Inhaltszusammenfassung zur Seite Nr. 1
SUMMARY MANUAL
VCC-HD4600
VCC-HD4600P
Megapixel Camera
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED
SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL
CODES.
Please read this instruction manual carefully in order to ensure correct installation.
In addition, be sure to read carefully the electronic manual (INSTRUCTION MANUAL)
contained in the supplied CD-ROM to ensure correct operation of the camera.
Deutsch Español Français English
Inhaltszusammenfassung zur Seite Nr. 2
Contents Name and Function of Each Component .................................................................2 Basic Connections ....................................................................................................6 Network Settings ......................................................................................................9 Specifications ......................................................................................................... 11 Copyright Notice ......
Inhaltszusammenfassung zur Seite Nr. 3
Name and Function of Each Component ■ Rear Face Power Indicator (POWER) This indicator lights up when the camera is powered on. When the camera is on, this indicator blinks to indicate the following camera statuses: Firmware update in progress Deactivation of media recording is in progress. Error occurring on SD memory card or external hard disk drive (faster blink) 24 VAC/ 12 VDC Power Connector Terminal Connect a 24 VAC or 12 VDC power supply to this terminal using the sup
Inhaltszusammenfassung zur Seite Nr. 4
Name and Function of Each Component SD (SDHC) Card Slot When recording live video onto an SD memory card, insert the card into the slot. For details, refer to “Installing and formatting recording media” section on the electronic manual. LAN Connector (RJ-45) Use this socket to connect the camera to your PC to enable network operation. For details, refer to the “Basic Connections” ( Page 6) section. Link access indicator (Green): This indicator lights up approx. 3 seconds after power o
Inhaltszusammenfassung zur Seite Nr. 5
Name and Function of Each Component ■ Side Face Operation Buttons When using operation buttons on the camera, slide and open the side cover to access the buttons. Some operations can be performed via network operation. Basic operations (focus adjustment, zoom, etc.) Adjusting focus: Press the button to set the focus to a near target; press the button to set the focus to a far target. Live screen control panel Zoom: Press the button to zoom out of the image; press the button to
Inhaltszusammenfassung zur Seite Nr. 6
Name and Function of Each Component Resuming recording/Recognizing the recording medium: Press the and SET buttons simultaneously. The power indicator starts blinking and then stay lit after the camera recognizes the recording medium and is ready for recording. SD/HDD SETTINGS Resetting the login password (for default users only): Press the and buttons simultaneously. Not supported via network operation Power indicator The indicator also works as an error indicator. Power indicato
Inhaltszusammenfassung zur Seite Nr. 7
Basic Connections High-definition monitor Monitor Target 24 VAC GND ~ ~ 24 VAC PC 12 VDC - + 12 VDC Power Connection Attach the supplied power connecter into the power terminal. Loosen the screws on the side face of the connecter, connect the power cables to it, and tighten the screws. Connection method depends on the power supply (24 VAC or 12 VDC). Connection to 24 VAC power supply: Although the power terminals have no polarity, the earth grounding wire must be connected to the COM (GND
Inhaltszusammenfassung zur Seite Nr. 8
Basic Connections High-Definition Monitor Connection Connect the HDMI cable to the HD video output terminal (HDMI). You cannot output the video simultaneously from HD video output terminal (HDMI) and from monitor output terminal (MONITOR OUT). When both terminals are used, the HD video output terminal takes precedence. Monitor connection for video adjustment Connect the coaxial cable to the SD video output terminal (MONITOR OUT). Network Connection This camera is designed so that you can u
Inhaltszusammenfassung zur Seite Nr. 9
Basic Connections Day/Night switching Normally, switching the camera between the color and black-and-white video modes is automatically accomplished by the Day/Night function. Using one of these alarm input terminals as the Day/Night switching terminal, however, enables the camera to be switched between the color and black-and- white video modes when an external control signal is received. To use the alarm input terminals as Day/Night switching terminals, follow the steps below. • Under
Inhaltszusammenfassung zur Seite Nr. 10
Network Settings Preparing Your Computer for Network Operation Check your operating environment. ( Page 1) Connect the camera to the network to which your PC is also connected. Configue the network information on your PC. Configure information such as the IP address of your PC. Install the “H.264 Plug-in” from the supplied CD-ROM onto your PC. You are now ready to monitor the surveillance video in the H.264 format. Start Internet Explorer. The supported Web browser is Internet Explorer Ver
Inhaltszusammenfassung zur Seite Nr. 11
Network Settings Type your user name and password and click [OK]. The language selection screen appears. If this is the first access to the camera, log in as an admin user (administrator) using the following default authentication information. User name: admin Password: admin Click the button corresponding to the language you want to use. The live screen appears. From the second login onwards, the live screen appears automatically by skipping the language selection screen. If this is the
Inhaltszusammenfassung zur Seite Nr. 12
Specifications ■ Camera Image pickup device 1/2.5" CMOS sensor Effective pixels 16:9 1920 (H) × 1080 (V), 4:3 2288 (H) × 1712 (V) Lowest image illumination 50IRE: 2.0 lx (F1.8, in color mode with high gain) 50IRE: 0.1 lx (F1.8 in black-and-white mode with high gain) Video S/N ratio 50 dB or higher (when AGC is “Off”) Lens Focal Length: 6.3 to 63 mm, F number: F1.8 - 2.5 Optical zoom 10x, electronic zoom 16x (up to 160x when used in combination with the optical zoom) Digital PTZ Enables electron
Inhaltszusammenfassung zur Seite Nr. 13
Specifications ■ Network Image/video compression H.264/JPEG Video size (H.264) (16:9) 1920×1080, 1280×720, 640×360, 320×180 (4:3) 1600×1200, 1280×960, 1024×768, 640×480, 320×240 Video size (JPEG) (16:9) 1920×1080, 1280×720, 1024×576, 640×360 (4:3) 2288×1712, 1600×1200, 1280×960, 1024×768, 800×600, 640×480, 320×240 Picture quality QUALITY mode: BASIC, NORMAL, ENHANCED, FINE, SUPER FINE BITRATE mode: User-specified bit rate Interface 10BASE-T/100BASE-TX Protocol TCP/IP, UDP, HTTP, HTTPS, SMTP, N
Inhaltszusammenfassung zur Seite Nr. 14
Copyright Notice The instruction manual and the software are copyrighted by SANYO Electric Co., Ltd. No materials contained in the manual and the software may, wholly or partially, be copied, modified, reproduced, or distributed in any format without the prior permission of the copyright holder. Microsoft, Windows, ActiveX and Internet Explorer are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. ® ® The official name for “Windows” used i
Inhaltszusammenfassung zur Seite Nr. 15
SANYO Electric Co., Ltd. 1AC6P1P4038-- L5DH2/XE, US, JP (1009KR)
