Inhaltszusammenfassung zur Seite Nr. 1
4 CH Digital Video Recorder
User’s Manual
Please read this instructions thoroughly before operation and keep the manual in a safe
place for further reference.
773W V1.0
Inhaltszusammenfassung zur Seite Nr. 2
WARNING All the safety and operating instructions should be read before operation. Improper operations may cause permanent damage. • This adaptor is only for this machine. Do not use it for other electronic products or it will damage other products. • Please lift and place this equipment gently. • Do not expose this equipment to direct sunlight. • Do not use this equipment near water or in contact with water. • Do not spill liquid of any kind on the equipment. • Please power down the unit bef
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS What do you get ? • FEATURES --------------------------------------------------------------------------------------- 1 1 • PACKAGE CONTENT ------------------------------------------------------------------------- Before Operation • INSTALLATION GUIDE ------------------------------------------------------------------------ 2 • FRONT PANEL ------------------------------------------------------------------------------------ 3 • REAR PANEL ------------------------------------------
Inhaltszusammenfassung zur Seite Nr. 4
Inhaltszusammenfassung zur Seite Nr. 5
Before Operation INSTALLATION GUIDE 1. Connect cameras and monitor to the DVR. 2. Shown below is an example of connecting the DVR to your existing Observation System. 3. Install HDD (The compatible HDD brands are listed in the following table.) Please refer to page.45 Appendix #1 for installation instructions. Note: The HDD must be installed before turning on the DVR. If HDD is not installed, the DVR would function as a 4 CH multiplexer. COMPATIBLE HARD DISK MODELS Manufacturer Model Capacity Ro
Inhaltszusammenfassung zur Seite Nr. 6
FRONT PANEL 1 2 1. REMOVABLE HDD CARTRIDGE Please refer to page.44 Appendix #2. & KEYHOLE 2. CONTROL PANEL LED LIGHT The LED Light is ON under the following conditions. •HDD : HDD is reading or recording. •HDD Full : HDD is full •ALARM : To turn off the ALARM LED light, please refer to page.12 and set the ALARM mode as OFF. •TIMER : When Timer is Enabled •PLAY : Playing mode •REC : Recording mode MENU Press MENU button to enter main menu. Press ENTER button for confirmation. ENTER SEARCH
Inhaltszusammenfassung zur Seite Nr. 7
FF / ► •FF: Play video fast forward. (Press FF button again to adjust speed as 1, 2, 4, 8, 16, 32 times) •► : Under setup mode, it works as Right button. •REW : Play video fast backward. (Press REW button again to adjust REW / ◄ speed as 1, 2, 4, 8, 16, 32 times) •◄ : Under setup mode, it works as Left button. STOP / ▼ •STOP : Under DVR Recording / Playing mode, it can stop the action. •▼ : Under setup mode, it works as Down button. PAUSE / ▲ •Pause : Under DVR playing mode, it can make the
Inhaltszusammenfassung zur Seite Nr. 8
REAR PANEL 1. LAN Connect DVR by LAN cable. 2. EXTERNAL I/O •Controlled remotely by an external device or control system such as Video Web Server or PC. •Alarm input, external I / O expansion. 3. VIDEO INPUT (1-4) Connect to video source, such as camera. 4. CALL Connect to CALL monitor. Show the Switch Display. When the alarm is triggered, the call monitor will show the triggered channel for a period of time. 5. MAIN Connect to Main monitor. 6. AUDIO IN (1-4) Connect to audio sources, such as
Inhaltszusammenfassung zur Seite Nr. 9
Basic Operation GETTING STARTED Before using the DVR, please have a HDD installed ready, or it will function as 4 CH multiplexer (refer to Appendix #1 and Appendix #2 for installation or removal of a HDD). 1. Connect the AC power cord and plug into an electrical outlet. The Red LED indicator light will be ON and the DVR is in standby mode. 2. Press the Power button. The POWER LED will turn from red to orange, and other red LED indicators will turn ON. It takes approximately 5 to 15 seconds to
Inhaltszusammenfassung zur Seite Nr. 10
PLAY BACK Press “PLAY ” button, the DVR will show the last recording. 1. FAST FORWARD (F.F.) & FAST REWIND (F.R.) You can increase the speed of Fast Forward and Rewind on the DVR. In the Play mode, press “► ” once to get 2X speed forward and press twice to get 4X speed,… and the maximum speed can reach 32X. Press “◄ ” once to get 1X speed rewind and press twice to get 2X speed, … and the maximum speed can reach 32X. 2. SLOW FORWARD (S.F.) & SLOW REWIND (S.R.) You can also slow down the speed
Inhaltszusammenfassung zur Seite Nr. 11
Detailed Menu Setup MAIN MENU There are 12 options available in the Main Menu: (MENU) TIMER TIMER ---------- Program Timer Recording CAMERA CAMERA ------- Camera Setup RECORD RECORD ------- Recording Mode Setup ALARM ALARM --------- Alarm Setup DWELL DWELL --------- Dwell time Setup PIP PIP --------------- Picture in Picture Setup MOTION MOTION -------- Motion Detection Setup DISPLAY DISPLAY ------- Display Mode Setup NETWORK NETWORK -----Network Setup USER USER ----------- User Password Set
Inhaltszusammenfassung zur Seite Nr. 12
8. MESSAGE LATCH To select whether the DVR messages will disappear after 10 (SYSTEM) seconds or remain on screen. NO is the default setting which the AUDIO INPUT 1 messages will disappear after 10 sec. BUZZER ON NOTE : Video loss, Alarm and Motion messages will be shown EXT ALARM ON like the Alarm Duration time. VLOSS ALARM ON MOTION ALARM ON
Inhaltszusammenfassung zur Seite Nr. 13
2. START (TIMER) DAY START END IPS QLT MODE Set the time to start the recording. DAILY 01:00 22:00 30 BEST Q-FR OFF 00:00 00:00 30 BEST Q-FI OFF 00:00 00:00 30 BEST Q-FI 3. END OFF 00:00 00:00 30 BEST Q-FR Set the time to end the recording. OFF 00:00 00:00 30 BEST Q-FR OFF 00:00 00:00 30 BEST Q-FR OFF 00:00 00:00 30 BEST MUX 4. IPS (IMAGE PER SECOND) OFF 00:00
Inhaltszusammenfassung zur Seite Nr. 14
3. REC (RECORD) Set up which channel you want to record. ON : when alarm input is triggered, DVR will record alarming channel more frequently. For example : when CH01 is triggered, the record method will become 1-2-1-3-1-4…. OFF : DVR will not record. 4. BR (BRIGHTNESS) Adjust the brightness of each channel. The level is from 0 to 63. 5. CT (CONTRAST) Adjust the contrast of each channel. The level is from 0 to 63. 6. CL (COLOR) Adjust the color of each channel. The level is from 0 to 63. 7.
Inhaltszusammenfassung zur Seite Nr. 15
ALARM 1. ALARM ENABLE Alarm will be triggered by event occurrence when the setting is YES. 2. ALARM DURATION Set the reaction time which was determined by how long the alarm mode responded to a buzzer. Default setting is 10 sec. Options are 10 Sec, 15 Sec, 20 Sec, 30 Sec, 1 MIN, 2 MIN, 3 MIN, 5 MIN, 10 MIN, 15 MIN, 30 MIN, ALWAYS, AUTO. NOTE : 1. Video loss, Alarm and Motion messages is shown like the Alarm Duration time is. 2. When the setting is AUTO, the alarm duration time is based on the
Inhaltszusammenfassung zur Seite Nr. 16
MOTION (MOTION) SEN MD-NUM RE DET CAM1 70 03 64 ON AREA CAM2 70 03 64 OFF AREA CAM3 70 03 64 ON AREA CAM4 70 03 64 ON AREA MOTION RECORD : ON DAY START END DAILY 00 : 00 00 : 00 1. SEN (SENSITIVITY) Sets the sensitivity of the pixel-based Motion Detection feature from 1 to 99. The highest sensitivity setting is 01, the lowest sensitivity setti
Inhaltszusammenfassung zur Seite Nr. 17
Figure 1-1 Figure 1-2 MOTION DETECTION SETUP MOTION DETECTION SETTING — ROW SETUP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 11 11 12 12 Figure 1-3 Figure 1-4 MOTION DETECTION TRIGGERED-TURN INTO PURPLE BACK TO MOTION DETECTION SETTING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 11 11 12 12 6. MOTION RECORD When the DET setting is “ON”, you can set up
Inhaltszusammenfassung zur Seite Nr. 18
7. DAY / START / END To setup the DAY and the START/ END time for motion trigger recording timer setting. DISPLAY (DISPLAY) TITLE DISPLAY YES 1. TITLE DISPLAY OSD COLOR YELLOW To set the title shown on monitor or not. LOSS SCREEN GREEN TIME POSITION NORMAL 2. OSD COLOR Select the OSD (On Screen Display) color. The options are YELLOW, GREEN, CYAN, BLUE, PINK, GRAY, WHITE, RED. 3. LOSS SCREEN Retain the last picture or select the LOSS SCR
Inhaltszusammenfassung zur Seite Nr. 19
USER 1. USER (USER) To set up the user account for controlling. It allows 8 users setting. PASSWORD Supervisor – Control all the functions. SUPERVISOR 0000 Other Users – View all functions except the USER 1 0000 menu setting and event list USER 2 0000 cleaning. USER 3 0000 USER 4 0000 USER 5 0000 2. PASSWORD USER 6 0000 To set the security password for each account. USER 7 0000 The maximum length of user’s password is 4
Inhaltszusammenfassung zur Seite Nr. 20
Hardware CONNECTION Network Setting Guide AT SERVER SITE 17
