Inhaltszusammenfassung zur Seite Nr. 1
PATIODOORSYSTEMS
®
Therma-Tru
Hinged Patio
Door System
Single Panel
Unit Assembly
Read all instructions before starting.
The applicable standards for these products are governed by
the International Residential Code.
Copies of performance ratings and testing are available on our website
www.thermatru.com and our product manual.
Inhaltszusammenfassung zur Seite Nr. 2
Part identification Not all parts shown will be included in package. Parts will vary for type of unit purchased. Door Bottom - Adjustable Hinge Standard Hinge Inswing Door Panel Door Bottom - Transport Clip Outswing Head Jamb Head & Lock Hinge Multi-point Lock Weatherstrip Weatherstrip Strikes Inswing Flange Outswing Flange Standard Strike End Seal Pad Inswing Lock Hinge Inswing sill Outswing Sill Jamb Jamb 1
Inhaltszusammenfassung zur Seite Nr. 3
Part identification - continued #6 x 3/4” #10 x 3/4” flat head screw flat head screw #8 x 5/8” #8 x 3/4” flat head screws flat head screw #8 x 1-1/4” #8 x 2” flat head screw flat head screw #8 x 3/4” #10 x 2-1/2” wafer head screw flat head screw Tools/materials required This is a listing of tools that may be required to assemble unit. • Drill/screw gun Phillips head drive bit or screwdriver #2 & #3 Silicone sealant and caulk gun Utility knife Rubber mallet Hammer Staple gun with 1/2”
Inhaltszusammenfassung zur Seite Nr. 4
NOTE: A large work area is needed to assemble the frame kit. Cover area with cardboard from one or more door panel cartons to protect frame parts and floor. If available a carpeted table can be used to avoid marring prefinished surfaces. REMOVE COMPONENTS FROM PACKAGING 1 NOTE: Product that is purchased with the multi-point lock system will have additional instructions in the handle hardware box. Installation instructions will be included in the site package. ATTACH HINGES TO DOOR 2 Standa
Inhaltszusammenfassung zur Seite Nr. 5
ATTACH HINGES TO DOOR - continued 2 Adjustable Hinge Option “H” marked hinge shown Attach hinge to door Marking Locate the “H” and “V” markings on hinges. The two “H” hinges go in top and bottom locations with the “V” hinge in the center. For 8’, the “V” hinge is located second from top of door. Insert thick side of hinge into pocket in door and fasten with #8 x 1-1/4” flat head screws. NOTE: Inswing hinges are reversible by removal of hinge pin. Outswing #8 x 1-1/4” hinges are reversible by r
Inhaltszusammenfassung zur Seite Nr. 6
INSTALL WEATHERSTRIP 4 Apply Weatherstrip to Active Frame Parts Press in kerf with hand. Head Jambs Align starting end with head gain. Fit and secure in place along full length. Long Reach Trim finish end flush with endofjamb. Head Jamb Hinge Jambs Align starting end with head gain. Short Reach Fit and secure in place along full length. Hinge Jamb Lock Jambs Align starting end with head gain. Long Reach Fit and secure in place along full length. Lock Jamb Trim Bottom End 3/8" 11/32” Trim weather
Inhaltszusammenfassung zur Seite Nr. 7
INSTALL STRIKES 5 Standard Strike Option - Inswing NOTE: Adjustable security Outswing units will have strike backing installed during unit installation. plate Slide Strike Assembly onto Lock Jamb Lock jamb Lightly bend tongue area of backing plate inward to allow for a snug fit then slide over edge of lock jamb into mortise. Fasten Security Strike (2) #9 x 3/4” flat head screws Assembly to Lock Jamb or (2) 16 gauge Fasten with (2) #9 x 3/4" flat head 1/2” x 7/16” crown staples screws or (2) 16
Inhaltszusammenfassung zur Seite Nr. 8
ATTACH HINGES TO JAMB 6 NOTE: These are instructions for installation of standard hinges. Proceed to step 7, FRAME ASSEMBLY, if using adjustable hinges. Standard Hinge Option Leave Holes Vacant Fasten Hinges to Hinge Jamb Place hinges into hinge mortise. Pre-drill 1/8” dia. pilot holes through jamb. Fasten top hinge with (2) #10 x 3/4” flat head screws in hole locations shown. Fasten middle and bottom hinges each with (3) #10 x 3/4” flat head screws leaving top hole vacant. #10 x 3/4" CAUTION: f
Inhaltszusammenfassung zur Seite Nr. 9
FRAME ASSEMBLY 7 Fasten Side Jambs to Head Jamb #10x21/2” Butt and align head jamb to side jambs. flat head screws Pre-drill 1/8” dia. pilot holes through side jamb into head jamb. Fasten side jambs to head jamb with (3) #10 x 2 1/2” flat head screws through lock and hinge jamb into head jamb. Inswing Sill Option Apply End Seal Pads End seal pad Remove from paper backing and apply adhesive side of end seal pads at bottom of each jamb. Sealant Caulk Entire Sill Gain Apply a 1/4" bead of sealant
Inhaltszusammenfassung zur Seite Nr. 10
FRAME ASSEMBLY - continued 7 Outswing Sill Option Partially Set Sill Screws in Jambs Drive (1) #8 x 2” flat head screw through holes in both side jambs until tips barely protrude through jamb face. Flat head screw #8 x 2” Caulk Entire Sill Gain Apply a 1/4” bead of sealant to sill gain and a bead that matches upper profile of sill. Sealant Fasten Sill to Jamb Use screw points and index sill in place. Drive screws using bit sized properly for screw head. Pre-drill (2) 3/32” dia. pilot holes t
Inhaltszusammenfassung zur Seite Nr. 11
Top Flange FLANGE INSTALLATION 8 Inswing Outswing NOTE: Inswing application shown. Align and Install Side Flanges Align edge of side flange with bottom of side jambs. Firmly press into kerf in jamb using a rubber mallet if necessary. Align Flange will be set back approximately 1/2” from top edge of jamb. Install Top Flange Center top flange into head jamb kerf and press into place using a rubber mallet if necessary. 10 Side Flange Side Flange
Inhaltszusammenfassung zur Seite Nr. 12
DOOR INSTALLATION 9 Standard Hinge Option Make 2 “Insert Skids” 38" 2" Make from 2 x 6 boards. 3" For 6-9/16" jambs For 4-9/16" jambs 3/8" NOTE: It is recommended 12-1/8" to cover skids with 2x6 cardboard or other material to protect surface of door. Place Door into Frame Hinge Lay frame on flat surface with hinges on jamb pointed up as shown. Slide door down on top of skids. Skid (2) Door Frame Door Skid Hinge 4-9/16" Jambs Jamb Door Skid Hinge 6-9/16" Jambs Jamb 11
Inhaltszusammenfassung zur Seite Nr. 13
DOOR INSTALLATION - continued 9 Engage Hinge Knuckles Tap with hammer or rubber mallet as required to line up hinge knuckles and engage. Install Hinge Pins Hinge Pin Door Tap in pins. Be certain to insert pins so heads are on top edges of hinges. Door Frame Adjustable Hinge Option Fasten door panel to frame Prop up hinge side of door panel until hinges can align into mortises on hinge jamb. Fasten door panel to #8 x 3/4” flat head frame with #8 x 3/4” screws flat head screws, (2) in top hinge
Inhaltszusammenfassung zur Seite Nr. 14
ATTACH TRANSPORT CLIP 10 Standard Lock Option Transport Clip Attach Transport Clip to Door Insert tab into latch bore. Exterior Position reference lip at edge of side stile against exterior side of door. Fasten with (2) #6 x 3/4” flat head screws. #6 x 3/4" flat head screws #6 x 3/4” Attach Transport Clip to Transport Clip Frame Close door into frame ensuring margins are even at head jamb. Fasten transport clip to frame with (2) #6 X 3/4” flat head screws. #6 x 3/4" flat head screws Multi-poin
Inhaltszusammenfassung zur Seite Nr. 15
ATTACH TRANSPORT CLIP - continued 10 Attach Transport Clip to Door Place flattened transport clip on top of door approximately 1 to 2 inches from lock side edge. #6 x 3/4" flat head Fasten with (2) #6 x 3/4” flat head screws. screws Attach Transport Clip to Frame Close door into frame ensuring margins are even at head jamb. Fasten transport clip to frame with (2) #6 x 3/4” flat head screws. #6 x 3/4" flat head screws UNIT READY FOR INSTALLATION 11 Unit can now be transferred for installation.
Inhaltszusammenfassung zur Seite Nr. 16
PATIODOORSYSTEMS 1687 Woodlands Dr. Maumee, OH 43537 1-800-THERMATRU (843-7628) www.thermatru.com © 2004 Therma-Tru Corp. Therma-Tru Doors is an operating company of Fortune Brands, Inc. 03-01-04 Part # AIHPSNGL
