Bedienungsanleitung Metra Electronics 99-3303

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-3303
APPLICATIONS
Chevrolet Cobalt 2005-2006
Chevrolet Malibu 2004-2007
Chevrolet Malibu Classic 2008
Pontiac G6 2005-2009
99-3303
KIT FEATURES
• DIN Head Unit Provision with
Driver Information Center (DIC)
• ISO DIN Head Unit Provision with
Driver Information Center (DIC)
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) DIN Spacer • E) Wire Harness
D
E
C
A
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiri

Inhaltszusammenfassung zur Seite Nr. 2

99-3303 • Dash Disassembly - Chevrolet Malibu 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 - Chevrolet Malibu Classic 2008. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 - Pontiac G6 2005-2009 .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Chevrolet Cobalt 2005-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 • Kit Assembly - DIN Head Unit Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 5

Inhaltszusammenfassung zur Seite Nr. 3

DASH DISASSEMBLY 99-3303 CHEVROLET MALIBU 2004-2007 CHEVROLET MALIBU CLASSIC 2008 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. 2 Unclip and remove wood grain/painted trim pieces from both sides of steering wheel. (Figure A) 3 Unclip and remove side panel from driver’s B side of dash with door open and remove (2) 7MM screws. (Figure B) 4 Remove (2) 7MM screws from bottom edge of panel below steering wheel. Unclip panel and let hang. It is not necessary to

Inhaltszusammenfassung zur Seite Nr. 4

99-3303 CHEVROLET MALIBU 2004-2007 CHEVROLET MALIBU CLASSIC 2008 E 6 Unclip and remove side panel from passenger side of dash with door open and remove (2) 7 MM screws from behind panel. (Figure E) 7 Remove (2) 7 MM screws from bottom of glove box then open box and squeeze sides together to open further and remove F the remaining (4) 7MM screws. Unclip the black vent cover under the glove box then unclip and remove entire glove box assembly. (Figure F) 8 Unclip and remove trim panel surroundin

Inhaltszusammenfassung zur Seite Nr. 5

DASH DISASSEMBLY 99-3303 PONTIAC G6 2005-2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open glove box and remove (6) screws from outer edge then unclip and remove box. (Figure A) 3 Remove (4) screws from panel below steer- ing column and unclip and remove panel. B (Figure B) 4 Unclip and remove center panel surrounding radio and A/C controls. (Figure C) 5 Remove (4) screws and extract radio from sub dash. (Figure D) C D 3

Inhaltszusammenfassung zur Seite Nr. 6

99-3303 CHEVROLET COBALT 2005-2006 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove trim panel from above glove box. (Figure A) 3 Unclip upper edge of panel below steering B column and let hang. Not necessary to remove completely. (Figure B) 4 Unclip and remove small trim panel to right of ignition switch. (Figure C) 5 Unclip and remove trim panel surrounding radio and climate controls. (Figure D) C 6 Remove (4) 9/32 screws securing radio.

Inhaltszusammenfassung zur Seite Nr. 7

KIT ASSEMBLY 99-3303 DIN HEAD UNIT PROVISIONS: A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket head unit into the cage and secure. (Figure B) NOTE: A snap-in DIN spacer has been provided for some applications where depth is an issue. Snap the spacer in the B housing and slide the DIN cage into the assembly and secure by bending the metal locking tabs outward. (Figure C) C 5

Inhaltszusammenfassung zur Seite Nr. 8

99-3303 ISO DIN HEAD UNIT PROVISIONS: A 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) Slide the head unit into the radio opening 2 until the side clips engage. (Figure B) 3 Snap the Trim plate into the Radio Housing. (Figure B) B 6 KIT ASSEMBLY

Inhaltszusammenfassung zur Seite Nr. 9

FINAL ASSEMBLY 99-3303 FINAL ASSEMBLY 1 Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. All connections should be made without the harness plugged into the 99-3303. A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D METRA / EIA

Inhaltszusammenfassung zur Seite Nr. 10

FINAL ASSEMBLY 99-3303 OPERATION OF THE 99-3303 Settings and Adjustments mode There is a Settings and Adjustments mode available for the individualized adjustment of the contrast of the display, brightness of the display and backlighting, OnStar volume, and the button backlighting color. Entering the Settings and Adjustments mode To enter the Settings and Adjustments mode, press the INFO and MENU buttons simultaneously. When the unit settings and adjustments mode is entered, the LCD will disp

Inhaltszusammenfassung zur Seite Nr. 11

NOTES 99-3303 9

Inhaltszusammenfassung zur Seite Nr. 12

INST993303 1-800-221-0932 www.metraonline.com Rev. 05-27-09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-3303