Inhaltszusammenfassung zur Seite Nr. 1
Thank you for buying a Samsung SYSTEM CONTROLLER.
This manual will guide you through using the SYSTEM CONTROLLER. Please read this manual carefully
before using the SYSTEM CONTROLLER.
Inhaltszusammenfassung zur Seite Nr. 2
Contents (5-1) TOUR Setup 19 ●Important Safety Instructions 3 (5-2) TOUR Operation 19 ●Major Functions and Features (6) MODEL 21 (1) Overview 5 (7) TRACE 22 (2) Features 5 (7-1) TRACE Memory 22 ●Product Components 5 (7-2) TRACE Operation 23 ●System Overview 6 (8) AF 23 ●Names and Functions of Each Part (9) OSD 24 (1) Camera Setup Section 7 ●DVR Mode 25 (2) Number Pad 8 ●Controller Mode (3) External Device Selectors 8 (1) Controller Setup Mode 26 (4) Universal Controller 9 (2) Controller ID Setu
Inhaltszusammenfassung zur Seite Nr. 3
Important Safety Instructions Warning ■ All work related to the installation of this appliance must be performed by qualified service personnel or system installers. - If the product is connected or installed improperly, electric shock, fire, severe injury, and/or damage can result. ■ Please install the product on a completely flat floor. - Always check the strength and stability of the installation location. - Do not drop the appliance on the floor. This may result in damage or injury. ■ Do not
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Instructions Maintenance and Repair ■ If the controller body gets dirty, turn the power off and wipe the surface with a soft cloth. - Do not use chemical agents such as alcohol or benzene. ■ For detailed information on upgrading the firmware, please direct your inquiries to the installation vendor. Refer all work related to the installation of this appliance to qualified service personnel or system installers. This equipment has been tested and found to comply with the limits fo
Inhaltszusammenfassung zur Seite Nr. 5
Major Functions and Features (1) Overview This product is designed for use only with the Speed Dome camera, CCTV receiver, and Samsung Digital Video Recorder. ● Speed Dome camera : Samsung Techwin (SPD-1600/2200/2500), PELCO-D, PANASONIC (WV-CS854A), SAMSUNG ELECTRONICS (SCC-643-641) ● CCTV Receiver : SRX-100B ● DVR : Samsung Techwin (SVR-1630/1620/430) (2) Features - It is possible to totally control the 255 Speed Dome camera, CCTV Receiver and Samsung Digital Video Recorder. - If the Speed Dom
Inhaltszusammenfassung zur Seite Nr. 6
Inhaltszusammenfassung zur Seite Nr. 7
Names and Functions of Each Part (1) Camera Setup Section ① RESET : Resets camera power. ② PRESET : Moves camera to the preset location (see p.16). ③ LIGHT : Toggles the lights around the camera on and off. ④ AUX : Toggles the camera’s external case AUX on and off. ⑤ TOUR : Sets more than 1 group for tour and performs continuous group action (see p.19). ⑥ SALVO : Not used; will be applied to F/W in the future. ⑦ SWING : Continuously travels between two assigned locations horizontally (pan) or
Inhaltszusammenfassung zur Seite Nr. 8
Names and Functions of Each Part (2) Number Pad ※ 'F' in the table below refers to the Function button. ① 0 ~ 9 : Used for entering camera ID, channel number, monitor number, DVR ID, etc. (see p.23). ② F + 0 : Activates the system setup menu (see p.24). ③▲ / ▼ : Used for increasing or decreasing menu values in detailed setup menus. ※ When using functions that are performed by a combination of the function button and numeric keys, the setup may be different depending on the camera manufacturer.
Inhaltszusammenfassung zur Seite Nr. 9
Names and Functions of Each Part (4) Universal Controller ① ZOOM W/T : Performs camera zoom action (wide and telephoto). ② FOCUS -/+ : Used for manual focus adjustment. ③ || : Used for moving the menu cursor up (when menu is active), pausing DVR playback, or playing stills. ④■ : Used for moving the menu cursor down (when menu is active) or stopping DVR playback. ⑤I▶ : Used for moving the menu cursor left (when menu is active) or Slow Playback. ⑥▶▶ : Used for moving the menu cursor right (when m
Inhaltszusammenfassung zur Seite Nr. 10
Names and Functions of Each Part ※ Some DVR controller buttons may not be supported or may be used differently than as described in this manual, depending on the DVR model. Please refer to the table below for the buttons supported by major DVR model manufacturers. The DVR button with multiple functions works in the same way on the controller. SVR-430 SVR-900 SVR-1620 SVR-1630 QUICK SET O - - - STATUS O O O - SEARCH O O O O PLAY MODE - O O - FOCUS - O O O O FOCUS + O O O - O O O II O Jog(PLAY MO
Inhaltszusammenfassung zur Seite Nr. 11
Names and Functions of Each Part (6) Camera Controller ① Joystick: Used for moving the camera up, down, left, and right, and for zoom control (see p.13). 1) Tilt up (Up button): Moves the camera up. 2) Tilt down (Down button): Moves the camera down. 3) Tilt left (Left button): Moves the camera left. 4) Tilt right (Right button): Moves the camera right. 5) Turn stick clockwise: Performs telephoto-zoom. 6) Turn stick counter-clockwise: Performs wide zoom. ② SLOW : Sets the camera movement (up, dow
Inhaltszusammenfassung zur Seite Nr. 12
Before Operation (1) Power-On ① Power on the connected external devices before turning the controller on. ② Press the power button at the back of the controller to power on the controller. ③ The [SYSTEM Controller] message and F/W version will be displayed in the LCD monitor, and the message will disappear when the controller is ready for use. ▤ The [JOYSTICK ERROR] error will be displayed in the LCD monitor if the joystick is not placed in the center during power-on. [ power button ] (2) Initia
Inhaltszusammenfassung zur Seite Nr. 13
Before Operation (4) Joystick/Camera Control Button ■ The joystick can be used to control the camera ’ s left and right (pan) and up and down (tilt) movements. ■ The joystick can be used to control camera zoom functions. [Camera wide zoom] [Camera telephoto zoom] 《13 》
Inhaltszusammenfassung zur Seite Nr. 14
Before Operation (5) Camera Movement Speed Control ■ Use the joystick or press the Slow/Fast button at the bottom of the camera control button section to adjust the camera movement speed. ▤ You must press the ESC button after adjusting the camera movement speed in order to be able to use other controller buttons. [SLOW/FAST button] ▤ The SLOW/FAST button can be used to adjust movement speed for models without a joystick. (6) Camera Zoom Control ■ Press the ZOOM W/T button to control zoom wide an
Inhaltszusammenfassung zur Seite Nr. 15
PTZ Mode (1) PTZ Setup Mode ■ This menu is for setting up the PTZ camera function. It is impossible to operate Speed Dome and DVR by sub-controllers when the master controller is set to on. ① At the initial screen, press the Function button and press the 0 button SETUPSYSTEM to activate the [SETUP SYSTEM] menu. 1:PTZ 2:DVR 3:CONTROLLER PressNumericKey ② Press the 1 button to activate the [PTZ SETUP 1 ▶] menu. PTZSETUP1 1:PRESET 2:SWING 3:GROUP 4:TOUR PressNumericKey ③ Press the ▶▶ button to act
Inhaltszusammenfassung zur Seite Nr. 16
PTZ Mode (2) PRESET ■ This menu is for setting the camera to move to preset locations. (2-1) PRESET Setup ① At the [PTZ SETUP 1 ▶] menu, press the 1 button (see p.15). PTZSETUP1 5SPD CAMID: ② Use the joystick or camera control button (SCC-3000 model) to move PRESETNO:0 the camera to the desired location (move up, down, left, and right, and Enter:PresetIDSet control zoom). ③ Enter a preset number. PTZSETUP1 CAMID:5SPD PRESETNO:1 Enter:PresetIDSet ④ Press the Enter button to assign the number to t
Inhaltszusammenfassung zur Seite Nr. 17
PTZ Mode (3) SWING ■ This menu is for setting the camera to alternate between two assigned locations horizontally (pan) or vertically (tilt). Setting the SWING SETUP menu by controllers is only possible in the SPD series. In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more information. (3-1) SWING Setup ① At the [PTZ SETUP 1 ▶] menu, press the 2 button (see p.15). SWINGSETUP SWINGSETUP CAMID: CAMID: 5SPD 5SPD ② Pre
Inhaltszusammenfassung zur Seite Nr. 18
PTZ Mode (4) GROUP ■ This menu is for setting repeated sequential surveillance of assigned locations with assigned speed and intervals. Setting the GROUP SETUP menu by controllers is only available for an SPD series. In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more information. (4-1) GROUP Setup ① At the [PTZ SETUP 1 ▶] menu, press the 3 button (see p.15). GROUPSETUP CAMID: 5SPD ② Enter a Group number. GROUPSETN
Inhaltszusammenfassung zur Seite Nr. 19
PTZ Mode (5) TOUR ■ This menu is for setting one or more Groups for Tour so that continuous Group operations can be carried out. The TOUR SETUP menu is only available for an SPD series. (5-1) TOUR Setup ① At the [PTZ SETUP 1 ▶] menu, press the 4 button (see p.15). TOURSETUP 1GROUPNUM?<1-6> ② Press a Group number to add to the Tour. Enter:TourSet ▤ Up to 6 Groups can be added. ③ Press the ENTER button to finish the setup. (5-2) TOUR Operation ① At the initial screen, press the Tour button. ② The
Inhaltszusammenfassung zur Seite Nr. 20
