Inhaltszusammenfassung zur Seite Nr. 1
LevelOne
FCS-1050
Day/Night IP Network Camera
User’s Manual
Inhaltszusammenfassung zur Seite Nr. 2
Before You Use This Product The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but also can be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the list in the "Package Contents
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Before You Use This Product......................................................................1 Table of Contents Package Contents ...........................................................2 Package Contents....................................................................................3 Installation.............................................................................................5 Hardware installation.....................................
Inhaltszusammenfassung zur Seite Nr. 4
Package Contents Network Camera FCS-1050 Camera stand Power adapter Software CD I/O terminal block connector - 3 -
Inhaltszusammenfassung zur Seite Nr. 5
Installation Hardware installation Please verify that your product package contains all the accessories listed in the foregoing Package Contents. Depending on the user’s application, an Ethernet cable may be needed. The Ethernet cable should meet the specs of UTP Category 5 and not exceed 100 meters in length. Connect the power adapter jack to the Network Camera before plugging in to the power socket. This will reduce the risk of accidental electric shock. Upon powering
Inhaltszusammenfassung zur Seite Nr. 6
Software installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to the person who can configure the Network Camera and grant user access to the camera. At the end of the hardware installation, users can use Installation wizard included in the product CDROM to find the location of the Network Camera. There may be many Network Cameras in the local network. Users can differentiate the Network Cameras with the MAC Ad
Inhaltszusammenfassung zur Seite Nr. 7
If users run Installation wizard before the hardware installation, the Network Camera may not be showed on the Installer list. After the hardware installation, users may click on to update the list. Users may click directly on to access the Network Camera in the default browser. Once installation is complete, the Administrator should proceed to the next section "Initial access to the Network Camera" for necessary checks and con
Inhaltszusammenfassung zur Seite Nr. 8
Initial Access to the Network Camera Check Network Settings The Network Camera can be connected either before or immediately after software installation onto the Local Area Network. The Administrator should complete the network settings on the configuration page, including the correct subnet mask and IP address of gateway and DNS. Ask your network administrator or Internet service provider for the detail information. By default the Network Camera requires the Administrator to
Inhaltszusammenfassung zur Seite Nr. 9
How to Use Authentication After opening the Web browser and typing in the URL of the Network Camera, a dialogue window pops up to request a username and password. Upon successful authentication, the following figure is displayed. The foreground is the login window and the background shows the message if authentication fails. The user may check the option box to save the password for future convenience. This option is not available to the Administrator for obvious reason.
Inhaltszusammenfassung zur Seite Nr. 10
This plug-in has been registered for certificate and is used to display the video in the browser. Users may click on to proceed. If the web browser does not allow the user to continue to install, check the Internet security option to lower the security levels or contact your IT or networking supervisor for help. - 10 -
Inhaltszusammenfassung zur Seite Nr. 11
Primary user’s capability Main screen with camera view The main page layout has two parts: Configuration functions: The camera can be configured using these user interfaces. Camera View: What the camera sees. Click the configuration link on the left menu to enter the configuration page. - 11 -
Inhaltszusammenfassung zur Seite Nr. 12
Digital Zoom Click on the magnifier icon under the camera view then the digital zoom control panel will be shown. Uncheck “Disable digital zoom” and use the slider control to change the zoom factors. Digital Output Clicking on the “On” or “Off” button turns the digital output to either on or off status. Snapshot Click on , web browser will pop up a new window to show the snapshot. Users can point at the snapshot and click the right button of mouse to save it. - 12 -
Inhaltszusammenfassung zur Seite Nr. 13
Client settings At the initial access to the “Connection type” page in Windows, the web browser will ask for a new plug-in installation, the plug-in being the Network Camera. This plug-in has been registered for certification and can be used to change the parameters at the client’s site. The user may click on to install the plug-in. If the web browser does not allow the user to complete the installation, check the Internet security to lower the security level or contact your
Inhaltszusammenfassung zur Seite Nr. 14
UDP protocol. The HTTP protocol must be selected if the network is protected by a firewall and it only allows HTTP Port (80) to be opened. In this mode, audio will not be sent and only video is operational. If no special need is required, UDP protocol is recommended. Generally speaking, the client’s choice will be in the order of UDP → TCP → HTTP. After the Network Camera is connected successfully, “Protocol Option” will indicate the selected protocol. The selected protocol w
Inhaltszusammenfassung zur Seite Nr. 15
Administrator’s capability Fine-tuning for Best Performance Best performance generally equates to the fastest image refresh rate with the best video quality, and at the lowest network bandwidth as possible. The three factors, “Maximum frame rate”, “Fix bit rate”, and “Fix quality” on the Video Configuration page, are correlative to allow for achieving the best performance possible. For Best Real-time Video Images To achieve good real-time visual effect, the network band
Inhaltszusammenfassung zur Seite Nr. 16
broadband network is over 1 Mbps, set the “Fix bit rate” to 1000Kbps or 1200Kbps, and set “Fix quality” at the highest quality. The maximum frame rate is 25 in PAL system and 30 in NTSC system. If your network bandwidth is more than 384Kbps, you can fix the bit rate according to your bandwidth and set the maximum frame rate to 25 fps or 30 fps. If the images vary dramatically in your environment, you may want to slow the maximum frame rate down to 20 fps in order to lower the r
Inhaltszusammenfassung zur Seite Nr. 17
Opening accounts for new users Protect Network Camera by passwords The Network Camera is shipped without any password by default. That means everyone can access the Network Camera including the configuration as long as the IP address is known. It is necessary to assign a password if the Network Camera is 1 intended to be accessed by others. Type a new word twice in ○ to enable protection. This password is used to identify the administrator. Then add an account with user 2
Inhaltszusammenfassung zur Seite Nr. 18
3 users from ○. 4 More flexible options for viewers ○ The first option allows anyone uses “demo” as the user name to view without password. The Administrator can also decide if more viewers are allowed to watch the video if the viewers exceed the limit. The overloaded viewers will have snapshot mode instead. Change homepage layout How to change the font color 1. Click on “Configuration” on homepage, 2. Click on “Homepage layout” at the left colum
Inhaltszusammenfassung zur Seite Nr. 19
If you want to display simple color without any image, 3. Find “Background graph” and choose “blank”, 4. Find “Background color” and pull down the list to choose any color you like, 5. Click on “Save” button. * The background color is better to contrast with the font. If you want to use the image from another web site as background, 3. Find “Background graph” and choose “Url”, 4. Type the URL of the image on the Internet in the edit box, for example, “http://dgl.micros
Inhaltszusammenfassung zur Seite Nr. 20
4. Type the URL of the image on the Internet in the edit box, for example, “http://dgl.microsoft.com/thumbnails/j023/j0234430(t).gif”, 5. Click on “Save” button. If you want to change the default logo stored in the Network Camera, 3. Find “Logo graph” and choose “default”, 4. Click on “Save” button, 5. Prepare an image file with size less than 65000 bytes and rename it to logo.gif, 6. Open an FTP client program and connect to the Network Camera. The user name and password
