Bedienungsanleitung Metra Electronics 99-1008

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-1008
APPLICATIONS
• 2003-2006 Kia Sorento LX
• 2004.5-2006 Kia Spectra
99-1008
KIT FEATURES
• Recessed DIN Head Unit
• ISO Head Unit Provisions with Pocket
KIT COMPONENTS
A) Radio Housing I B) ISO Brackets I C) Trim Plate
A
C
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver I Phillips Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION

Inhaltszusammenfassung zur Seite Nr. 2

99-1008 • Dash Disassembly - 2003-2006 Kia Sorento LX ...................................................... 1 - 2004.5-2006 Kia Spectra ........................................................ 2 • Kit Assembly - DIN Head Unit Provision........................................................... 3 - ISO DIN Head Unit Provision...................................................... 3 • Final Assembly ...........................................................................4 • Notes.............

Inhaltszusammenfassung zur Seite Nr. 3

DASH DISASSEMBLY 99-1008 2003-2006 KIA SORENTO LX A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open ash tray and unsnap and remove outside trim panels. (Figure A) Tip: Start at the bottom of the trim B panels. 3 Remove (8) Phillips screw from the radio trim panel. Disconnect any plugs from the trim panel and then remove panel. (Figure B) C 4 Remove (4) Phillips screw from radio to remove radio. (Figure C) 5 Cut along the scored lines of the radio housi

Inhaltszusammenfassung zur Seite Nr. 4

99-1008 2004.5- 2006 KIA SPECTRA A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Using a flat blade screwdriver as a 2 pry tool, unsnap and remove the center dash panel including the cli- mate controls and vents from around the radio. (Figure A) B Remove (4) phillips screws to 3 remove radio. (Figure B) 2 DASH DISASSEMBLY

Inhaltszusammenfassung zur Seite Nr. 5

KIT ASSEMBLY 99-1008 DIN HEAD UNIT PROVISION A Slide the DIN cage into the Radio 1 Housing and secure by bending the metal locking tabs down. (Figure A) Slide the aftermarket head unit into 2 the cage and secure. Snap the Trim plate into the Radio Housing. 3 ISO DIN HEAD UNIT PROVISION A Mount the ISO Brackets to the head 1 unit with the screws supplied with the unit. Slide the head unit into the radio 2 opening until the side clips engage. (Figure A) Snap the Trim plate into the Radio 3 Housing

Inhaltszusammenfassung zur Seite Nr. 6

99-1008 A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the 1 dash. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble in reverse order of disassembly. 4 FINAL ASSEMBLY

Inhaltszusammenfassung zur Seite Nr. 7

NOTES 99-1008 5

Inhaltszusammenfassung zur Seite Nr. 8

INST991008 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION Rev. 06-13-07