Inhaltszusammenfassung zur Seite Nr. 1
VER1.3
8Channel Stand-alone DVMR
Inhaltszusammenfassung zur Seite Nr. 2
Installation & Safeguards INSTALLATION & SAFEGUARDS All the safety and operating instructions should be read before the unit is operated. Environment Condition for Installation - To prevent electric shock or other hazard, do not expose units to rain, moisture, or dust. - This unit should be located in an area with low humidity and a minimum of dust.. - Place this unit in a well-ventilated place and do not place heat-generating objects on this unit. - This unit should not be located in an area w
Inhaltszusammenfassung zur Seite Nr. 3
Contents Contents CHAP. 1 Features & Package Contents ---------------------------------------------------------------- 4 1-1. Features ---------------------------------------------------------------- 4 1-2. Package Contents ---------------------------------------------------------------- 5 CHAP. 2 Function of Each Button ---------------------------------------------------------------- 6 2-1. Front ---------------------------------------------------------------- 6 2-2. Rear ----------------------
Inhaltszusammenfassung zur Seite Nr. 4
Contents 4-8. PTZ Camera Operation ---------------------------------------------------------------- 19 4-9. Data Back-Up ---------------------------------------------------------------- 19 CHAP. 5 Set Up ---------------------------------------------------------------- 20 5-1. Entering the Menu ---------------------------------------------------------------- 20 5-2. Display Setup ---------------------------------------------------------------- 21 1) Screen Display --------------------------------
Inhaltszusammenfassung zur Seite Nr. 5
CHAP. 1 Features & Package Contents CHAP. 1 Features & Package Contents 1-1. Features Live View Real time display per camera Auto Sequence PIP (Picture in picture) Digital Zoom Display Freeze Simple Playback mode Simple PTZ camera control Record Variable Record resolution (For higher picture quality or higher recording speed) Efficient Image Quality setup in 5 steps Schedule Record / Holiday Record Event Record (Alarm / Motion) Emergency Record Network View Live and Playback images across IP
Inhaltszusammenfassung zur Seite Nr. 6
CHAP. 1 Features & Package Contents 1-2. Package Contents 1. DVR Main Unit 2. Remote Controller 3. Power Cable 6. Software CD 4. Power Adapter 5. User’s Manual 7. Rubber Pad 8. HDD absorber 9. Battery for remote controller 10. Bolts Package Contents Description 1. DVR Main Unit STAND-ALONE DIGITAL VIDEO RECORDER 2. Remote Controller DVR control 3. Power Cable AC power supply to adapters for 12 V DC power 4. Power Adapter 12 V DC power supply 5. User’s Manual User’s Manual 6. Software CD Remot
Inhaltszusammenfassung zur Seite Nr. 7
CHAP. 2 Function of Each Button CHAP. 2 Function of Each Button 2-1 FRONT Name Function ① LED Lamps Shows status of operation ② USB Device Firmware upgrade by connecting PC with latest firmware to USB port ③ IR IR receiver ④ Camera 1. Pressing this button will display a full screen image of that camera selection 2. Control PTZ camera (Each button is assigned for each PTZ command) & • ON : LIGHT ON • SET : SET PRESET PTZ camera control • OFF : LIGHT OFF • CLEAR : CLEAR PRESET • OPEN : IRIS OP
Inhaltszusammenfassung zur Seite Nr. 8
CHAP. 2 Function of Each Button Name Function ⑦ LIVE View PTZ On/Off for PAN/TILT/ZOOM control mode Control Press this button first to control PTZ camera connected to DVR unit via RS-485 ZOOM Zooming an image FRZ Freezing an image MODE Switch to split display MODE button changes screen-division from (to) full screen to (from) 8 split screen. PIP Display in PIP (Picture in Picture) mode SEQ Auto camera image sequencing in full screen mode K.LOCK Lock the key function. To unlock, press longer t
Inhaltszusammenfassung zur Seite Nr. 9
CHAP. 2 Function of Each Button 2-2. REAR Name Function 1 RS 485 Connection with PTZ Camera or other external device using RS 485 interface RELAY Output Relay out terminal SENSOR Input Sensor input terminal 2 VGA Connection to VGA Monitor (CRT type or TFT LCD monitor) Just in case you purchased DVR with VGA option board fixed on the main board of DVR, you can connect VGA Monitor to DVR unit. 3 ETHERNET Connection to ETHERNET device 4 RS-232C Connection to external device as PC using RS-232C
Inhaltszusammenfassung zur Seite Nr. 10
CHAP. 3 Installation CHAP.3 Installation 3-1. Installation Configuration 9
Inhaltszusammenfassung zur Seite Nr. 11
CHAP. 3 Installation 3-2. Detailed Installation 1) Rack mount 1. Remove 4 bolts on each side cap to install rack mount. 2. Attach rack mount bracket to DVR. 3. Attach DVR with rack mount bracket to 19” rack. 2) HDD 1. Connect Main Board and HDD1 using IDE cable and HDD power cable. 2. The jumper setting of HDD1 should be on Master if you install only one HDD. 3. The jumper setting of HDD1 should be on Master and HDD2 should be on Slave if you install two HDDs.(Refer to the above
Inhaltszusammenfassung zur Seite Nr. 12
CHAP. 3 Installation 3) Camera Connect cameras to the camera input on rear panel of DVR marked CAMERA IN. 4) Monitor Connect the video output marked MONITOR to Video-In of Main monitor. 5) Power Connect one DC 12V, 8.3 A Adaptor to the back side of Power Jack for right operation of 2HDDs and CDRW. Before you turn on the Power switch, be sure all necessary devices such as Power adaptor, cameras and Monitor are connected properly to DVR! Notice To avoid accidental deletion of HDD data, please
Inhaltszusammenfassung zur Seite Nr. 13
CHAP. 3 Installation 6) VCR, VIDEO PRINTER Connect VCR or VIDEO Printer to VCR out on the rear panel of DVR. 7) Other External Device RS-232C : Control DVR through RS-232C port by using PC. RS-485 : Control external device like PTZ Camera RELAY Output : Relay Output SENSOR Input : SENSOR Input (Alarm connection) ETHERNET : Connection to LAN, WAN, Internet. VGA : Connection to a VGA monitor(CRT,TFT LCD) if optional VGA board is fixed on the main board as shown in the following figure. Resoluti
Inhaltszusammenfassung zur Seite Nr. 14
CHAP. 3 Installation 8) Connector Pin Assignment No Description NO Description 1 DCD Data Carrier Detect 6 DSR Data Set Ready 2 RxD Receive data 7 RTS RS232C: Rx/Tx data 3 TxD Transmit data 8 CTS RS232C: Rx/Tx data 4 DTR Data Terminal data 9 5 GND Signal Ground 9) RS-232C ASCII-code Following ASCII-Codes(Hexa-Code) are for programmers who want to control DVR unit via the RS232C Port using keyboard of PC. (The following table is based on 16ch DVR.) All ASCII-Code is 1 Byte. REC ‘R’ DOWN
Inhaltszusammenfassung zur Seite Nr. 15
CHAP. 4 Operation 4-1. System Log-In DVR LOG-IN 1) To enter into the setup menu, press the [MENU] button. 2) Enter password with channel number button from No.1 to No.10 on the front of the DVR unit. ENTER PASSWORD : _ _ _ _ _ _ _ _ (Maximum of 8 digits are available) INPUT YOUR OWN PASSWORD 3) After inputting the password, press the [ENTER] button. TO EXIT, PRESS [MENU] Administrator : If the password entered matches previously set password, “ LOGIN ADMIN” message appears and you can ente
Inhaltszusammenfassung zur Seite Nr. 16
CHAP 4. Operation 4-3. Display Configuration HDD Status ETHERNET status In live mode : Amount of data recorded Connected In Playback mode : Amount of data played Disconnected 1. Current Time & Date 3. Status of DVR system Emergency Record (Red) Schedule Record (Green) Record Stop (White) Stop PIP Forward Playback Backward Playback FREEZE Pause 1/16~1/2x forward playback SEQUENCE 1/16~1/2x backward playback 2~4x forward playback ZOOM 2~4x backward playback 16~64x forward playback 16~64x
Inhaltszusammenfassung zur Seite Nr. 17
CHAP. 4 Operation 2) View in Sequence Press [SEQ] button. It automatically displays full screen images in sequence. CH08 …… ● CH02 ● CH01 ● 3) Picture in Picture(PIP View) When it is in full screen display mode, you can see other camera in a small window by pressing [PIP].The other camera in small window is rotating in sequence to next number of camera and you can set the rotating time interval as per the procedure in SYSTEM MENU-CONFIGURATION- INTERVAL SETUP. CAM-01 2 4) Freeze View Full d
Inhaltszusammenfassung zur Seite Nr. 18
CHAP. 4 Operation 4-5. Record Recording mode set before delivery by manufacturer (Default recording mode) is Schedule Recording. In this default recording mode, it records 24 hours/day continuously in weekday and on the weekend. Once you press the [REC] button while you see live view, the record type is changed to Emergency Record mode. - Emergency Record : at full resolution/in best quality Emergency Record [RED] Record type : CONTINUOUS, SUPER FINE quality, 120 (100) ips at 720X240 (720x288)
Inhaltszusammenfassung zur Seite Nr. 19
CHAP. 4 Operation If you want to keep the playback speed you selected using Shuttle, just hold the shuttle at that location for a few seconds, and playback in speed you selected continues until you rotate Shuttle again. 4-7. Search Press [SEARCH] button, and 3 different methods for searching recorded data are available as shown in following SEARCH window. For selecting searching method, use direction key or Jog/Shuttle. After selecting each search method, press [ENTER] button for playback. e
Inhaltszusammenfassung zur Seite Nr. 20
CHAP. 4 Operation 4-8. PAN/TILT/ZOOM Camera Operation Press [PTZ] button first for PTZ control mode. Numeric buttons from 1 to 16 and direction buttons are assigned for each PTZ command, and user can control PTZ camera connected to DVR unit by pressing any one of those 20 buttons, one after the other, as needed, and it is just like control by separate PTZ controller. Button PTZ command Button PTZ command 1/ON LIGHT ON 10/CLEAR PRESET CLEAR 2/OFF LIGHT OFF 11/GOTO PRESET GOTO 3/OPEN IRIS OPE
