Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTION MANUAL
Digital Single Channel Recorder
EDSR100H
V1.0
About this manual
Before installing and using this unit, please read this Manual carefully.
Be sure to keep it handy for later reference.
Inhaltszusammenfassung zur Seite Nr. 2
Safety Precautions Safety Precautions ?Refer all work related to the installation of this product to qualified service personnel or system installers. ?Do not block the ventilation opening or slots on the cover. ? Do not drop metallic parts through slots.This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service. ?Do not attempt to disassemble the appliance.To prevent electric shock, do not remove screws or covers. There
Inhaltszusammenfassung zur Seite Nr. 3
Safety Warning WARNING TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This is a
Inhaltszusammenfassung zur Seite Nr. 4
Safety Precautions Safety Precautions The lightning flash with an arrowhead symbol, within an Warning: equilateral triangle, is intended to alert the user to the presence Electrostatic-sensitive device. Use proper of uninsulated ” dangerous voltage ” within the product’s enclosure CMOS/MOSFET handing precautions to avoid that may be of sufficient magnitude to constitute a risk of electric electrostatic discharge. shock to persons The exclamation point within an equilateral triangle is Servic
Inhaltszusammenfassung zur Seite Nr. 5
Important Safeguards Important Safeguards Read Instruction---All the safety and operating instructions should be read before the init is operated Retain Instructions---The safety and operating instructions should be retained for future reference. Heed Warnings— All warnings on the unit and in the operating instructions should be adhered to. Follow Instructions— All operating and use instructions should be followed Cleaning— Unplug the unit from the outlet before cleaning. Do not use liquid clean
Inhaltszusammenfassung zur Seite Nr. 6
Table of Contents 1. Product Overview……… .… ...…………………………………………………………………………………… ..………… .. 1 1.1 Feature……… ...…… .…… .… .…………………………………… .………… ..…………………………………………… ..1 1.2 Specifications……… ....………………… .……………………………… ..………… .………… .………………………… ...2 2. Front & Rear Panels……… ...…… .……………………………………… ..………………………………………………… ....3 3. Back Panel Connections…… .……… ...…………………………………… ..………………………………………………… ..5 4. System Connection… ....……………………… ...………………………… ..…………… .…………………… .……………… ..8 4.1 One Camera Conne
Inhaltszusammenfassung zur Seite Nr. 7
Product Overview and Features 1. Product Overview The Digital Video Recorder is the first true VCR replacement designed particularly for the security industry, seamlessly combining high-resolution video multiplexing and digital recording. The Digital Video Recorder at speeds up to 60/50 fields per second with NTSC/PAL formats and replay event instantly. The Digital Video Recorder incorporates all the benefits of digital video recording, is simple to install, and operates just like a VCR. The
Inhaltszusammenfassung zur Seite Nr. 8
Specifications 1.2 Specifications Video Input 1 video input with loop through (BNC), 1Vpp/75ohm Video Output 1 video output (BNC), 1Vpp/75ohm Video Compression M-JPEG Video Resolution 720x484 (NTSC); 720x576 (PAL) CompactFlash Memory Yes, Built-in Compact Flash card slot Alarm Input Yes Alarm Output Yes Audio 2 inputs; 2 outputs Video Loss Detection Yes RS-232 9-pin female connector Event Log Yes Hard Disk Storage 3.5” IDE type, Hot- swappable Recording Mode Continuous, Time -lapse rec
Inhaltszusammenfassung zur Seite Nr. 9
Front Panel Keypads 2. Front Panel Keypads 3 4 6 7 8 19 17 18 1 2 5 EDSR100H 22 10 14 16 20 9 11 12 13 15 21 KEY 1 ~ 4 Left/Right Button: Press or to move the cursor to the left or right Up/Down Button: Press or to change the value. 5 ENTER: Press this key to confirm the selection or data changed. 6 BUZZER: Press this key to turn On/OFF the buzzer for all events. LOCK: Press and hold the LOCK button over 3 seconds to lock/unlock the function ke
Inhaltszusammenfassung zur Seite Nr. 10
16 Display: Press this key to switch ON/OFF. Record Record 002HR 002HR Disk:120 GB(0) Disk:120 GB(0) Disk size:120GB 2003/04/24 10:41:00 2003/04/24 10:41:00 Display Date/Time Display Date/Time, Display OFF And Operation status Operation Status, Disk Status. 17 HDD KEY: Protect HDD without steal 18 Hard Disk Tray: Hard Disk holder for HDD. 19 Jog and Shuttle Dial Shuttle : In Playback mode,turn the shuttle dial can fast forward/rewind the picture. In Pause mode, turn the shuttle dial can slow f
Inhaltszusammenfassung zur Seite Nr. 11
Back Panel Connections 3. Back Panel Connections 6 10 3 8 MUX MAIN 7 MONITOR IN 5 2 4 9 1 POWER Power in: The main power in. 1 AUDIO 2 Audio IN : Audio input for recording. Audio OUT : These two audio outputs can be set to “Enable” or “Disable” in Setup Menu. The operation of audio out is as follows: ( Internal circuit ) SW2 OFF / Mute SW1 Playback Audio A Audio OUT Audio IN Operation of SW2 : Operation of SW1 : When in recording or standby mode, When Playback Audio is enabled then the out
Inhaltszusammenfassung zur Seite Nr. 12
Back Panel Connections MONITOR 3 MUX MAIN MONITOR: Video input BNC connector, connected to multiplexer main monitor output. 4 MONITOR : Video output BNC connector connected to main monitor. ( Internal circuit ) SW3 MAIN MONITOR INTERNAL A MONITOR OUT VIDEO When the machine is in Menu, Search or Copy mode, the internal Video is switched to Monitor Out, so that the user can view full screen OSD. In other modes, the Video from multiplexer main monitor will be loop-through to the Monitor Out. VIDE
Inhaltszusammenfassung zur Seite Nr. 13
Back Panel Connections RS232 8 RS232 connector : Connect D-Sub 9 pins connector to RS232 ports for remote control RS485 9 RS485 connector : Cascade multi Digital Video Recorder. 10 FAN: Cooling FAN. 7
Inhaltszusammenfassung zur Seite Nr. 14
System Connection 4. System Connection 4.1 One Camera Connection. (1) (2) MUX MAIN MONITOR IN (3) Main Monitor (1 ) :Video out: The Camera Video Output is connected to the Video In at the rear panel. (2 ) : Audio Out: The camera audio output is connected to the audio input terminal at the rear panel. (3) : System Main Monitor Output: The main monitor is connected to the VIDEO OUT 1 BNC connector. Note: Please set the Multiplexer item to OFF . (NORMAL RECORD SETTING MENU) 8
Inhaltszusammenfassung zur Seite Nr. 15
System Connection 4.2 Multiplexer Connection. Multiplexer MAIN MONITOR OUTPUT VCR IN VCR OUT (2) (1) (3) MUX MAIN MONITOR IN (4) Main Monitor (1): Multiplexer VCR Out : This connects to the VIDEO IN connector at the rear panel. (2) :Multiplexer VCR In : This connects to the VIDEO OUT 1 connector at the rear panel. (3) :Multiplexer Main Monitor Output: This connects to the MUX. MAIN MONITORIN IN connector at the rear panel. (4) :System Main Monitor Out: Connect the MAIN MONITOR OUTPUT conn
Inhaltszusammenfassung zur Seite Nr. 16
System Connection 4.3 Quad Connection. ( Quad with VCR in VCR out connector) Quad MAIN MONITOR OUTPUT VCR OUT VCR IN (3) (2) (1) MUX MAIN MONITOR IN (4) Main Monitor (1): Quad VCR Out: This connects to the VIDEO INPUT connector at the rear panel. (2) : Quad VCR In: This connects to the VIDEO OUTPUT connector at the rear panel. (3) : Quad Main Monitor Out: This connects to the MUX. Main connector at the rear panel. (4) : System Main Monitor Output: Connect the MAIN MONITOR OUTPUT connector
Inhaltszusammenfassung zur Seite Nr. 17
System Connection 4.4 Quad connection. ( Quad without VCR in VCR out connector) Quad VIDEO OUT (1) MUX MAIN MONITOR IN (2) Main Monitor (1): Quad Video Out ( to Video Recorder): This connects to the VIDEO INPUT connector at the rear panel. (2): System Main Monitor Output: Connect the MAIN MONITOR connector to the main monitor. Note: Please set the Multiplexer item to OFF . (NORMAL RECORD SETTING MENU) 11
Inhaltszusammenfassung zur Seite Nr. 18
INSTALLATION 5. Installation (1) Insert a HDD (IDE) for Video Storage The HDD should be set as MASTER. ( Normally the default setting of HDD is Master) Notice: After the hard disk case is inserted into the hard disk tray, be sure to Turn the tray key in lock position. Otherwise, hard disk will not be detected and The System Loading procedure can not be completed. (2) Connect cable for video/audio input and video/audio out, The POWER LED lights if power is normal. (3) Switch Power On Th
Inhaltszusammenfassung zur Seite Nr. 19
MENU 6. MENU FLOW Turn the Jog dial clockwise or counterclockwise to change setting menu page. ALARM RECORD CLOCK/LANGUAGE SETTING MENU SETTING MENU ( See page 20 ) ( See page 14 ) ALARM RECORD SETTING MENU CLOCK/LANGUAGE SETTING MENU ALARM OPERATION : ON RECORDING SPEED 002 HR : RECORDING QUALITY : STANDARD ALARM – IN TYPE DATE : 2003/04/24 TUE : N.O. ALARM -RESET TYPE N.O. : TIME : 13:01:02 ALARM DURATION TIME : 05 SECS PRE-ALARM OPERATION O
Inhaltszusammenfassung zur Seite Nr. 20
MENU 6.1 CLOCK/ LANGUAGE SETTING MENU CLOCK/LANGUAGE SETTING MENU : 2003/04/24 TUE DATE : 13:01:02 TIME : ENGLISH MENU LANGUAGE VERSION: 1.0 (2003/05/26) In CLOCK/LANGUAGE SETTING MENU , we SET (1) DATE : Current date Year: 2000 ~ 2099 Month: 01~ 12 Date: 01~31 (2) TIME : Current time Hour: 00 ~ 23 Minute : 00 ~ 59 Second: 00 ~ 59 (3) MENU LANGUAGE: ENGLISH Left/Right Button: Press or to move the cursor to the left or right Up/
