Inhaltszusammenfassung zur Seite Nr. 1
OWNER'S MANUAL
DC-1200A Dust Collector
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840
www.jettools.com e-mail jet@jettools.com M-708634 02/02
Inhaltszusammenfassung zur Seite Nr. 2
This manual has been prepared for the owner and operators of JET’S DC-1200A. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your Dust Collector, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully. Warranty & Service
Inhaltszusammenfassung zur Seite Nr. 3
WARNING 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this machine until proper training and knowledge has been obtained. 2. Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before servicing. 3. Do not use outdoors or on wet surfaces. 4. Do not allow to be used as a toy. Close attention is necessary when used near children. 5. Use only as described in this manual. Use only manufacturer’s recommen
Inhaltszusammenfassung zur Seite Nr. 4
Specifications: DC-1200A-1 DC-1200A-3 Stock Number.................................................... 708634 ............................................................... 708635 Blower Wheel Diameter..................................... 12".............................................................................12” Sound Rating at 3 feet....................................... 80-85 db ........................................................... 80-85 db Hose Diameter.......................
Inhaltszusammenfassung zur Seite Nr. 5
WARNING Read and understand the entire contents of this manual before attempting assembly or operation of the dust collector! Failure to comply may cause serious injury! Unpacking 1. Finish removing all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton 1 Bag Hanger 1Base 1 Plastic Cover 1 Hanger Bracket 1Hose 1 Owner's Man
Inhaltszusammenfassung zur Seite Nr. 6
Assembly 1. Install four casters to the under side of the base as pictured in Fig. 1. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B, Fig. 1) against the base with a 9/16” or 14mm wrench. This will give the caster proper clearance. 2. Place the base with casters on the ground. Attach the motor and fan assembly (A, Fi
Inhaltszusammenfassung zur Seite Nr. 7
4. Attach three support brackets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand tighten only at this time. 5. Install the housing (A, Fig. 5) to two support brackets using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (B, Fig.5). Be sure hose opening faces fan housing. Before attaching third support bracket place the hanger bracket (C, Fig.5) between the support bracket and the housing. Tighten all nuts and bolts at thi
Inhaltszusammenfassung zur Seite Nr. 8
7. Slide the bag hanger hook (A, Fig. 7) through the top loop of the filter bag. Insert the hanger into the hanger bracket. Thread the retainer strap (B, Fig. 7) through the loops on the filter bag (C, Fig.7), and fasten to the collector housing. The retainer strap should be tight enough to provide a good seal. 8. Insert the ring (A, Fig. 8) of the collector bag into the bottom of the housing at an angle. Pull down on the bag to make sure it “seats” in the housing. Electrical Connections WARNING
Inhaltszusammenfassung zur Seite Nr. 9
Maintenance 5. Turn the bag outside in and insert into the housing. WARNING Never perform maintenace on this machine before turning switch off and removing plug Use the proper type hose to connect the dust from power source, unplug. collector to the machine being operated. Dryer Failure to comply may cause serious injury! vent hose is not acceptable for this purpose. Contact your nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories. Customize your installation an
Inhaltszusammenfassung zur Seite Nr. 10
Parts Breakdown 10
Inhaltszusammenfassung zur Seite Nr. 11
Parts List for the DC-1200A Index Part No. No. Description Size Qty. 1..........411035W ..................... Impeller Housing.................................... ...............................................1 2..........411026W ..................... Motor Bracket ........................................ ...............................................1 3..........998621......................... Strain Relief........................................... ...........................................
Inhaltszusammenfassung zur Seite Nr. 12
Wiring Diagram For 3 Phase 230V/460V Dust Collector Wiring Diagram For Single Phase 230V Only Dust Collector 12
