are switchable to comply with either USA, International, or Canadian regulations. It has an emergency channel 16 which can be immediately selected from any channel by pressing the red 16/9 key. Weather channels can also be accessed immediately by pressing the WX key. The transceive
Inhaltszusammenfassung zur Seite Nr. 4
2 ACCESSORIES 2.1 PACKING LIST When the package containing the transceiver is first opened, please check it for the following contents: • HX350S Transceiver • CBT350 Alkaline Battery Tray • CAW240 DC Charge Cable with 12 V Cigarette Lighter • CNB350/CNB350AS Rechargeable Battery Pack • CCA250 Charge Adaptor with screws • CWC230 120VAC Wall Charger for CCA250 • CAT350 Flexible Antenna with STUD connector • Lanyard • Belt Clip with screws • Owner’s Manual • Owner’s Manual Supplement 2.2 OPTIONS CM
Inhaltszusammenfassung zur Seite Nr. 5
3 CONTROLS AND INDICATORS NOTE This section defines each control of the transceiver. For detailed operating instructions refer to section 4 of this manual. Refer to Figure 1 for the location of the following controls, indicators, and connections. 3.1 CONTROLS AND CONNECTIONS q POWER SWITCH/VOLUME CONTROL Turns the transceiver on and off, and adjusts the volume. w SQUELCH CONTROL (SQL) Sets the point at which random noise on the channel does not activate the audio circuits but a received signal
Inhaltszusammenfassung zur Seite Nr. 6
16/9 WX A/B SPEAKER/MICROPHONE CONNECTOR ANTENNA CONNECTOR OFF SQL VOL SQUELCH POWER SWITCH CONTROL VOLUME CONTROL LAMP/ KEY LOCK KEY LAMP SCAN KEY WX KEY UP KEY 16/9 KEY H/L PTT SWITCH DOWN KEY A/B KEY H/L KEY MEM KEY SUBMERSIBLE BATTERY PACK Figure 1. Controls and Connectors page 4 Owner’s Manual HX350S SCAN MEM HX350S
Inhaltszusammenfassung zur Seite Nr. 7
i SCAN KEY Starts scanning programmed channels. Press this key for at least 1 second to turn on and off priority scan (scanning of programmed channels and priority channel) during scan. o MEM (Scrambler) KEY Memorizes the selected channel. When pressed again, deletes the memorized channel. Hold down this key for at least 1 second, to turn the scrambler on and off. (if an optional CVS240 voice scrambler is installed) !0 A/B KEY Immediately recalls two user assigned channels from any channel. !
Inhaltszusammenfassung zur Seite Nr. 8
3.2 INDICATORS DISTRESS CALLING USA TX CAN WX INTL MEM S HL Figure 2. Indicators Channel Display The operating channel in both transmission and reception mode. A Indicator Ship-ship channel in USA or Canadian mode whose counterpart in the International mode is a public corespondence (marine operator) channel. USA/INTL/CAN Indicator The modes of operation for the particular channel. “USA” indicates USA mode. “INTL” indicates International mode and “CAN” indicates Canadian mode. TX Indicator Indi
Inhaltszusammenfassung zur Seite Nr. 9
Battery Indicator Battery life, during transmission and reception, is as follows: : Over 50% charged : 25% charged : Less than 10% charged : Need to charge (Also see Section 5.1) NOTE The battey life indicator is accessed immediately by pressing the PTT switch. The battery indicator should be used only as a guide in charging the CNB350/CNB350AS battery. S Indicator S The small character “ ” above the keylock symbol “ ” on the display indicates the scrambler code. (only when CVS240 scrambler
Inhaltszusammenfassung zur Seite Nr. 10
4 OPERATION 4.1 INITIAL PROCEDURE NOTE Never key the transceiver without an antenna connected. Damage may occur to the transceiver. Do not operate the transceiver while charging. 1. Install the belt clip on the transceiver if desired. Use the 2 Phillips-head screws included with the clip to mount the clip to the back of the transceiver. 2. Install the nylon carrying strap on the belt clip if desired. 3. Install the battery pack on the transceiver. (see figure 4 and section 5.2) 4. Install t
Inhaltszusammenfassung zur Seite Nr. 11
6. To change channels, press the or key. Sometimes, a slight adjustment of the squelch threshold is needed as some channels have a higher noise level than others. Please refer to the Owner’s Manual Supplement for a complete listing of all USA, International and Canadian VHF Marine channels and their use. 7. If necessary, press the LAMP/ key to turn on the lamp. The lamp automatically turns off in about 5 seconds. To turn off the lamp sooner, press the LAMP/ key again. 8. To lock the channel i
Inhaltszusammenfassung zur Seite Nr. 12
4.4 TRANSMIT TIME - OUT TIMER (TOT) While the PTT switch is held down, transmission time is limited to 5 minutes. This prevents prolonged unintentional transmissions. About 10 seconds before automatic transmitter shutdown, a warning beep is sounded from the speaker. The transceiver automatically switches to the receiving mode, even if the PTT switch is held down. Before transmitting again, the PTT switch must first be released and pressed again. This time- out timer (TOT) prevents a continuou
Inhaltszusammenfassung zur Seite Nr. 13
4.7 SCAN 1. Select the desired channel to be scanned using the or key. 2. Press the MEM key to store the channel into the transceiver's memory. “MEM” is displayed on the LCD. 3. Repeat steps 1 and 2 for all the channels to be scanned. 4. To delete a channel from the transceiver’s scan memory, press the MEM key again while the memorized channel is displayed. “MEM” disappears. 5. All channels programmed remain in the transceiver’s scan memory even if the power is turned off. See section “4.17
Inhaltszusammenfassung zur Seite Nr. 14
4.9 WEATHER ALERT In the event of extreme weather disturbances such as storms and hurricanes, NOAA (National Oceanic and Atmospheric Administration) sends a weather alert accompanied by a 1050 Hz tone and subsequent weather reports on the weather channels. The transceiver is capable of receiving this alert if the following is performed: 1. Program weather channels into the transceiver’s memory for scanning. Follow the same procedure as for regular channels under Section 4.7. 2. Press the SCAN k
Inhaltszusammenfassung zur Seite Nr. 15
4.13 OPERATING ON CHANNEL 67 When channel 67 is used for navigational bridge-to-bridge traffic between ships, high power may be used temporarily in the USA mode by pressing the H/L key. When the H/L key is released, the transceiver will revert low power. 4.14 CHANNEL A/B INSTANT ACCESS Two user-assigned channels can be programmed for instant access. USA channels 9 and 16, and WX channels should not be assigned as A or B channels because they are readily available with the 16/9 and WX keys. If t
Inhaltszusammenfassung zur Seite Nr. 16
4.14.2 Operation Pressing the A/B key more than once toggles between channel A and channel B. Channel A is represented by “A” to the left of the channel number on the LCD, and channel B is represented by “b”. Do not confuse this “A” with the one that sometimes is displayed to the right of the channel number (described in the section 3.2 of this Owner’s Manual). 4.15 SIMPLEX/DUPLEX CHANNEL USE All channels are factory-programmed in accordance with FCC(USA), Industry Canada and International regul
Inhaltszusammenfassung zur Seite Nr. 17
3. Press the MEM key to store the scrambler code in the transceiver's memory. The display shows: USA TX CAN INTL S 4. Press the or key to set the scrambled channel (scrambled channel = CH05). The display shows: USA TX CAN INTL S 5. Press the MEM key to store the scrambled channel in the transceiver. “MEM” will be displayed on LCD. USA TX CAN INTL MEM S 6. To program other channels to be scrambled, repeat steps 4 and 5. Only one scrambler code can be chosen for all channels programmed. 4.16.2 O
Inhaltszusammenfassung zur Seite Nr. 18
4.17 RESETTING THE TRANSCEIVER’S MICROPROCESSOR Resetting the microprocessor restores the initial, factory supplied conditions in the transceiver. These are called the default conditions. To reset the microprocessor, first turn the transceiver off. Then while holding the WX and SCAN keys pressed, turn the transceiver on. The default conditions are: • No channel numbers are in memory. • Channel 16 is the priority channel. • Channel 16 will be selected when the transceiver is turned on. • WX ch
Inhaltszusammenfassung zur Seite Nr. 19
5 BATTERY CAUTION To avoid risk of explosion and injury, CNB350/CNB350AS battery pack should only be removed, charged or recharged in non-hazardous environments. 5.1 BATTERY CHARGING To check the charge status, install the battery and press the PTT switch while observing the BATT indicator. (see page 7) The battery charge system (CCA250 and CWC230) supplied with the transceiver recharges a completely discharged CNB350/CNB350AS battery pack in about 15 hours. Battery pack should not be charged w
Inhaltszusammenfassung zur Seite Nr. 20
5.3 OPERATING BATTERY CHARGE SYSTEM 1. Plug the end of CWC230 wall charger to the DC IN connector of the CCA250 charge adaptor. 2. Plug the wall charger into a 120 VAC wall outlet. 3. Turn the transceiver off. 4. Insert the transceiver. The indicator lights, and charging begins. 5. Remove the battery pack from charge adaptor when charging time has passed. NOTE The CWC230 can be replaced by the CAW240 mobile cable, or CWC232 120/230 VAC wall charger. CAUTION Never plug the power supply to the CCA
