Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION INSTRUCTIONS FOR PART 95-7313
APPLICATIONS
2001-2006 Hyundai Elantra
2003-2008 Hyundai Tiburon
2002-2005 Hyundai Sonata
2001-2006 Kia Optima (2006 Early Production Models Only)
95-7313
KIT FEATURES
• DDIN Head Unit Provision
• STACKED ISO DIN Head Unit Provision
KIT COMPONENTS
A) DDIN Trim Plate | B) DDIN Brackets
B
A
TOOLS REQUIRED:
Flat Blade Screwdriver I Phillips Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION
Inhaltszusammenfassung zur Seite Nr. 2
95-7313 Dash Disassembly ........................................................................ 1-4 Kit Assembly ................................................................................. 5-6 Final Assembly ................................................................................. 7 TABLE OF CONTENTS
Inhaltszusammenfassung zur Seite Nr. 3
DASH DISASSEMBLY 95-7313 2001-2006 HYUNDAI ELANTRA 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) Phillips screws from under the instrument cluster. Remove ashtray then remove (2) 3 Phillips screws in ashtray cavity. 4 Unclip and remove panel surround- ing radio. (Figure A) 5 Remove (4) Phillips screws securing radio. A 1
Inhaltszusammenfassung zur Seite Nr. 4
95-7313 2003-2008 HYUNDAI TIBURON Disconnect the negative battery terminal to 1 prevent an accidental short circuit. 2 Unclip and remove the radio trim panel starting with the bottom edge. (Figure A) Remove (2) Phillips screws securing radio. 3 A 2 DASH DISASSEMBLY
Inhaltszusammenfassung zur Seite Nr. 5
DASH DISASSEMBLY 95-7313 2002-2005 HYUNDAI SONATA 2001-2005 KIA OPTIMA 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove entire panel sur- B rounding radio. (Figure A) Remove (4) Phillips screws securing 3 radio. The rear support bar in the sub dash 4 will need to be cut and removed for aftermarket radio clearance. (Figure B) A 3
Inhaltszusammenfassung zur Seite Nr. 6
95-7313 2006 KIA OPTIMA(2006 Early Production Models Only) A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. Unclip and remove panel surround- 2 3:30 ing shifter. (Figure A) Remove (2) Phillips screws at bottom 3 of panel surrounding radio and cli- mate control then unclip and remove entire panel. (Figure B,C) B Remove (4) Phillips screws securing 4 radio. (Figure D) The rear support bar in the sub dash 5 will need to be cut and removed for aftermarket radio
Inhaltszusammenfassung zur Seite Nr. 7
KIT ASSEMBLY 95-7313 DOUBLE DIN HEAD UNIT PROVISION A Slide the appropriate bracket into 1 the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) Slide the DDIN radio unit into the 2 trim plate bracket assembly and secure the unit to the kit using the screws supplied with the head unit. B (Figure B) C NOTE: For the 2003-2008 Hyundai Tiburon applications you will need to cut and remove the bottom mount- ing tabs on the DDIN brackets. CUT (Figure C) CUT 5
Inhaltszusammenfassung zur Seite Nr. 8
95-7313 STACKED ISO DIN HEAD UNIT PROVISION A 1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 2 Slide the stacked ISO DIN units into the trim plate bracket assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure B) B C NOTE: For the 2003-2008 Hyundai Tiburon applications you will need to cut and remove the bottom mounting tabs on the DDIN brackets. (Figure C) CUT CUT 6 KIT ASSEM
Inhaltszusammenfassung zur Seite Nr. 9
FINAL ASSEMBLY 95-7313 FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring
Inhaltszusammenfassung zur Seite Nr. 10
95-7313 NOTES 8
Inhaltszusammenfassung zur Seite Nr. 11
95-7313 NOTES 9
Inhaltszusammenfassung zur Seite Nr. 12
95-7313 INSTRUCTIONS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION INST95-7313 REV. 05/20/08
