Bedienungsanleitung Metra Electronics 95-3304

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 95-3304
APPLICATIONS
See application list inside
GM multi-kit 2005-up
95-3304
KIT FEATURES
• Double DIN radio provision
• Stacked ISO DIN head unit provision
KIT COMPONENTS
• A) Trim Plate • B) Brackets
A B
WIRING & ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• GMOS-01 GM Onstar and chime harness 2002-up
• GMOS-04 GM Onstar and chime and amp harness 2002-up
Antenna Adapter:
• 40-GM10 GM antenna adpter 1988-up
TOOLS REQUIRED
Socket Wrench • Phill

Inhaltszusammenfassung zur Seite Nr. 2

95-3304 Applications Buick Hummer Saturn Terraza 2005-2008 H3 2006-2010 Relay 2005-2007 Chevrolet Pontiac Corvette 2005-up Montana (SV6 only) 2005-2007 Uplander 2005-2008 Table of Contents Dash Disassembly – Buick Terraza 2005-2008 3 – Chevrolet Uplander 2005-2008 3 – Pontiac Montana SV6 2005-2007 3 – Saturn Relay 2005-2007 3 – Chevrolet Corvette 2005-up 4 – Hummer H3 2006-2010 5 Kit Assembly – DDIN head unit provision 6 – Stacked ISO DIN head unit provision

Inhaltszusammenfassung zur Seite Nr. 3

Dash Disassembly 95-3304 Buick Terraza 2005-2008 Chevrolet Uplander 2005-2008 Pontiac Montana SV6 2005-2007 Saturn Relay 2005-2007 1. Unclip and remove trim panel around radio and a/c control. (Figure A) 2. Remove (8) 9/32” screws to extract radio and a/c control from sub dash. (Figure A) Continue to kit assembly (Figure A) 3

Inhaltszusammenfassung zur Seite Nr. 4

Dash Disassembly 95-3304 Chevrolet Corvette 2005-up 1. Unclip and remove ride control switch/ 3. Unclip and remove entire panel blank plate at front edge of center surrounding radio and including console lid. (Figure A) a/c controls. (Figure A) 2. Remove (2) 9/32” screws from under 4. Remove (4) 9/32” screws securing radio plate removed in step 2. (Figure A) to extract from sub dash. (Figure A) Continue to kit assembly (Figure A) 4

Inhaltszusammenfassung zur Seite Nr. 5

Dash Disassembly 95-3304 Hummer H3 2006-2010 1. Unclip and remove trim panel around radio and a/c controls. (Figure A) 2. Remove (4) 9/32” screws securing radio. (Figure B) 3. Unplug and remove radio. Continue to kit assembly (Figure A) (Figure B) 5

Inhaltszusammenfassung zur Seite Nr. 6

Kit Assembly 95-7951 Double DIN radio provision 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 3. Slide the DDIN radio unit into the trim (Figure A) plate bracket assembly and secure the unit to the

Inhaltszusammenfassung zur Seite Nr. 7

Kit Assembly 95-7951 Stacked ISO DIN head unit provision 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 3. Slide the stacked ISO DIN units into the (Figure A) trim plate bracket assembly and secure

Inhaltszusammenfassung zur Seite Nr. 8

INSTALLATION INSTRUCTIONS FOR PART 95-3304 METRA. THE WORLD’S BEST KITS.™ metraonline.com 1-800-221-0932 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION REV. 5/25/11