Inhaltszusammenfassung zur Seite Nr. 1
DVR4/9-SecuraNet™
USER MANUAL
SW242-4SN / SW242-9SN / SW243-4MB / SW243-9MB
Inhaltszusammenfassung zur Seite Nr. 2
Getting Started FCC WARNING STATEMENT This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation Important Notice All jurisdictions have specific laws and regulations regarding the use of cameras. Before using any camera for any purpose, it is the buyer’s responsibili
Inhaltszusammenfassung zur Seite Nr. 3
Contents Chapter 1: DVR Features ........................................................................................................................ 1 Chapter 2: DVR Layout ........................................................................................................................... 2 2.1 Front Panel........................................................................................................................................ 2 2.2 Rear Panel........................
Inhaltszusammenfassung zur Seite Nr. 4
8.1 Playback Control ............................................................................................................................. 24 Chapter 9: USB Programming(optional)............................................................................................ 25 9.1 Client Program Installation............................................................................................................... 25 9.2 Program Interface................................................
Inhaltszusammenfassung zur Seite Nr. 5
1. DVR Features 4-Channel: 4 BNC Camera Inputs - 2 BNC Video Outputs 9-Channel: 9 BNC Camera Inputs - 1 BNC Video Output 4-Channel: 2 Audio Inputs - 2 Audio Outputs 9-Channel: 1 Audio input - 1 Audio Output View and Operate over Network (Broadband Connection Required) NTSC or PAL System Motion Detection with Sensitivity and Area Settings Timed Schedule, Alarm and Motion Triggered Recording Modes Hard Disk Support up to 500GB Built-in USB 2.0 Port for Backup to Computer
Inhaltszusammenfassung zur Seite Nr. 6
2. DVR Layout 2.1 Front Panel (All Models) 1. Power switch 10. Record 23. IR Receiver 2. Removable HDD Tray 11. CH1 24. Up Arrow 3. HDD Lock 12. CH2 25. Select 4. USB 2.0 Interface 13. CH3 26. Left Arrow 5. Rewind 14. CH4 27. Down Arrow 6. Pause 15-19. CH5-9 (9CH DVR Only) 28. Right Arrow 29. Power Indicator 7. Play 20. Mute Audio 30. HDD Indicator 8. Fast Forward 21. Display All Cameras 9. Stop 22. Menu / Exit Menu 2
Inhaltszusammenfassung zur Seite Nr. 7
2.2 Rear Panel 1. Audio Input(s) 7. VGA Output (Optional) 13. CH6 2. Video Output(s) 8. LAN 14. CH5 3. CH4 9. Audio output 15. RS485 / Sensor Input / 4. CH3 10. CH9 Alarm Output 5. CH2 11. CH8 16. DC Power Input Jack 6. CH1 12. CH7 17. Grounding Terminal 3
Inhaltszusammenfassung zur Seite Nr. 8
2.3 Remote Control 1-9 Channel Select 1-9 0 Number ALL Display All Channels Menu Enter or Exit Menu ▲ Move Up / Left ▼ Move Down / Right SEL Select / Modify Item Rewind Play Recording Fast Forward Record / Pause ● / Stop Recording / Playback ■ Audio Audio Input / Output 4
Inhaltszusammenfassung zur Seite Nr. 9
3. Hard Drive Installation WARNING: Do not remove Hard Drive while DVR is running Ensure HDD jumpers are set to MASTER prior to inserting drive SW243-4MB / SW243-9MB has a hard drive pre-installed, please skip this step. 3.1 Installing a Fixed SATA Hard Disk 1 - Unlock and remove hard drive drawer from left side of the DVR 2 - Remove hard drive from drawer (if applicable) 3 - Align and connect power and SATA connectors to hard drive drawer
Inhaltszusammenfassung zur Seite Nr. 10
4. DVR Connections 6
Inhaltszusammenfassung zur Seite Nr. 11
5. Starting the DVR 5.1 Firmware Version After connecting the power adapter and turn on the power button, the system will boot-up and display the version and released date of the DVR’s current firmware. 5.2 Detecting Installed Hard Drive DVR will detect the installed hard drive and display the hard drive information. 5.3 Format Hard Drive When the DVR detects a new hard drive you will be prompted to format the hard drive before u
Inhaltszusammenfassung zur Seite Nr. 12
6. DVR Menu System 6.1 Navigating the Menus [MENU]: enters Main Menu [ ▲, ▼, ◄ and ►]: move the cursor [SEL]: select/modify settings [MENU]: press again to exit or return to previous menu. 6.2 Menu Overview Camera Setup Record Setup Record Frame rate Change Password Video Quality Set Time Record Schedule Hidden Channel Sensor Setup Audio Port Setup Main Menu Hard Drive Setup PTZ Setup Miscellaneous Setup Auto Record Auto Sequence Network Setup Keypad
Inhaltszusammenfassung zur Seite Nr. 13
6.3 Camera Setup Camera Setup allows you to turn cameras on or off. Press ▲, ▼, ◄ or ► button to select a channel and then press [SEL] to modify the setting ON or OFF. Note: If a camera channel is set to off it will not record (Refer to 6.4 Record Setup) 6.4 Record Setup Record Setup allows you to set up recording channels. Press ▲, ▼, ◄ or ► button to select a channel, and then press [SEL] to modify the setting to ON or OFF. If a channel is disa
Inhaltszusammenfassung zur Seite Nr. 14
6.6 Video Quality Video Quality has 4 different settings: Highest, High, Normal and Low. The higher the video setting the better quality images, however higher quality images require more hard drive space. Press [SEL] to change the quality setting. 6.7 Record Schedule Setting the Record Schedule allows you to customize the type of recording depending on the time of day. The time line indicates 24 hours of a day based on AM/PM (0 = 12). Press ▲, ▼, ◄ o
Inhaltszusammenfassung zur Seite Nr. 15
6.8 Sensor Setup Sensor Record Time indicates how long the recording time is when the motion or sensor is triggered. Alarm On Time indicates whether the buzzer will sound when motion is detected. CONT: Continuous alarm until any key is pressed. OFF: No alarm 6.9 H/W Sensor Setup Note: Sensors and extension alarms are not included with the DVR system and may be purchased separately. HARDWARE SENSOR SETUP: There are 3 different modes for sensor set
Inhaltszusammenfassung zur Seite Nr. 16
Area Selection: Press ▲, ▼, ◄ or ► button to select a block, and press [SEL] button to set the block to detect motion, The area is detectable when it is clear, the area is not detectable when it is covert by shadow. 6.11 Hard Drive Setup This section will display the current hard drive status and usage options OVERWRITE ENABLED: ON: overwrite oldest video when hard drive is full. OFF: stop recording when hard drive is full. HDD SIZE: indica
Inhaltszusammenfassung zur Seite Nr. 17
Enter the current password first, and then enter six characters as your new password, repeat the new password to confirm. If you forget your password, please contact technical support for assistance. 6.13 Miscellaneous Setup - Set Time The system date and time format is YYYY/MM/DD and HH:MM: SS. Press ◄ or ► button to select the data to modify, press [SEL] to modify. Press [MENU] to save and return to previous menu. 6.14 Miscellaneous S
Inhaltszusammenfassung zur Seite Nr. 18
6.15 Miscellaneous Setup - Audio Port Setup For 4-channel DVR, there are 2 audio inputs. For 9-channel DVR, there is 1 audio input. You can select the audio recording function to ON or OFF, and select the video channel that you like to record the audio on. 6.16 Miscellaneous Setup - PTZ Setup SPEED: Set the baud rate (4800 9600 19200 38400) match to your speed dome. PROTOCOL: Supports “PELCO-D” and “PELCO-P”. Select the protocol according to your
Inhaltszusammenfassung zur Seite Nr. 19
6.18 Miscellaneous Setup - Auto Sequence Auto sequence function allows you to view each active video channel in full screen mode and display alternately. Auto Sequence dwelling time can be also adjusted to 1, 2, 5, 10, 15, 30 or 60 seconds, or turn it off by choosing OFF. To activate Auto Sequence mode, press [ ] button during monitoring or recording mode. To exit auto sequence display, press [MENU] or any of channel selection buttons. 6.19 Miscellaneous Setu
Inhaltszusammenfassung zur Seite Nr. 20
CON: Contrast BRI: Brightness HUE: Hue SAT: Saturation Press ▲ or ▼ to select the item, and then press [SEL] to adjust the value. 6.21 Miscellaneous Setup - Password Enable The password will be required to control the DVR when this option is set to “ON”, and the password is not required when this option is set to “OFF”. 6.22 Miscellaneous Setup - VGA Setup Select a VGA resolution match to your CRT or LCD monitor. NOTE: VGA video output i
