Inhaltszusammenfassung zur Seite Nr. 1
Strata 128 Strata 128 Strata 128 Strata 128 Strata 128
Strata 128 Plus Strata 128 Plus
Strata 128 Plus Strata 128 Plus Strata 128 Plus
Strata 128 Por Strata 128 Portable table
Strata 128 Por Strata 128 Por Strata 128 Portable table table
StrataV StrataV StrataView iew iew
StrataV StrataView iew
INST INST INSTALLA ALLA ALLATION AND OPERA TION AND OPERA TION AND OPERATION TION TION
INST INSTALLA ALLATION AND OPERA TION AND OPERATION TION
INSTR INSTR INSTR INSTR INSTRUCTIONS UCTIONS UCTIONS UCTIONS
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION.............................................................................................. 3 SPECIFICATIONS ...........................................................................................3 INSTALLATION -Transducer ...........................................................................5 POWER CONNECTIONS .........................................................................
Inhaltszusammenfassung zur Seite Nr. 3
INTRODUCTION Thank you for purchasing an Eagle sonar. Your sonar unit is a high quality sonar designed for both professional and novice fishermen. All of our sonars have an automatic feature that finds and displays the bottom, fish, structure, and more! All you have to do is press the on key. However, if you wish to fine tune the unit, all you have to do is press the menu key. The Strata series has powerful features available through easy-to-use menus. To get started with your Eagle unit, f
Inhaltszusammenfassung zur Seite Nr. 4
Transducer Installation The transducer included with your sonar is a transom mount transducer The “kick-up” mounting bracket helps prevent damage if the transducer strikes an object while the boat is moving. If the transducer does “kick- up”, the bracket can easily be pushed back in place without tools. Read this manual carefully before attempting the installation. Determine which of the mounting positions is right for your boat. Use extreme care if mounting the transducer inside the hull, si
Inhaltszusammenfassung zur Seite Nr. 5
Shoot-thru-hull v.s. Transom Mounting (Strata 128 and Strata 128 Plus Only) Typically, shoot-thru-hull installations give excellent high speed opera- tion and good to excellent depth capability. There is no possibility of damage from floating objects. It can't be knocked off when docking or loading on the trailer. However, the shoot-thru-hull installation does have its drawbacks. One, some loss of sensitivity does occur, even on the best hulls. This varies from hull to hull, even from differ
Inhaltszusammenfassung zur Seite Nr. 6
2. Slide the transducer between the two ratchets. Temporally slide the bolt though the transducer assembly and hold it against the transom. Looking at the transducer from the side, check to see if it will adjust so that its face is parallel to the ground. If it does, then the “A” position is correct for your hull. If the transducer’s face isn’t parallel with the ground, remove the transducer and ratchets from the bracket. Place the ratch- ets into the holes in the bracket with the letter “B” ali
Inhaltszusammenfassung zur Seite Nr. 7
CAUTION! CAUTION! CAUTION! CAUTION! CAUTION! CLAMP THE TRANSDUCER CABLE TO CLAMP THE TRANSDUCER CABLE TO CLAMP THE TRANSDUCER CABLE TO CLAMP THE TRANSDUCER CABLE TO CLAMP THE TRANSDUCER CABLE TO TRANSOM NEAR THE TRANSDUCER. THIS TRANSOM NEAR THE TRANSDUCER. THIS TRANSOM NEAR THE TRANSDUCER. THIS TRANSOM NEAR THE TRANSDUCER. THIS TRANSOM NEAR THE TRANSDUCER. THIS WILL HELP PREVENT THE TRANSDUCER WILL HELP PREVENT THE TRANSDUCER WILL HELP PREVENT THE TRANSDUCER WILL HELP PREVENT THE TRANSDUCE
Inhaltszusammenfassung zur Seite Nr. 8
5. Remove the transducer from the bracket and re-assemble it with the cable passing through the bracket over the bolt as shown above. At- tach the transducer to the transom. Slide the transducer up or down until it’s aligned properly on the transom as shown above. Tighten the bracket’s mounting screws. Adjust the transducer so that it’s parallel to the ground and tighten the lock nut until it touches the flat washer, then add 1/4 turn. Don’t over tighten the lock nut! If you do, the transducer w
Inhaltszusammenfassung zur Seite Nr. 9
TROLLING MOTOR BRACKET INSTALLATION (StrataView Only) 1. Attach the TMB-S bracket to the transducer as shown below using the hardware supplied with the transducer. (Note: The internal tooth washer is supplied with the TMB-S.) TMB-S INTERNAL TOOTH BRACKET WASHER BOLT NUT FLAT WASHER 2. Slide the adjustable strap supplied with the TMB-S through the slot in the transducer bracket and wrap it around the trolling motor. Position the transducer to aim straight down when the motor is in the water. Tig
Inhaltszusammenfassung zur Seite Nr. 10
SHOOT-THRU-HULL (Strata 128 and Strata 128 Plus Only) The transducer installation inside a fiberglass hull must be in an area that does not have air bubbles in the resin or separated fiberglass layers. The sonar signal must pass through solid fiberglass. A success- ful transducer installation can be made on hulls with flotation materials (such as plywood, balsa wood, or foam) between layers of fiberglass if the material is removed from the chosen area. For example, some manufacturers use a la
Inhaltszusammenfassung zur Seite Nr. 11
TRANSDUCER LOCATION TRANSDUCER LOCATION (HIGH SPEED) (TROLLING SPEED) Shoot-thru-hull Installation (Strata 128 and Strata 128 Plus Only) 1. Make certain the area is clean, dry, and free of oil or grease, then sand both the inside surface of the hull and the face of the transducer with 100 grit sandpaper. The surface of the hull must be flat so the entire transducer face is in contact with the hull prior to bonding. SPREAD EPOXY HERE SAND THIS SURFACE 2. Follow the instructions on the epoxy p
Inhaltszusammenfassung zur Seite Nr. 12
hull. Place the transducer into the epoxy, twisting and turning it to force any air bubbles out from under the transducer face. The face of the transducer should be parallel with the hull, with a minimum amount of epoxy between the hull and transducer. After the epoxy dries, route the cable to the sonar unit. Fish Arches If you do not get good fish arches on your display, it could be the transducer is not parallel with the ground when the boat is at rest in the water, or at slow trolling spee
Inhaltszusammenfassung zur Seite Nr. 13
POWER CONNECTIONS - Permanent mount units only This unit works from a 12 volt DC system only. For the best results, run the power cable directly to the boat’s battery. Keep the power cable away from other boat wiring, especially the engine’s wires. This will give the best isolation from electrical noise. If the supplied cable is not long enough to reach the battery, splice #18 gauge insulated wire to it. You can attach the power cable to an accessory or power buss, however, you may have problems
Inhaltszusammenfassung zur Seite Nr. 14
Bracket Installation - Permanent mount units only You can install the sonar unit on the top of a dash or from an overhead with the supplied bracket. It can also be installed in the dash with an optional IDA-3 mounting kit. If you use the supplied bracket, you may be interested in the optional GBSA-1 swivel bracket kit. This converts the unit's gimbal bracket to a swivel mount which can be used on the dash or overhead mounting positions. Installation instructions for the in-dash and swivel mounti
Inhaltszusammenfassung zur Seite Nr. 15
STRATA 128 PORTABLE ASSEMBLY INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES Release the latch on the front of the battery case. Open the compartment and install four "D" cell batteries into the adapter. For the longest life, we recommend you use alkaline batteries. This battery case will also hold one rechargable battery instead of the "D" cells. See the enclosed coupon for more information on the rechargable battery
Inhaltszusammenfassung zur Seite Nr. 16
receive about portable units result from stale batteries. Make certain the ones you buy are fresh. Always remove batteries from the battery compartment before storing the unit as dead batteries can leak and corrode the contacts. In cold weather the efficiency of dry cell batteries drops with the tempera- ture. We find it a good idea to have the sonar unit good and warm along with the batteries before we leave home. If the batteries do lose a charge, you can sometimes restore them by placing t
Inhaltszusammenfassung zur Seite Nr. 17
Clean the chosen area of the hull before attaching the suction cup. Locate the transducer on the hull as shown below. Don't allow the bracket to go below the hull, as water pressure against it can cause the suction cup to come off at speed. Moisten the cup, then press it onto the hull as firmly as possible. Tie the nylon cord to the boat and route the transducer cable to the sonar unit. Plug the transducer connector into the unit and your portable sonar is now ready for use. HULL SPEED/TEM
Inhaltszusammenfassung zur Seite Nr. 18
Sensor Chart (Note: Do not use these sensors in any other combination.) ST-TBK = 1 speed sensor and 1 temperature display ST-T BK + TS-2BK = 2 temp sensors and one speed sensor ST-TBK + TS-2BK + TS-3BK = 3 temp sensors and one speed sensor TS-1BK = 1 temperature sensor TS-12BK = 2 temperature sensors or TS-1BK + TS-2BK = 2 temperature sensors TS-12BK + TS-3BK = 3 temperature sensors or TS-1BK + TS-2BK +TS-3BK = 3 temperature sensors Here's some sample wiring diagrams: TS-12 BK Two Temperature Se
Inhaltszusammenfassung zur Seite Nr. 19
TS-12 BK Sensor Chart (Note: Do not use these sensors in any other combina- tion.) TS-3 BK Three Temperature Sensors (Water, T-2, and T-3) STRATA PLUS OR STRATAVIEW POWER CABLE ST-TBK TS-2 BK TS-3 BK Three Temperature Sensors plus Speed (Water, T-2, T-3, and Speed) STRATA PLUS OR STRATAVIEW POWER CABLE 19
Inhaltszusammenfassung zur Seite Nr. 20
KEYBOARD BASICS The unit sounds a tone when you press any key. This tells you the unit has ac- cepted a command. PWR/CLEAR Use this key to turn the unit on. It also clears menu selections and the menus from the screen. This key also turns the unit off. NOTE: You must hold the OFF key down for a few seconds in order to turn the unit OFF. MENU FWD / MENU REV These sonar units have many features that are accessed with the menu keys. The MENU FWD key moves forward through the menus, the MENU REV k
