Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Safety Precautions The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insulated dangerous Voltage within the product’s enclosure that may be sufficient magnitude to constitute risk of electrical shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature
Inhaltszusammenfassung zur Seite Nr. 3
Before reading this document 1. This document is intended for both the administrator and users of this stand alone DVR Model. 2.This manual contains information for configuring, managing and using this stand alone DVR Model. 3. To prevent fire or electrical shock, do not expose the product to heat or moisture. 4. Be sure to read this manual before using this stand alone DVR Model. 5. For questions and technical assistance of this product, contact Q-see. ►Strong recommendation o
Inhaltszusammenfassung zur Seite Nr. 4
CONTENTS 1. FEATURES AND FUNCTION…………………………………………………………………….…..5 2. UNIT DESCRIPTION OF FRONT PANEL.…………………………………………………..……….6 3. REAR PANEL AND SYSTEM CONNECTION…..……………………………………………………8 4. REMOTE CONTROL…………………………………………………………………………………12 5. SYSTEM SETUP………………….………………………………………………..………………..12 5.1. SETUP MENU.………………..…………………………………………………………………12 5.2. SYSTEM SETUP…………………………………………………………………………………14 5.2.1. TIME/DATE SET……………………………………………………………………………...14 5.2.2. HDD FORMAT SET…………………………………………
Inhaltszusammenfassung zur Seite Nr. 5
1. FEATURE AND FUNCTION l Video input: 16channels; Video output: 3channels. l Audio input: 4channels; Audio output: 2channels. l 16 alarm input and 1 relay alarm output. l Compression mode: M-JEPG. l Support network view. l Support USB backup. l Compatible with NTSC and PAL format. l Support zoom, auto function, watermark security. l Four optional levels of image quality: very high, high, low, very low. Record and play-back frame rate are changeable. l Support alarm recording, time re
Inhaltszusammenfassung zur Seite Nr. 6
2. UNIT DESCRIPTION OF FRONT PANEL 2.1 Recording/Playing Control Buttons Area 1. REC: It is manual recording button. Press this button to record video to hard disk, Re-press this button, it will stop recording. So, this button is the switch button of manual recording and stopping recording operation, recording and stop will work simultaneously on 16 channels. This button doesn’t work in schedule mode. 2. PLAY: Press this button to start playing the video stored in hard disk, re-press
Inhaltszusammenfassung zur Seite Nr. 7
1. Auto/1: Auto key, in shift mode, press this button, The DVR will be in auto dwell state, it dwells according to the time set in auto sequence set menu, and you can set the dwell time of each channel. Press this button to quit this mode. If not in shift mode, press this button to see big picture of channel 1. While inputting numbers, this button is used as number key of “1”. 2. Zoom/2: Zoom key, in shift mode, press this button, the DVR will be in zoom mode, please refer to zoom operation
Inhaltszusammenfassung zur Seite Nr. 8
11. SF/0: Single frame forward button, in shift mode, while in playback state, long press this button can see single frame forward, press play button to play normally. If not in shift mode, press this button to see big picture of channel 10.while inputting numbers, this button is used as number key of”0”. 12. Search/Menu: press this button to enter search menu, please refer search play in user guideline for details. Long press this key to enter menu (need password), in menu setup, press
Inhaltszusammenfassung zur Seite Nr. 9
3.1 Back panel and connection terminals The power cable and input, output signal terminals are all at the back of the machine, the connection to monitor, camera etc equipments are all carried out through the terminals and sockets on the back panel the back view of the machine is illustrated as below. Each part of the back panel is illustrated as below: 1. Video input CH1-CH16 2.main output 3.assistant monitor 4.S-VIDEO 5.audio input 6.audio output 7.net interface 8.USB port 9.power 10.debu
Inhaltszusammenfassung zur Seite Nr. 10
2. Open/Close output A: N.O. Normal open, close when triggered. DVR must set as low voltage alarm. B: N.C. Normal close, open when triggered. DVR must set as high voltage alarm. Please refer to the picture below, channel 2 to channel 16 are the same as channel 1. Alarm output: There are three alarm output pin, the status of these pin are illustrated as below Before Alarm After Alarm There is an example for alarm output conne
Inhaltszusammenfassung zur Seite Nr. 11
3.4 Hard Disk Connection There are processing to install the hard disk. Note: If the DVR comes with a HDD pre-installed then skip the following steps. 1. Pull out the hard drive rack from DVR 2. Connect the DATA cable & power cord. side panel. 4. Close the top cover of the drawer and 3. Open the top cover of the drawer. put the hard drive drawer back into the DVR 5. Lock the hard drive draw by turning the key clockwise.
Inhaltszusammenfassung zur Seite Nr. 12
4. REMOTE CONTROLLER 0 – 9, 10+: Select the channel (Full screen) 2x2: 2x2 Screen Modes 3x3: 3x3 Screen Modes 4x4: 4x4 Screen Modes USB: USB Storage Backup AUTO: Auto Sequence Mode ZOOM: 2X Zoom FREEZE: Freeze DISPLAY: Hard Disk Information MENU/EXIT: System Setup SEARCH: Time Search, Event Search and Start Stop Search ENTER: Enter Next Menu REC: Record WM: Watermark set PTZ: Control Speed dome 5. SYSTEM SETUP Before using the video recorder, the first step is to set u
Inhaltszusammenfassung zur Seite Nr. 13
If you enter the correct password, the main menu will display ad below. 13
Inhaltszusammenfassung zur Seite Nr. 14
5.2 SYSTEM SETUP Press “ENTER” button to enter sub menu PLAY REPEAT: Set the Playback Repeat VIDEO SYSTEM: Set the NTSC/PAL BUZZER SOUND: Set the Buzzer On/Off 5.2.1 TIME/DATA SET Set the date and time. DATE: Set the date TIME: Set the time FORMAT: Set the time display format (USA, EURO and Asia Users) DISPLAY: Set the time display on/off LOCAL: Set the time display position 14
Inhaltszusammenfassung zur Seite Nr. 15
5.2.2 HDD FORMAT SET Format the hard disk. Select “YES”, to format the hard disk. And all video on the HDD will loss. 5.2.3 FACTORY RESET Initialize all the setup; the DVR will reset to factory default settings. 15
Inhaltszusammenfassung zur Seite Nr. 16
5.2.4 Change Password When the cursor moves to CHANGE PASSWORD, please press the enter button, and the Change Password window will appear. Password Level: password type of the DVR, the DVR has various types of password: SETUP: If set to “YES”, you have to input password to enter menu. SYSTEM: If set to “YES”, you have to input password to boot the DVR. ALWAYS: If set to “YES”, you have to input password to all operation. If you select the Password Change and press the Enter button,
Inhaltszusammenfassung zur Seite Nr. 17
5.2.5 Firmware Update When the cursor moves to FIRMWARE UPDATE, please press enter button, and the firmware update window will appear. Update Method: There are two methods to update the DVR firmware, USB (for USB thumb drives) and Network (not support) USB update: create a new folder named “firmware” in the USB thumb drive’s root directory, copy the update file to the folder, and plug in the USB thumb drive. Enter the Firmware Update menu, select Update Start and press enter button, th
Inhaltszusammenfassung zur Seite Nr. 18
5.3 DISPLAY SETUP BOUND COLOR: Set the Color of Video Boundary (BLACK / WHITE / GRAY). BLANK COLOR: Set the Background Color of Loss Video (BLACK / WHITE). 5.3.1 CAMERA NAME SET When the cursor moves to Camera Name, please press the Enter button, the Camera Name Setup window will appear. Press the up or down button to select channels, press the Enter button to change the channel name. 18
Inhaltszusammenfassung zur Seite Nr. 19
Each channel’s name is a combination of six eight characters. Press up or down button to select each character, press LEFT or RIGHT button to modify each character, and then press enter button to save this name. DISPLAY: if Display is set to “OFF”, the channel’s name will not display on the screen. 5.3.2 COLOR SET When the cursor moves to Color Set, please press the Enter button, the Color Setup window will appear. CON: picture contrast BRI: picture brightness HUE: picture h
Inhaltszusammenfassung zur Seite Nr. 20
5.3.3. AUTO SEQUENCE SET When the cursor moves to Autoseq Set, please press enter button, the Auto Sequence Setup window will appear. Press the UP or DOWN button to select channel, press LEFT or RIGHT button to change the auto Sequence time. 5.4 RECORD SETUP When the cursor moves to Record Set, then press the Enter button, the Record Setup window will appear, which is illustrated as below. Press UP or DOWN button to move the cursor. Then press the LEFT or RIGHT button to change the
