Inhaltszusammenfassung zur Seite Nr. 1
Model 19242
www.jascoproducts.com
Wireless Door Chime Kit
Installation Instructions for Battery Operated
Wireless Door Chime Kit
Prior to Installation the Try-Me feature must be removed.
1. Remove the battery cover on the chime.
2. Remove the white Styrofoam block
3. Unplug the red and black wires inside the battery compartment.
4. Remove the battery pack and discard appropriately.
House Code
Door
Styrofoam
Bl
Inhaltszusammenfassung zur Seite Nr. 2
Chime (receiver) Push-Button (Transmitter). Chime Tune Setting The chime tune is set by adjusting the dip switches located in the push button. The default setting is “Ding Dong” The following instructions explain how to change the tune on any wireless push button. 1. Remove the battery from the push button transmitter. 2. Locate the 3 dip switches shown below. 3. Select the desired chime sound from the table below. ON: Switch On OFF:
Inhaltszusammenfassung zur Seite Nr. 3
- House Code Jumpers Chime Dip Switches (Ding Dong Shown) Pushbutton Dip Switches and Jumpers Setting The House Security Code Each chime component has 4 jumpers for setting the house security code. In most cases you will not need to change the factory settings for the house security code. If your chime activates intermittently or does not work at all, you may be able to solve the problem by changing your security code. 1. Remove power or batteries
Inhaltszusammenfassung zur Seite Nr. 4
back of the chime (See the chime components picture above). Remove the screw and take off the door. 4. Locate the chime and pushbutton jumpers shown below. House Code Jumpers Chime and Pushbutton Jumpers 5. To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation. The jumpers on the chime
Inhaltszusammenfassung zur Seite Nr. 5
Push Button Mounting Instructions Note: Avoid mounting on metal surfaces, as it may result in a reduced range of transmission. Do not mount in an area where exposed to direct rain. a. Removing the back cover b. Replacing the back cover 1. Push buttons are typically mounted at the same height as the door knob or handle (between 36" and 44" above the floor). 2. Before mounting, choose a mounting location that is not farther than 150 feet from the chime unit location.
Inhaltszusammenfassung zur Seite Nr. 6
Not farther than 150 feet Place push button where you would like to mount and test operation with the chime as close to it’s final location as possible. If it works, mount button here. If it does not work, see TROUBLESHOOTING. 3. Use back cover of push button as a template to mark two screw holes. 4. Drill two holes with 1/16” drill in marked locations. 5. Secure back cover to the mounting surface with the 3x20mm screws. 6. Press front housing onto back cover. 7.
Inhaltszusammenfassung zur Seite Nr. 7
Chime Unit Mounting Instructions Note: Avoid mounting on metal surfaces, as it may result in a reduced range of transmission. 1. Select chime mounting location. 2. Use the supplied chime template to mark mounting holes. 3. Drill 5/32” holes at marked locations. 4. Insert supplied wall anchors into the holes. 5. Insert the 4/20mm screws into the anchors, setting the screw heads extending about 1/4" from mounting surface. 6. Place the chime unit’s keyhole slots over
Inhaltszusammenfassung zur Seite Nr. 8
1. Slide power switch to “On” to turn on the chime. 2. Gently press transmitter button to sound chime. Troubleshooting Chime doesn't work: 1. Make sure push button switch is depressed and held for at least 1 second. 2. Make sure house code switches 1-4 on chime and push button match exactly. 3. Verify battery orientation in push button. 4. Try fresh batteries. 5. Make sure chime is not farther than 150 feet away from push button. 6. Ensure push button is not mounted on metal, n
Inhaltszusammenfassung zur Seite Nr. 9
or www.jascoproducts.com Made in China Hecho en China Distributed by: Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. www.jascoproducts.com 19242
