Inhaltszusammenfassung zur Seite Nr. 1
SERVICE MANUAL
MULTIFUNCTIONAL DIGITAL SYSTEMS
e-STUDIO350/450
e-STUDIO352/452
e-STUDIO353/453
Model: DP-3520/3540/4520/4540
Publish Date: November 2003
File No. SME030028I0
R03092140702-TTEC
Ver09_2008-04
Inhaltszusammenfassung zur Seite Nr. 2
Trademarks • The official name of Windows 95 is Microsoft Windows 95 Operating System. • The official name of Windows 98 is Microsoft Windows 98 Operating System. • The official name of Windows Me is Microsoft Windows Millennium Edition Operating System. • The official name of Windows 2000 is Microsoft Windows 2000 Operating System. • The official name of Windows XP is Microsoft Windows XP Operating System. • Microsoft, Windows, Windows NT and the brand names and product names of other Microsoft
Inhaltszusammenfassung zur Seite Nr. 3
GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND SERVICE FOR e-STUDIO350/352/353/450/452/453 The installation and service should be done by a qualified service technician. 1. Transportation / Installation • When transporting/installing the equipment, employ two persons and be sure to use the positions as indicated below. The equipment is quite heavy and weighs approximately 83kg (182.98 lb.): e-STUDIO350/450 / 86kg (189.59 lb): e-STUDIO352/353/452/453 therefore pay full attention when ha
Inhaltszusammenfassung zur Seite Nr. 4
• Use suitable measuring instrumentsand tools. • Avoid exposure tolaser radiation during servicing. - Avoid direct exposure to the beam. - Do not insert tools, parts, etc. that are reflective into the path of the laser beam. - Remove all watches, rings, bracelets, etc. that are reflective. • Unplug the power cable and cleanthe area around the prongsof the plug oncea year ormore. A fire may occur when dust lies on this area. 3. Main Service Parts for Safety • The
Inhaltszusammenfassung zur Seite Nr. 5
CONTENTS 1. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES ....................................1-1 1.1 Specifications .......................................................................................................................1-1 1.2 Accessories ..........................................................................................................................1-5 1.3 Options .................................................................................................
Inhaltszusammenfassung zur Seite Nr. 6
4.4 Flow Chart ..........................................................................................................................4-12 4.4.1 Immediately afterthe power is turned ON ..............................................................4-12 4.4.2 Automatic paper feed copying ................................................................................4-14 5. CONTROL PANEL .................................................................................................
Inhaltszusammenfassung zur Seite Nr. 7
8. LASER OPTICAL UNIT .................................................................................................8-1 8.1 General Description .............................................................................................................8-1 8.2 Structure ...............................................................................................................................8-3 8.3 Laser Diode ........................................................................
Inhaltszusammenfassung zur Seite Nr. 8
12.4 Auto-Toner Circuit ..............................................................................................................12-4 12.4.1 General description .................................................................................................12-4 12.4.2 Function of auto-toner sensor .................................................................................12-5 12.4.3 Adjustment using the temperature / humidity sensor ..............................................
Inhaltszusammenfassung zur Seite Nr. 9
1. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 1.1 Specifications V alues in [ ] are for e-STUDIO450/452/453 in case that the specification is dif ferent between e-STUDIO350/352/353 and e-STUDIO450/452/453. •Copy process Indirect electrophotographic process (dry) • Type Desktop type (console type: when paper feed pedestal (PFP) and large ca- pacity feeder (LCF)are installed) • Originaltable Fixed type (the left rear cornerused as guide to place origi
Inhaltszusammenfassung zur Seite Nr. 10
* System copy speed 1 Sec. Copy mode e-STUDIO e-STUDIO * The system copy speed,including 350/352/353 450/452/453 scanning time, isavailable when Single-sided originals 1 set 20.85 17.49 10 sheets of A4/LT size originalare ↓ 3 sets 57.95 46.68 set on RADFand one of the copy Single-sidedcopies 5sets 91.20 73.50 modesin the left tableis selected. Single-sided originals 1set 27.42 25.71 Theperiod of time from pressing ↓ 3 sets 62.18 57.41 [START] tothe
Inhaltszusammenfassung zur Seite Nr. 11
•Eliminated portion ............. Leading edges :3.0±2.0 mm, Side/trailing edges : 2.0±2.0 mm(copy) 1 Leading/ trailing edges : 5.0±2.0mm, Side edges : 5.0±2.0 mm(print) •Paper feeding .................... Automatic feeding : Standard drawers–2 drawers (stack height 60.5 mm, 2 equivalent to 550 sheets; 64 to 80 g/m (17 to 22 lb.)) PFP–Option (One drawer or two : stack height 60.5 mm, 2 equivalent to 550 sheets; 64 to 80 g/m (1
Inhaltszusammenfassung zur Seite Nr. 12
• Dimensions of the equipment ....... See the figure below 1 W660 x D718x H739 mm (e-STUDIO350/450) W660x D758 x H739 mm (e-STUDIO352/353/452/453) * Whenthe tilt angle of thecontrol panel is 45degrees. D 45˚ H W Fig. 1-101 e-STUDIO350/352/353/450/452/453 1- 4 © 2003 - 2008 TOSHIBA TEC CORPORATION All rights reserved SPECIFICATIONS 07/11
Inhaltszusammenfassung zur Seite Nr. 13
1.2 Accessories 1 Unpacking/setup instruction 1 set Operator’s manual 4pcs. (except for MJD) Operator's manual pocket 1 pc. Power cable 1 pc. Warranty sheet 1 pc. (forNAD) Setup report 1 set(for NAD and MJD) Customersatisfaction card 1 pc. (forMJD) PM sticker 1 pc. (forMJD) Drum (installedinside ofthe equipment) 1 pc. Toner bag 1 pc. Toner cartridge 1pc. (except for NAD, MJD) Developer material 1 pc. (exceptfor NAD,MJD) Operation panel stopper 1 pc. Blind s
Inhaltszusammenfassung zur Seite Nr. 14
1.3 Options 1 1.3.1 e-STUDIO350/450 Platen Cover KA-3511 PC/PC-C Reversing Automatic DocumentFeeder (RADF) MR-3015 Drawer Module MY-1021/-C PaperFeed Pedestal (PFP) KD-1011 /-C Large Capacity Feeder(LCF) KD-1012 A4/LT/A4-C Finisher (Hanging type) MJ-1022 /-C Finisher (Console type) MJ-1023/-C Finisher (Console saddle stitcher type) MJ-1024/-C Hole Punch Unit MJ-6004 N/E/F/S *1 STAPLE-1600(for MJ-1022) Staple Cartridge STAPLE-2000 (for MJ-1023/1024) STAPLE-600 (for MJ-102
Inhaltszusammenfassung zur Seite Nr. 15
1.3.2 e-STUDIO352/353/452/453 1 Platen cover KA-3511PC Reversing Automatic DocumentFeeder (RADF) MR-3018 Drawer module MY-1021/-C Paper Feed Pedestal (PFP) KD-1011/-C Large CapacityFeeder (LCF) KD-1012LT/A4/A4-C Finisher (Hangingtype) : e-STUDIO352/353 only MJ-1022/-C Finisher (Consoletype) MJ-1101 Finisher (Console type) MJ-1023/-C Finisher (Consolesaddle stitcher type) MJ-1024/-C Hole punchunit (forMJ-1 101) MJ-6101N/E/F/S Hole punch unit (forMJ-1023/1024) MJ-6004N/
Inhaltszusammenfassung zur Seite Nr. 16
Notes: 1 1. T h e b r i d g e k i t ( K N - 3 5 2 0 ) i s n e c e s s a r y f o r i n s t a l l a t i o n o f t h e fi n i s h e r ( M J - 1 0 2 2 , M J - 1 0 2 3 / 1 0 2 4 orMJ-1 101). 2. The finisher (MJ-1023/1024) is necessary for installation of the hole punch unit (MJ-6004N/ E / F / S ) . T h e fi n i s h e r ( M J - 1 1 0 1 ) i s n e c e s s a r y f o r i n s t a l l a t i o n o f t h e h o l e p u n c h u n i t ( M J -
Inhaltszusammenfassung zur Seite Nr. 17
1.4 Supplies 1 Drum OD-3500 Tonerbag PS-TB3520/E/N *2 PS-ZT3520 /T/D/C/E *3 (e-STUDIO350/352/450/452 ) Tonercartridge PS-ZT3520C *3, PS-ZT4520/E *3 (e-STUDIO353/453 ) Developer D-3500 * 2) N : Asia E : Europe NONE : North America * 3) T : Taiwan D : Asia C :China E : Europe NONE :North America © 2003- 2008 TOSHIBA TECCORPORA TION All rightsreserved 1- 9 e-STUDIO350/352/353/450/452/453 SPECIFICATIONS 07/11
Inhaltszusammenfassung zur Seite Nr. 18
1.5 System List 1 1.5.1 e-STUDIO350/450 Fig. 1-501 e-STUDIO350/352/353/450/452/453 1- 10 © 2003 -2008 TOSHIBA TECCORPORA TION All rights reserved SPECIFICATIONS 05/11 Reversing Automatic Document Feeder Platen Cover ( ) RADF KA-3511 MR-3015 Finisher ( ) Hanging type MJ-1022 Work Tray KK-3511 Staple Cartridge STAPLE-1600 Key Copy Counter Bridge Kit MU-8, MU-10 KN-3520 Staple Cartridge STAPLE-2000 Damp Heater Hole Punch Unit MF-3520 U/E MJ-6004 N/E/F/S Job Separator Data MJ-5004 ove
Inhaltszusammenfassung zur Seite Nr. 19
1.5.2 e-STUDIO352/353/452/453 1 Fig. 1-502 © 2003 - 2008 TOSHIBA TEC CORPORATION All rightsreserved 1- 11 e-STUDIO350/352/353/450/452/453 SPECIFICATIONS 08/04 Reversing Automatic e-BRIDGE Finisher Document Feeder ID Gate ( ) Hanging type Platen Cover (RADF) KP-2004 MJ-1022 KA-3511 MR-3018 e-BRIDGE ID Gate Staple Cartridge KP-2005 STAPLE-1600 Work Tray KK-3511 Staple Cartridge STAPLE-2000 Wireless LAN Finisher Module (Console type) GN-1041 MJ-1023 Hole Punch Unit Bridge Kit Bluetooth MJ-
Inhaltszusammenfassung zur Seite Nr. 20
1 e-STUDIO350/352/353/450/452/453 1 - 12 © 2003 - 2008 TOSHIBA TEC CORPORATION All rights reserved SPECIFICATIONS
