Inhaltszusammenfassung zur Seite Nr. 1
GE Model 19208
www.jascoproducts.com
Wireless Door Chime Kit
Installation Instructions for Battery Operated
Wireless Door Chime Kit
Prior to Installation the Try-Me feature must be removed.
1. Remove the battery cover on the chime.
2. Unplug the red and white wires inside the battery compartment.
3. Remove the battery pack and discard appropriately.
Required Tools: Small flat blade screwdriver, drill, drill bit,
Inhaltszusammenfassung zur Seite Nr. 2
Single Push Button Kit: If you purchased a kit with a single push button, the chime tune will be set to Ding Dong from the factory. Dual Push Button Kit: If you purchased a kit with two push buttons, one push button will be set to Ding Dong and the other push button will be set to Westminster from the factory. The following instructions explain how to change the tune on any wireless push button. 1. Remove the battery from the push button transmitter. 2. Locate the 9 position jumpe
Inhaltszusammenfassung zur Seite Nr. 3
Parking the jumper on an open set of pins. The two jumpers on the left are in the parked position. Setting The House Security Code Each chime component has jumpers for setting the house security code. In most cases you will not need to change the factory settings for the security code. If your chime activates intermittently or does not work at all, you may be able to solve the problem by changing your security code.
Inhaltszusammenfassung zur Seite Nr. 4
The chime and pushbutton must be set to the same house security code for the combination to operate together. Note: The push button has 3 additional jumpers that are used to set the chime tune that will play. The chime tune jumpers do not affect the house security code. 1. Remove power or batteries from the chime. 2. To remove the batteries from the pushbutton, open the pushbutton case as shown below. 3. Locate the House Security Code door and screw located on the back
Inhaltszusammenfassung zur Seite Nr. 5
Push Button Jumpers Chime Jumpers 5. Jumpers 1-6 are used to select 1 of 64 possible home security codes. 6. To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation. Positions 1-6 on the chime and pushbutton must match exactly. Push Button Mounting Instructions Note: Avoid mounting the push button on metal surfaces, a
Inhaltszusammenfassung zur Seite Nr. 6
b. Replacing the back cover 1. Push buttons are typically mounted at the same height as the door knob or handle (between 36" and 44" above the floor). 2. Before mounting, choose a mounting location that is not farther than 150 feet from the chime unit location. Not farther than 150 feet Place push button where you would like to mount and test operation with the chime as close to it’s final location as possible. If it works, mount button here. Do not mount in an area
Inhaltszusammenfassung zur Seite Nr. 7
3. Use back cover of push button as a template to mark two screw holes. 4. Drill two holes with 3/32” drill in marked locations. 5. Secure back cover to the mounting surface with two supplied mounting screws. 6. Press front housing onto back cover. 7. Test Operations, if chime does not work, see TROUBLESHOOTING. Chime Unit Mounting Instructions Note: Avoid mounting the push button on metal surfaces, as it may result in a reduced range of transmission. 1. Select chime mo
Inhaltszusammenfassung zur Seite Nr. 8
6. Place the chime unit’s keyhole slots over the screws and press down on the chime unit to secure it. Operation 1. Slide power switch to “On” to turn on the chime. 2. Gently press transmitter button to sound chime.
Inhaltszusammenfassung zur Seite Nr. 9
Troubleshooting Chime doesn't work: 1. Make sure push button switch is depressed and held for at least 1 second. 2. Make sure plastic tag is removed from battery. 3. Make sure house code switches 1-6 on chime and push button match exactly. 4. Verify battery orientation in push button. 5. Try fresh batteries. 6. Make sure chime is not farther than 150 feet away from push button. 7. Ensure push button is not mounted on metal, near metal studs, or near the
