Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTION MANUAL
2 H.P. Single-Stage
Dust Collector
(Model 50-851)
PART NO. 902114 - 07-01-02
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Inhaltszusammenfassung zur Seite Nr. 2
GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust
Inhaltszusammenfassung zur Seite Nr. 3
ADDITIONAL SAFETY RULES FOR DUST COLLECTORS WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. 1. DONOTOPERATE THIS MACHINE until it is 14. DO NOT use the dust collector as a toy. DO NOT assembled and installed according to the instructions. use near or around children. 2. OBTAIN ADVICE FROM YOUR SUPERVISOR, 15. DO NOT insert fingers or foreign objects into the instructor, or another qualified person if you are not dust intake port or discharge port. Keep hair, loose f
Inhaltszusammenfassung zur Seite Nr. 4
UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND MAY BE
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. ASSEMBLING CASTER B C ASSEMBLIES TO BASE 1. Align the holes in swivel caster assembly (A) Fig. 4, with four holes in caster bracket (B) located on the underside of base (C). Place a 5/16" lockwasher (E) Fig. 4 onto a 5/16-18x5/8" hex head screw (D), then place a 5/16" flat washer (F) onto the hex head screw. Ins
Inhaltszusammenfassung zur Seite Nr. 6
5. Place ten-hole rubber gasket (J) Fig. 8, on blower J flange (H). Align holes in gasket with mounting holes in blower flange and press gasket onto flange as shown. H Fig. 8 K A J 6. Align mounting holes in chute (K) Fig. 9, with holes Fig. 9 in gasket (J), which was assembled in STEP 5. Place a 5/16" lockwasher onto a 5/16-18x5/8" hex head screw, insert screw through the chute and gasket, thread the screw into the motor assembly, and tighten securely. Repeat this process for the 9 remaining ho
Inhaltszusammenfassung zur Seite Nr. 7
8. Align mounting holes in drum (N)Fig. 12, with N gasket (M), which was assembled in STEP 7. Place a K 5/16" lockwasher onto a 5/16-18x5/8" hex head screw, insert screw (P) Fig. 13 through chute (K), thread screw M into drum (N) and tighten securely. Repeat this process for the seven remaining holes. Fig. 12 9. Assemble “U” bracket (R) Fig. 14, to side of drum (N). Place a 5/16" lockwasher then a 5/16" flat washer onto the 5/16-18x5/8" hex head screw. Insert the hex head screw through the hole
Inhaltszusammenfassung zur Seite Nr. 8
12. Assemble the other end of drum support arm (T) Fig. 16, to base (B). Place a 5/16" lockwasher onto a 5/16-18x5/8" hex head screw (W), insert the hex head T screw through drum support arm (T), and thread into base (B). Repeat this process for the remaining hole. NOTE: Do not completely tighten mounting hardware at this time. B 13. Assemble the remaining drum support arm to the opposite side of drum and base in the same manner. W Tighten all mounting hardware. Fig. 16 14. Fig. 17, illustrates
Inhaltszusammenfassung zur Seite Nr. 9
A F F G 3. Position open end of filter bag (A)Fig. 20, over E upper lip of support drum (E). Insert locking band (F) Fig. Fig. 20 20, through the loops of filter bag (A) and fasten with clamp (G) as shown inFig. 21. NOTE:Make certain locking band (F) Fig. 20, is positioned in the channel of drum (E) before fastening clamp (G) Fig. 21. G 4. Pull up on each retaining clip (A) Fig. 22, and insert the dust collection bag (B) underneath each retaining clip to hold the dust collection bag in place. 5
Inhaltszusammenfassung zur Seite Nr. 10
3. Three dust intake port caps (D) Fig. 25, are supplied with the dust collector. NOTE:These caps should be inserted into the intake ports as shown, when they are D not in use. WARNING: DO NOT INSERT FINGERS OR ANY FOREIGN OBJECT INTO THE DUST INTAKE PORTS WHEN UNIT IS OPERATING. Fig. 25 CONNECTING MACHINE TO POWER SOURCE ELECTRICAL CONNECTIONS A separate electrical circuit should be used for your MINIMUM GAUGE EXTENSION CORD tools. This circuit should not be less than #12 wire and RECOMMENDED S
Inhaltszusammenfassung zur Seite Nr. 11
OPERATING CONTROLS ON/OFF SWITCH The “on/off” switch is located on the side of the motor. To turn the dust collector “ON”, push the start button (A) Fig. 27. To turn the dust collector “OFF”, push stop button (B). A LOCKING SWITCH IN THE “OFF” POSITION B IMPORTANT: When the machine is not in use, the switch (A) Fig.18 should be locked in the OFF position using a padlock with a 3/16" diameter shackle to prevent unauthorized use. Fig. 27 MAINTENANCE WARNING: Before any maintenance or service is pe
Inhaltszusammenfassung zur Seite Nr. 12
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) ARIZONA ILLINOIS MINNESOTA Cleveland 44125 Minneapolis 55429 Tempe 85282 (Phoenix) Addison 60101 (Chicago) 8001 Sweet Valley Drive 5522 Lakeland Avenue North 2400 West Southern Avenue 400 South Rohlwing Rd. Unit #
