Inhaltszusammenfassung zur Seite Nr. 1
JPEG2000 Stand alone DVR User Guide
CONTENTS
Date: 2006/07/05 VER: 1.5
Caution …………………………………………………………………….3
Package …………………………………………………………………….3
Specification …………………………………………………………………….4
CHAP.1 Appearance
1-1 Front panel introduction ……………………………………………………………………. 6
1-2 Back panel introduction ……………………………………………………………………. 8
1-3 IR remote controller introduction ……………………………………………………………………. 9
CHAP.2 Installation
2-1 Camera and monitor installation ……………………………………………………………………. 10
Inhaltszusammenfassung zur Seite Nr. 2
JPEG2000 Stand alone DVR User Guide CHAP.5 CD-R bck-up 5-1 Data backup …………………………………………………………………… 44 5-2 CD-R player software installation …………………………………………………………………… 45 5-3 CD-R player software interface …………………………………………………………………… 46 CHAP.6 PTZ camera control 6-1 PTZ camera installation …………………………………………………………………… 48 6-2 PTZ camera operation …………………………………………………………………… 49 CHAP.7 Network & remote software 7-1 Network configuration …………………………………………………………………… 50 7-2 Network install
Inhaltszusammenfassung zur Seite Nr. 3
JPEG2000 Stand alone DVR User Guide Caution For you safety, unplug the power before moving the DVR, installing, or replacing any parts or hard drive. Make sure all the power cable and wires are properly set up before using the DVR. Contact your distributor immediately if there is any defect. To avoid a short circuit, don’t leave any unnecessary parts inside the DVR. Please avoid dramatic changes of the environment, such as dust, temperature, and humidity. Keep the DVR in a tempe
Inhaltszusammenfassung zur Seite Nr. 4
JPEG2000 Stand alone DVR User Guide Specification Model 4/8/16 CH JPEG2000 Stand Alone DVR 4/8/16CH VIDEO IN 1.0 VP-P，75OHM(BNC TYPE) Video Input Video I/O Video Output (BNC TYPE) X 2 VGA Output Support TFT LCD Monitor (Optional) Audio Input 4 CH Audio Input (MONO type) Audio I/O (Optional) Audio Output 1 CH Audio output (MONO type) FULL: 720(H) × 480(V) (NTSC) 720(H) × 576(V) (PAL) Display Resolution 1/4: 360(H) × 240(V) (NTSC) 360(H) × 288(V) (PAL) Monitorin
Inhaltszusammenfassung zur Seite Nr. 5
JPEG2000 Stand alone DVR User Guide Protocol TCP/IP Network Remote Softeware: Remote live view, playback, and save as AVI Remote monitoring IE: Remote live view, backup, and save backup to AVI Back-up VCR, CD-R back-up, Backup via IE PTZ Control RS485，supports PELCO D and other protocols RS232 Controls DVR host through RS232 4CH: 4 Alarm Inputs Alarm Input 8CH: 8 Alarm Inputs Assistant 16CH: 16 Alarm Inputs Functions Alarm Output 1(Programmable alarm output duration) Remote Con
Inhaltszusammenfassung zur Seite Nr. 6
JPEG2000 Stand alone DVR User Guide CHAP.1 Appearance 1-1 Front panel introduction 1.[CD-RW] Built-in CD-RW for CD-R back-up. 2.[IR Receiver & LED Lamps] IR Remote Controller Receiver. DVR Status LED: RUN- Flashes when play picture by picture through J. Shuttle. ACTIVE- On when the J. Shuttle is ready to use. REC- On while recording and flashes at stand-by mode, such as no motion triggered at the motion record mode PLAY- On while playback.
Inhaltszusammenfassung zur Seite Nr. 7
JPEG2000 Stand alone DVR User Guide 10.[Control] SEQ- Full screen sequencing or the smaller screen sequencing in PIP mode. PIP- For entering the Picture in Picture mode from full screen mode. NEXT- Switch other control keys in PTZ mode. Switch to other channel in a split screen. ZOOM- To enlarge the picture. Use the direction buttons and move to the area to be enlarged. 11.[REC] To activate Emergency Record at continuous, Super fine quality and Best resolution. Press STOP to
Inhaltszusammenfassung zur Seite Nr. 8
JPEG2000 Stand alone DVR User Guide 1-2 Back panel introduction [4Channel] [8Channel] [16Channel] 1.[RS485, Relay Output, Sensor Input] RS485, for direct connection to PTZ cameras. 16 sensor inputs and 1 relay output. 2.[VGA Output] Connection to a VGA monitor or TFT LCD. 3.[ETHERNET] Connection to Ethernet device. 4.[RS-232C] Connection to PC or other DVR control devices. 5.[1~16 Camera Input/LOOP Output] CAMERA IN- channel 1~1
Inhaltszusammenfassung zur Seite Nr. 9
JPEG2000 Stand alone DVR User Guide 1-3 IR remote controller introduction 1.[MENU] Enter menu or exit 2.[Split /OSD] 4S: 4 split 9S: 9 split 16S: 16 split OSD: OSD words on/off 3.[1~16 Channel] Switch channel in live or playback; password entering 4.[Control function] FRZ- Freeze the screen in display SEQ- Automatically display full screen or split screen in sequence ZOOM- To enlarge the picture. Use the direction buttons and move to the area to be enlarged
Inhaltszusammenfassung zur Seite Nr. 10
JPEG2000 Stand alone DVR User Guide CHAP.2 Installation 2-1 Camera and monitor installation 2-1-1 Camera installation Connect camera to DVR camera in CH1~CH16 ※Please do not start the DVR before the camera. installation is done. 2-1-2 Monitor and VCR installation
Inhaltszusammenfassung zur Seite Nr. 11
JPEG2000 Stand alone DVR User Guide 2-1-3 Loop out installation To monitor a single channel, connect the “loop out” of the corresponding channel to a monitor.
Inhaltszusammenfassung zur Seite Nr. 12
JPEG2000 Stand alone DVR User Guide 2-2-3 Relay output installation Alarm output can be NO or NC, depending on the settings. NO-COM: the NO and COM terminals are open-circuit, and it’ll become closed-circuit when alarm triggered. NC-COM: the NC and COM terminals are closed-circuit, and it’ll become open-circuit when alarm triggered. 2-3 Network and serial port installation 2-3-1 Network setup Connect the network cable to “Ethernet”on back panel. Ethern
Inhaltszusammenfassung zur Seite Nr. 13
JPEG2000 Stand alone DVR User Guide ASCII-CODE connector description 1 DCD Func. CODE Func. CODE Func. CODE Func. CODE Func. CODE 2 RxD REC R RIGHT K MODE D CH3 3 CH11 ! 3 TxD STOP S NEXT N PIP I CH4 4 CH12 @ 4 DTR PLAY P ENTER 0X0D SEQ Q CH5 5 CH13 # 5 GND SEARCH E - < J.SHU L CH6 6 CH14 $ 6 DSR MENU M + > KLOCK C CH7 7 CH15 % 7 RTS UP U PTZ T QPLAY Y CH8 8 CH16 ^ 8 CTS DOWN J ZOOM Z CH1 1 CH9 9 9 NC LEFT H FRZ F CH2 2 CH10 0 To connect DVR to a PC, users must
Inhaltszusammenfassung zur Seite Nr. 14
JPEG2000 Stand alone DVR User Guide 2-4 HDD installation [Steps] 1. Disassemble the bolts as illustrated. 2.Jumper setting Set up the HDD as MASTER or SLAVE. Please refer to the HDD manual of the jumper settings. 3.HDD Installation Please insert the HDD as shown in , and make sure the HDD is set as “MASTER”. Caution: 1. Power off the DVR before HDD installation. 2. Jumper s
Inhaltszusammenfassung zur Seite Nr. 15
JPEG2000 Stand alone DVR User Guide 2-5 Power plugging Insert the adapter to the rear power socket of DVR. Insert the power cable to the other side of adapter. Plug in the power cable and power on the DVR. Caution: Please use a 100~240VAC 50~60HZ and 12VDC 8A or 5A power supply or it may damage the DVR. - 15
Inhaltszusammenfassung zur Seite Nr. 16
JPEG2000 Stand alone DVR User Guide CHAP.3 Operation 3-1 Display configuration 1.[Time] Current system time or the recorded time in playback 2.[Date] Current system date or the recorded date in playback 3.[Camera title] Camera title of the displayed channel. Camera title can be modified in [SYSTEM MENU] [CONFIGURATION] [CAMERA SETUP] [CAMERA TITLE]. . 4.[Record mode] The current recording mode alarm motion continuous 5.[Record
Inhaltszusammenfassung zur Seite Nr. 17
JPEG2000 Stand alone DVR User Guide 3-2 Screen switch/OSD position adjust Press the number button to switch to the corresponding channel for its full screen view Mode: press to switch among different split modes: 4/6/8/9/13/16 splits. +/-: button to adjust the order Adjust OSD position (High/Low): Low Position: Press “MODE”+”DOWN” at the same time High Position: Press “MODE”+”UP” at the same time Note: The OSD position returns to its default level after the DVR reb
Inhaltszusammenfassung zur Seite Nr. 18
JPEG2000 Stand alone DVR User Guide 3-4-2 Freeze in Full mode In full screen mode, Press FREEZE to freeze the channel, and press FREEZE again to cancel. 3-5 View in sequence Press SEQ to enter Sequential Switch and press SEQ again to cancel. Sequence order A ＞ B ＞ C ＞ D …＞A ＞ B … Sequence time is adjustable in system s
Inhaltszusammenfassung zur Seite Nr. 19
JPEG2000 Stand alone DVR User Guide 3-6 Zoom view Go to the channel to be zoomed and press ZOOM to enlarge to 200%, use direction buttons to move the enlarged part. Use the direction buttons to choose an area and press ENTER to zoom. Press ZOOM again to cancel 3-7 Key lock After pressing “K. LOCK “, you’ll see LOCK on screen and no button is fucntioning at this time. To unlock, press and hold K.LOCK and enter Admin’spassword. Please note that r
Inhaltszusammenfassung zur Seite Nr. 20
JPEG2000 Stand alone DVR User Guide 3-8 Record Emergency record (Red): press REC to start emgergency record at continuous record mode and at the best resolution and quality. Schedule record (Green): record at the setup schedule, record mode, resolution and quality Stop record (White): the white dot shows up when the record schedule is set to “not record” at this time. Record mode mark: Alarm record: DVR records when the alarm is triggered Motion record: D
