Bedienungsanleitung Metra Electronics 99-9401

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-9401
APPLICATIONS
2004-2006 Land Rover Freelander
99-9401
KIT FEATURES
• DIN Head Unit Provision With Removable Pocket
KIT COMPONENTS
A) Radio Housing B) Pocket
B
A
TOOLS REQUIRED:
Socket Wrench • Phillips Screwdriver • Small Flat Blade Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION

Inhaltszusammenfassung zur Seite Nr. 2

99-9401 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Inhaltszusammenfassung zur Seite Nr. 3

P R N D 4 2 1 P R N D 4 2 1 DASH DISASSEMBLY 99-9401 2004-2006 LAND ROVER FREELANDER A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Put gear shifter into neutral position then remove shift knob. (Figure A) 3 Unclip and remove gear shifter trim panel. (Figure B) 4 Unclip and remove rear ashtray B panel from back of center console. (Figure C) Open center console lid and remove 5 cubby box. (Figure D) D C 1

Inhaltszusammenfassung zur Seite Nr. 4

DASH DISASSEMBLY 99-9401 2004-2006 LAND ROVER FREELANDER E 6 Remove the (2) screws securing the rear of the center console. (Figure E) 7 Remove the screw cover in front of the window switches then remove the (2) screws exposed underneath. (Figure F) 8 Unclip and remove the upper console finisher panel between the a/c vents and radio.. (Figure G) F Remove the (4) screws securing the 9 center console. (Figure H) Remove the (2) screws securing the radio. H G 2

Inhaltszusammenfassung zur Seite Nr. 5

KIT ASSEMBLY 99-9401 2004-2006 LAND ROVER FREELANDER DIN HEAD UNIT PROVISION A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket head unit into the DIN cage until secure. (Figure B) Slide the included pocket into the 3 Radio Housing until secure. (Figure C) B 4 Install kit assembly into dash. C 3

Inhaltszusammenfassung zur Seite Nr. 6

FINAL ASSEMBLY 99-9401 FINAL ASSEMBLY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassem

Inhaltszusammenfassung zur Seite Nr. 7

99-9401 NOTES 5

Inhaltszusammenfassung zur Seite Nr. 8

99-9401 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 06/19/07 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-9401