Inhaltszusammenfassung zur Seite Nr. 1
2-347-750-11 (1)
SRP-X700P Manager
User Control Panel
Operating Instructions (Control Software Manual Ver. 1.1)
Before using the software, please read this manual and the
Operating Instructions of the Digital Powered Mixer (main unit)
thoroughly and retain it for future reference.
SRP-X700P
2002 Sony Corporation
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Features ........................................................................................................................... 3 Precautions ...................................................................................................................... 3 About This Manual......................................................................................................... 3 Installation.............................................................................
Inhaltszusammenfassung zur Seite Nr. 3
Features The CD-ROM supplied with the SRP-X700P contains two • If your computer enters the System Standby or System Hibernate applications and the driver software. state while the SRP-X700P Digital Powered Mixer is connected By installing the software in a personal computer running and these software are in use, communication between them will Windows, you can set the parameters of the SRP-X700P and can be interrupted and the software must be started again. perform from the PC the basic operatio
Inhaltszusammenfassung zur Seite Nr. 4
Installation The dedicated USB driver software is necessary to 0 Select [Search for the best driver for your device. connect the SRP-X700P Manager and User Control (Recommended).] and click [Next >]. (Fig. 3) Panel to the SRP-X700P. Installing the Dedicated USB Select Driver Software • The dedicated USB driver software is contained in the CD-ROM supplied with the SRP-X700P. • Install the dedicated USB driver software by following the instructions shown on the screen. Some computer may reboot Cli
Inhaltszusammenfassung zur Seite Nr. 5
Installing the SRP-X700P Manager Installing the User Control Panel 1 Insert the supplied CD-ROM into the CD-ROM drive of the 1 Insert the supplied CD-ROM into the CD-ROM drive of the personal computer. personal computer. Open the SRP-X700P Manager folder. Open the SRP-X700P Control folder. Double-click the Setup icon. Double-click the Setup icon. 2 The SRP-X700P Manager installation screen appears. 2 The User Control Panel installation screen appears. 3 When the screen [Welcome to the SRP-X700P
Inhaltszusammenfassung zur Seite Nr. 6
Section 1 SRP-X700P Manager The SRP-X700P Manager enables you to set all parameters of the SRP-X700P. Starting the SRP-X700P Manager If the SRP-X700P Manager is started after connecting the SRP-X700P to the personal computer with a USB cable, the present setup of the SRP-X700P is read. If the SRP-X700P Manager is started before connecting the SRP-X700P to the personal computer, the default setup of the SRP-X700P when shipped from the factory is read. If the SRP-X700P Manager is started by doubl
Inhaltszusammenfassung zur Seite Nr. 7
Edit menu (Displayed only on the INPUT and 2 Bottom menu bar OUTPUT screens) You can select the setup screen for each parameter. Copy: Copies the parameters. For the INPUT and OUTPUT buttons, submenus are displayed. 1 2 3 FRONT PANEL LOCK button You can lock the FRONT PANEL so that the buttons and faders on the SRP-X700P front panel are disabled to prevent 3 accidental operation. When locked, the FRONT PANEL LOCK button lights in red, and the LOCK indicator on the front of the SRP-X700P also lig
Inhaltszusammenfassung zur Seite Nr. 8
Names and Functions of Controls on Screen 1.1 BLOCK Screen The BLOCK screen displays the setup status and the signal level according to the internal blocks in the SRP-X700P. If you click a button, the screen jumps to the related setup screen. You can select ON/OFF and set parameters on each screen. 345678 9 qa qdqfqgqh qj qk 2 w; 1 ws wa 0q qsl 1 INPUT index qs AUTOMATIC MIXER button You can enter an index of each input channel. By entering the The AUTOMATIC MIXER button lights in green while th
Inhaltszusammenfassung zur Seite Nr. 9
1.2 INPUT Screen You can set parameters of the input block of the SRP-X700P from the INPUT screen. 1.2.1 INPUT OVERVIEW Screen This screen corresponds to the input module of the audio mixer. This screen enables you to set the following. 45 qh 1 3 2 6 qk 7 8 q; 9 qa qs qf qd qj qg 1 INPUT index 7 Setup.. button Displays the index that is input on the BLOCK screen. By clicking the Setup button, the display jumps to the INPUT EQ screen where you can set the low-cut filter, feedback 2 INPUT level me
Inhaltszusammenfassung zur Seite Nr. 10
Names and Functions of Controls on Screen qd GAIN LIMIT and qf OVER GAIN indicators INACTIVE mode: The sending level from input section is the sum of the INACTIVE mode is used to enable the INPUT fader and the qj INPUT fader and the input fader of the SRP-X700P. MASTER volume control of the SRP-X700P, and REMOTE1 If the SRP-X700P master volume is manipulated and the to 6 of the GROUP FADER screen. sound volume is remotely controlled via the REMOTE The sound volume is shown by the yellow marker t
Inhaltszusammenfassung zur Seite Nr. 11
1.2.2 INPUT EQ Screen You can set the low-cut filter, feedback reducer and parametric equalizer of the SRP-X700P input block from the INPUT EQ screen. 1 2 3 8 4 9 0 5 6 7 1 Channel select button 6 SETUP button Selects the INPUT channel that you want to set. Detect the howling point as follows. The selected button lights in yellow. • First, switch the FADER select to ACTIVE on the INPUT OVERVIEW screen or on the OUTPUT OVERVIEW 2 INPUT index screen. Displays the index that is input on the BLOCK s
Inhaltszusammenfassung zur Seite Nr. 12
Names and Functions of Controls on Screen Parametric Equalizer Block The MIC1/WL1, MIC2/WL2, MIC3, MIC4, MIC5/LINE1 and MIC6/LINE2 channels have a 3-band parametric equalizer, and the LINE3 and LINE4 channels have a 2-band parametric equalizer. Clicking the v or V button changes the following parameters of each band. You can also enter numerical values directly. You can change the center frequency and the GAIN by dragging the marker portion with the mouse. Q can be entered on the Q setup box
Inhaltszusammenfassung zur Seite Nr. 13
1.3 ROUTING Screen On this screen, you can set to which output channel the input signal is to be output. 4 1 2 3 1 INPUT index If the microphone input sound falls below a lower-specified Displays the INPUT channel index that is entered on the level, the gate function cuts off the microphone sound so that the background noise is reduced, howling is prevented, and BLOCK screen. clear sound quality is maintained. When larger than a certain 2 OUTPUT index volume is input again, the microphone input
Inhaltszusammenfassung zur Seite Nr. 14
Names and Functions of Controls on Screen 1.4 OUTPUT Screen You can set the parameters of the output block of the SRP-X700P from the OUTPUT screen. 1.4.1 OUTPUT OVERVIEW Screen This screen corresponds to the output module of the audio mixer. This screen enables you to set the following. The OUTPUT 1 through OUTPUT 8 correspond to the LINE OUTPUT 1 through LINE OUTPUT 8 of the main unit. wa 9w; qf qj qh qk ws wd ql 1 wh wf wg 3 2 4 5 6 7 8 0 qs qg qa qd 1 OUTPUT index to 52 m, or in 3.33-ft steps
Inhaltszusammenfassung zur Seite Nr. 15
qk REC OUT REF LEVEL selection box qf FADER select and qg OUTPUT fader You can set the reference output level for every output channel The qg OUTPUT fader has the two modes of ACTIVE and on this selection box. INACTIVE. You can select –10, –5 or 0 dBu as the REC OUT level. To switch the fader mode, click the qf FADER select. The selected mode lights in yellow. The yellow marker displayed ql REC OUT MUTING button on the side of the fader indicates the fader position that is the Mutes output signa
Inhaltszusammenfassung zur Seite Nr. 16
Names and Functions of Controls on Screen 1.4.2 OUTPUT EQ Screen You can set the equalizer of the SRP-X700P output block from the OUTPUT EQ screen. 1 2 3 4 5 6 7 5 5 6 6 7 7 8 1 Channel select button 6 Q setup box Selects the OUTPUT channel that you want to set. Set Q in the range of 0.15 to 22. The selected button lights in yellow. 7 GAIN setup box 2 OUTPUT index Set GAIN in 0.5-dB steps in the range of –15 dB to +15 dB. Displays the index that is entered on the BLOCK screen. 8 HCF (High-cut Fi
Inhaltszusammenfassung zur Seite Nr. 17
1.5 REMOTE Screen You can establish various setups of the remote terminal from the REMOTE screen. 1 2 3 4 6 qa qf q; 5 qs qd 8 9 7 PARALLEL I/O Block MACHINE CONTROL Block You can establish various setups to control Sony products through 1 PARALLEL INPUT indicator Displays the status of the parallel input terminal. the Control-S output terminal. For details of the connection and The PARALLEL INPUT indicator lights when the parallel other procedures, refer to “How to Control AV Equipment from the
Inhaltszusammenfassung zur Seite Nr. 18
Names and Functions of Controls on Screen qd SIGNAL DEFINE setup box PROJECTOR CONTROL Block Select the video signal format for each channel of the LINE 4 You can establish various setups to control a projector, refer to input, that is sent to projector. “How to Control the Display from the SRP-X700P” of the SRP- • LINE4A to LINE4C: You can select VIDEO, S-VIDEO or LAN. X700P Operating Instruction. • LINE4D to LINE4F: You can select RGB, COMPONENT or LAN. q; I/F TYPE When you select LAN, the LAN
Inhaltszusammenfassung zur Seite Nr. 19
Parameters in the PARALLEL INPUT FUNCTION setup box Function Parameter NONE: Does not set any function. ————— AV SEL: Selects the LINE4 input. A: Selects A. to F: Selects F. OFF: Enters the off state. LVL+: Increases the sound volume with an external switch. Mic1: Selects Mic1. LVL–: Decreases the sound volume with an external switch. to LVL: Adjusts the sound volume with an external sound volume controller. Mic4: Selects Mic4. Muting: Performs muting. Mic5Line1: Selects Mic5/Line1. Mic6Line2: S
Inhaltszusammenfassung zur Seite Nr. 20
Names and Functions of Controls on Screen USER DEFINE Screen Use this screen to set the communication protocol when USER DEFINE is selected in the PROJECTOR PROTOCOL setup box. When USER DEFINE is selected, the projector is connected to the PROJECTOR CONTROL RS-232C terminal. Once the communication protocol between the SRP-X700P and projector has been set, the projectors not supported by default can be connected. Note The above-described setup does not guarantee operation of all projectors. 1 3
