Inhaltszusammenfassung zur Seite Nr. 1
Two-Ring Door Instructions
Installation Manual
PNEG-301
Date: 01-22-08
PNEG-301
Inhaltszusammenfassung zur Seite Nr. 2
2 PNEG-301 Two-Ring Door
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Contents Chapter 1 Installation .......................................................................................................................................... 4 Two-Ring Door Installation ................................................................................................................. 4 Two-Ring Door Assembly ................................................................................................................... 6 Inner Door Auger Hood (O
Inhaltszusammenfassung zur Seite Nr. 4
1. Installation Two-Ring Door Installation Before beginning the installation, be sure the correct door has been received. Figure 1A 1. Remove inner door panels and outer door cover. Apply two rows of rope caulk around all four (4) door flanges: On vertical flanges, one row of caulk should be applied between the two vertical rows of bolts and the other row of caulk should be applied between the door frame and the first row of vertical bolts. On the horizontal flanges, a row of caulk should be
Inhaltszusammenfassung zur Seite Nr. 5
1. Installation 4. If some latch bars are loose or require excessive force to lock, loosen hex socket capscrews and adjust in or out until latch bars operate smoothly. Check that the panels are fully seated over all bearing pins. 5. Re-install outer cover. Adjust outer door hinges and latches as required. 6. Assemble door hold back as shown on Page 6. Open door cover until it approaches the bin wall. Hook retaining bracket over lower latch mount and position the door hold back against bin wal
Inhaltszusammenfassung zur Seite Nr. 6
1. Installation Two-Ring Door Assembly Figure 1B 6 PNEG-301 Two-Ring Door
Inhaltszusammenfassung zur Seite Nr. 7
1. Installation Parts List for Two-Ring Doors PART # QTY KEY 12'-27' and 30'-60' BIN DIAMETER DESCRIPTION 12'-27' and 30'-60' BIN DIAMETER 2.66" and 4.00" CORR. 1 WD-039 OUTER DOOR COVER 1 2 WD-2854 OUTER COVER LATCH BRACKET 2 3 WD-225 OUTER COVER HINGE BRACKET 2 4 WD-035 DOOR COVER BRACE SECTION 4 5 WD-033 DOOR RETAINER 3 6 WD-6124 OUTER COVER LATCH MOUNT BASE 2 7 WD-6066 OUTER COVER HINGE BASE 2 8 WD-6055 BOTTOM INNER DOOR HINGE 1 9 WD-6056 MIDDLE INNER DOOR HINGE 2 10 WD-6054 TOP INNER DOOR
Inhaltszusammenfassung zur Seite Nr. 8
1. Installation Inner Door Auger Hood (Optional) 12' (3.66 m) - 24' (7.32 m) Diameters Only Figure 1C Remove bolts, lock washers and nuts along each side of large square opening. Position auger shield as shown in Figure 1C and bolt to underside of top angle with bolt heads under shield. Replace bolts, lock washers and nuts along sides of opening. Unloading grain through door opening may cause grain bin failure if not done properly. Unloading directly through the door opening should be limite
Inhaltszusammenfassung zur Seite Nr. 9
1. Installation Door Hinge Installation Instructions Figure 1E Viewed from the Inside of the Bin During door frame and inner panel installation, install hinges in position as shown. (NOTE: Head of bolt with neoprene washer to be on the outside of the bin.) Attach hinge frame half using only existing frame to sidewall bolts. All frame to sidewall bolts must be installed. PNEG-301 Two-Ring Door
Inhaltszusammenfassung zur Seite Nr. 10
This equipment shall be installed in accordance with the current installation codes and applicable regulations which should be carefully followed in all cases. Authorities having jurisdiction should be consulted before installations are made. GSI Group 1004 E. Illinois St. Assumption, IL 62510-0020 Phone: 1-217-226-4421 Fax: 1-217-226-4420 www.gsiag.com Copyright © 2007 by GSI Group Printed in the USA
