Inhaltszusammenfassung zur Seite Nr. 1
L L
E E
A A
R R
N N
II
N N
G G
™
Infant-to-Toddler Rocker
Infant Seat Toddler Seat
Model Number: G5911
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
Please keep this instruction sheet, as it contains important information.
Use the upright position only when your child has developed enough upper body control to sit without leaning forward.
Always use the restraint until your child is able to climb in and out of the chair unassisted.
Adult assembly is required. Tool needed for assembl
Inhaltszusammenfassung zur Seite Nr. 2
Warning Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. The kickstand is WARNING packaged within the pad at the factory. Before beginning assembly, please remove kickstand from the pad. To prevent serious injury or death: • It is dangerous to use this product on an elevated surface. •Never use on a soft surface (bed, Toy Bar Pad sofa, cushion) since product can tip over and cause suffocation in soft surfaces. 3 Toys • Always use the restraint until
Inhaltszusammenfassung zur Seite Nr. 3
Press Tabs Side Rail Sockets Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp 3 #8 x 1.9 cm ( /4") Screw edges. DO NOT use if any parts are missing or broken. Shown Actual Size Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Cross Brace CAUTION This package contains small parts in its unassembled state. Adult assembly is required. 2 Side Rails • Insert a screw through the hole in the bot
Inhaltszusammenfassung zur Seite Nr. 4
Assembly Side Rail Side Rail Hole Front Tube Side Rail Front Tube Vibrations Unit Side Rail 5 4 Hole 1 #8 x 3 cm (1 /8") Screw 1 •Locate the hole in each side rail. •Insert a #8 x 3 cm (1 /8") Shown Actual Size •With the vibrations unit facing forward, fit the front tube screw through the to the side rails, as shown. Hold the front tube in place outside of each side rail and and proceed to step 5. into the ends of the front tube. IMPORTANT! Please follow the next assembly (step 6) carefully to
Inhaltszusammenfassung zur Seite Nr. 5
Assembly Retainer with Lock Nut Kickstand Press Press Tab Tab Rounded Side 6 Receptacles 7 M4 Lock Nut - 2 (Inside Retainer) •Fit a retainer with lock nut Shown Actual Size onto the end of the screw •Position the assembly face down, as shown. and to the inside of a •While pressing the tab on each end of the kickstand, side rail. insert the kickstand into the receptacle in each side rail, as shown. •Push the kickstand into the receptacles until the Hint: A lock nut has been factory assembled t
Inhaltszusammenfassung zur Seite Nr. 6
Assembly Pad Pad Slot Press Seat Back Seat Back Tube Hardboard 8 9 Side Rail •Turn the assembly upright. •Fit the upper pocket on the pad onto the seat •Turn the hardboard back tube. over and insert it into •Fasten the pad buckles the slot in the front around each side rail. Pad edge of the pad. Buckles •Fasten the pad buckles on the front edge of the pad Pad and underneath the seat. Make sure you hear a “snap” on Buckles both sides. •Press the fasteners together in the seat back portion of
Inhaltszusammenfassung zur Seite Nr. 7
Battery Installation Battery Safety Information 1.5V LR20 "D" + – SHOWN ACTUAL SIZE Batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different Battery types: alkaline, standard (carbon-zinc) or rechargeable Compartment (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Locate the battery compartment on the bottom of the • Remove batteries during long
Inhaltszusammenfassung zur Seite Nr. 8
Set-Up & Use Securing Your Infant IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp WARNING edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. To prevent serious injury or death: • Always use the restraint until child is able to climb in and out of the WARNING chair unassisted. • It is dangerous to use this product To prevent serious injury or dea
Inhaltszusammenfassung zur Seite Nr. 9
Securing Your Infant Toys Anchored End Anchored End Strap B Strap Strap B Toy Free End Toy Free End 3 Tighten Loosen To tighten the belts: •Feed the anchored end of the restraint belt up through the buckle to form a loop . 4 B •Pull the free end of the restraint belt . Toy •Repeat this procedure to tighten the other restraint belt. To loosen the belts: •Feed the free end of the restraint belt up through the •Fit the pad straps through buckle to form a loop . Enlarge the loop by pulling on the sl
Inhaltszusammenfassung zur Seite Nr. 10
Toy Bar Calming Vibrations Toy Bar Plug Plug 6 Toys Power Switch •Make sure your child is properly secured in the seat. •Slide the power switch to the on position for calming vibrations. •Slide the power switch to the off position to turn vibrations off. 5 •Fit the plugs on each end of the toy bar into the sockets in each side rail. •Fit the toy bar straps through the slot in the toy rings. Fasten the straps. •Or, attach the toys to the pad straps (see Step 4). Hint: Pull the monkey’s
Inhaltszusammenfassung zur Seite Nr. 11
Kickstand Storing the Restraint System for Toddler Use Small Slot Small Slot Large Slot 7 Kickstand 8 •Rotate the kickstand out. • Insert the restraint belts back through the small slots in •Push down on the seat bottom to be sure the kickstand the pad. is in position. • Insert the restraint pad down through the large slot in the pad. 9 •Turn the rocker face down. •Tuck the ends of the restraint pad underneath the buckles, as shown. 11
Inhaltszusammenfassung zur Seite Nr. 12
Care The frame, pad toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2004 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA G5911pr-0726
