Inhaltszusammenfassung zur Seite Nr. 1
Installation Instructions
®
Renaissance Built-in Dishwasher
Models RDW24S and RDW24I
Part No. 105671 Rev. B
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Important Safety Instructions .........................1 Installation Instructions ...................................8 About Safety Instructions ................................1 Verify the Package Contents ...........................8 Safety Symbols and Labels ............................1 Installation Preparation ...................................9 General Safety Precautions ............................2 Installing the Unit in the Cabinet ...................13 Product Speci
Inhaltszusammenfassung zur Seite Nr. 3
Important Safety Instructions Important Information About Safety Symbols and Labels Safety Instructions DANGER • The Important Safety Instructions and Immediate hazards that WILL result in severe warnings in these instructions are not meant personal injury or death. to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or WARNING any other appliance. Hazards or unsafe practices that COULD result in • A
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Instructions General Safety Precautions WARNING - To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING WARNING • Use this dishwasher only for its intended • Do not tamper with the controls. purpose as outlined in the use and care • This appliance is designed for installation by manual. It is not intended for commercial use. more than one person. To avoid personal i
Inhaltszusammenfassung zur Seite Nr. 5
Product Specifications Product tolerances: ±1/16” (±1.6 mm) Product Dimensions Style varies, model RDW24S shown Depth with door open 49 3/4” (126.4 cm) D Handle depth Depth with door closed A C Drain hose Depth dimensions allow Side for hose on back of unit Front B 6 1/4” (15.9 cm) to 8 1/4” (21.0 cm) Shipping weight: 117 lbs. (53 Kg) 1 15/16” (4.9 cm) Model Description A B C D 1 ® Stainless steel 24” 34 3/8” (87.4 cm) to 22 7/8” Epicure : 2 1/2” (6.4 cm) RDW24S 2 ® front panel (61.0 cm)
Inhaltszusammenfassung zur Seite Nr. 6
Preparing for Installation Grounding Instructions for a WARNING Permanently Connected Appliance Observe all governing codes and ordinances during This unit must be grounded to operate properly. It planning and installation. Contact your local building must be connected to a grounded metal, permanent department for further information. wiring system, or an equipment-grounding conductor must be run with the circuit conductors and Electrical Specifications connected to the equipment groundi
Inhaltszusammenfassung zur Seite Nr. 7
Preparing for Installation Cutout tolerances: +1/16” (+1.6 mm), -0 Preparing the Location WARNING Follow all cabinet dimensions shown to insure safe operation. All minimum product dimensions must be met or exceeded (see page 3). Dimensions shown provide the required clearances. 2” (5.1 cm) • The cabinet must enclose the dishwasher on the top, back and both sides. F • Carefully check the location where the 4” (10.2 cm) dishwasher is to be installed. Put it in a location with convenient a
Inhaltszusammenfassung zur Seite Nr. 8
Preparing for Installation Custom Door Panel/Handle for Preparing the Drain Model RDW24I CAUt ION • The custom panel mounting screws are provided with the dishwasher. Follow the template included Keep the factory installed high loop drain hose in to ensure that the panel and the accompanying place to ensure proper dishwasher operation. Do fasteners will fit properly. not modify or move the mounting bracket in any manner. If it is necessary to lengthen the hose, • The handle and hand
Inhaltszusammenfassung zur Seite Nr. 9
Preparing for Installation Disposer Disposer connection connection Air gap 2” dia. max. 2” dia. max. Keep higher Keep higher than disposer than disposer 35” connection connection 20” min. 35” max. max. 20” min. Sink trap Sink trap Floor Floor Disposer Installation without Air Gap Disposer Installation with Air Gap Waste tee Waste tee Air gap 2” dia. max. 2” dia. max. Keep higher Keep higher than waste tee than waste tee connection 35” connection 35” 20” min. max. 20” min. Sink trap
Inhaltszusammenfassung zur Seite Nr. 10
Installation Instructions Verify the Package Contents • Remove all styrofoam and plastic wrap from the A dishwasher. Be sure to remove the toe kick from the top of the dishwasher packaging. With the assistance of at least one person, remove the dishwasher from the shipping pallet. Place the unit to the side of the cabinet opening. NOt E: Since each dishwasher is tested at the factory C B for proper operation, there may be some residual water inside the unit, the water supply line or dra
Inhaltszusammenfassung zur Seite Nr. 11
10 7/8” 10 7/8” (26.6 cm) (26.6 cm) Installation Instructions Installation Preparation WARNING • Before working on wiring for any electrical appliance, be sure the power has been turned 3/8” screw, off at the breaker/fuse box. Place a tag at included, the disconnect switch indicating that you are 2 places working on the circuit. • Moving this appliance requires two people. Do not attempt to install or lift it alone. C • To prevent personal injury, wear hand protection L when m
Inhaltszusammenfassung zur Seite Nr. 12
Installation Instructions Custom Door Panel Installation (cont.): 3. To make small tension adjustments to the spring, hold the back end of the spring with one 5. Open the door slightly and use the six (6) hand and turn the front part one or more times. supplied 1 3/4” screws to secure the panel to the Turn it clockwise to increase spring tension, door through the back. counterclockwise to reduce tension. 6. Slide the bottom of the door frame up until the black trim around the exhaust ven
Inhaltszusammenfassung zur Seite Nr. 13
Installation Instructions 6. Reattach the front end of the spring by pulling it 2. Measure the height of the front and back of the up and forward to fasten it in the mount. cutout with a tape measure. 3. Adjust the feet, until the front of the dishwasher measures 1/8” (3.0 mm) shorter than the cutout height. 7. Open the door and check the spring tension again. If necessary, make further adjustments. Leveling the Dishwasher 4. Open the door and pull the bottom rack out of the dishwasher. Che
Inhaltszusammenfassung zur Seite Nr. 14
Installation Instructions 7. Connect the ground (green) wire on the cable Connecting the Wiring using a loop or spade terminal to the ground Permanently Connected Appliance Only: connection screw located on the dishwasher chassis. If the cord is not long enough, or if a hard-wire installation is needed, follow the steps below to Junction To house power complete the electrical connection. Otherwise skip box supply to Installing the Unit in the Cabinet. NOt E: When doing a hard-wire insta
Inhaltszusammenfassung zur Seite Nr. 15
Installation Instructions Installing the Unit in the Cabinet Water Line Connection 1. Position the dishwasher in front of the cutout. CAUt ION Make sure the drain hose, water supply line and power cable are positioned in the utility cutouts • The unit has a float switch in the base pan and are routed to the side they will be connected. to protect against flooding. If the inlet valve connection on the dishwasher is not seated properly, water may leak into the base pan and activate the fl
Inhaltszusammenfassung zur Seite Nr. 16
Installation Instructions 5. Check again that the entire length of the power Drain Line Connection cable, water line and drain hose are free of pinches or kinks. CAUt ION 6. Verify that the dishwasher is level front to back and side to side inside the cutout. Re-level if • For proper dishwasher operation and drainage, necessary before testing the unit. the drain line must be routed through the bottom of the cabinet and up to the drain or air gap Wet Test Checklist connection. The drain
Inhaltszusammenfassung zur Seite Nr. 17
Installation Instructions Final Leveling Attaching the Anti-tip Brackets 1. Check to make sure that adjacent drawers and CAUt ION cupboards can be opened when the dishwasher door is open. Reposition the dishwasher if Make sure to anchor one anti-tip bracket on each necessary. side of the dishwasher. 2. Check that there is a 1/8” (3.0 mm) space 1. The anti-tip brackets protect against possible between the top of the dishwasher door and the tipping caused by heavy bottom rack loads on und
Inhaltszusammenfassung zur Seite Nr. 18
Installation Instructions Installing the Toe Kick Installation Checklist 1. Loosen the brackets for the toe kick by moving the gray catches toward the center of the WARNING dishwasher. • To ensure a safe and proper installation, the following checklist should be completed by the Catch installer to ensure that no part of the installation has been overlooked and the unit is working properly. • Proper installation is the responsibility of the homeowner. The importance of proper installati
Inhaltszusammenfassung zur Seite Nr. 19
Inhaltszusammenfassung zur Seite Nr. 20
Item No., 80 933 28 Rev. 02 Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www .dacor .com
