Inhaltszusammenfassung zur Seite Nr. 7
Getting started Installation preparation You must install and See page 7 charge the battery before for easy instructions. STOP! using the telephone. If you subscribe to high-speed internet service (Digital Subscriber Line - DSL) through your telephone lines, you must have a DSL filter between the telephone base and the telephone wall jack (see the following page). The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for m
Inhaltszusammenfassung zur Seite Nr. 8
Getting started Telephone base & charger installation Install the telephone base as shown below. Make sure that the electrical outlet is not controlled by a wall switch. If you subscribe to high-speed internet service (Digital Subscriber Line - DSL) through your telephone lines, you must have a DSL filter between the telephone base and the telephone wall jack. The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more
Inhaltszusammenfassung zur Seite Nr. 9
Getting started Telephone base & charger installation Charger installation Plug the power adapter into an electrical outlet. IMPORTANT INFORMATION 1. Use only the power adapter(s) supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com, or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 2. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug
Inhaltszusammenfassung zur Seite Nr. 10
Getting started Battery installation & charging Install the battery as shown below. After installing the battery, you can make and receive short calls, but replace the handset in the telephone base or charger when not in use. For optimal performance, charge the handset battery for at least 16 hours before use. When fully charged, the handset battery provides approximately five hours of talk time or three days of standby time. Step 1 Step 2 Step 3 Plug the battery Insert the supplied Alig
Inhaltszusammenfassung zur Seite Nr. 11
Getting started Battery installation & charging Step 4 Charge the handset by placing it face up in the telephone base or charger. The CHARGE light will be on when charging. IMPORTANT INFORMATION Use only the supplied rechargeable battery or replacement battery (model BT8001). To order, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 8
Inhaltszusammenfassung zur Seite Nr. 12
Getting started Belt clip & optional headset Removal Pull and unlock one flap Installation from the notch first before Snap the belt clip detaching the whole belt clip into the notches from the handset. on both sides of handset. For handsfree telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results, use an AT&T 2.5 mm headset. To purchase a headset, v viis siit t o ou ur r w we eb bs siit te e a at t www.telephones.att.com or c
Inhaltszusammenfassung zur Seite Nr. 13
Getting started Mounting bracket procedure The telephone base comes with the mounting bracket installed for desktop use. Wall mounting requires a telephone outlet wall mounting plate with mounting studs that may require professional installation. You can purchase the mounting plate from many hardware or consumer electronics retailers. NOTE: The mounting bracket must be used for both tabletop and wall mounting positions. Desktop to wall mount installation To change the telephone base to the
Inhaltszusammenfassung zur Seite Nr. 14
Getting started Mounting bracket procedure Desktop to wall mount installation 3. Position your hands as shown in Figure 3. Press your thumbs down on the tabs that are below the bracket, holding it in place. Use your index fingers to move the bracket towards yourself. Figure 3. Detaching the bracket from the telephone base 4. Tilt the top of the bracket away from you until it is resting on the telephone base. 5. Align the grooves of the bracket with the upper keeper tabs on the telephone ba
Inhaltszusammenfassung zur Seite Nr. 15
Getting started Mounting bracket procedure Desktop to wall mount installation 6. Slide the bracket away from you until it clicks into the keeper tabs. Figure 5. Upper keeper tab location 7. Align the holes on the telephone base with the standard wall plate and slide the bracket until the telephone is secured as shown in Figure 6. Figure 6. Wall mount position 12
Inhaltszusammenfassung zur Seite Nr. 16
Getting started Mounting bracket procedure Desktop to wall mount installation 8. Raise the antenna. 13
Inhaltszusammenfassung zur Seite Nr. 17
Getting started Mounting bracket procedure Wall mount to desktop installation To change the telephone base to the desktop position: 1. Remove the telephone base from the wall. 2. Place the telephone base on a flat surface with the antenna on the left side as shown in Figure 7. Antenna Figure 7. Wall mounting bracket location 14
Inhaltszusammenfassung zur Seite Nr. 18
Telephone operation Mounting bracket procedure Wall mount to desktop installation 3. Maintain contact with the telephone base and slide the bracket towards you until it is free of the upper keeper tabs shown in Figure 8. Upper keeper tabs Figure 8. Upper keeper tab location 4. Tilt the top of the bracket towards you until it is resting on the telephone base. 5. A Alliig gn n t th he e g gr ro oo ov ve es s o off t th he e b br ra ac ck ke et t w wiit th h t th he e llo ow we er r k ke ee e
Inhaltszusammenfassung zur Seite Nr. 19
Telephone operation Mounting bracket procedure Wall mount to desktop installation 6. S Slliid de e t th he e b br ra ac ck ke et t a aw wa ay y ffr ro om m y yo ou u u un nt tiill iit t c clliic ck ks s iin nt to o t th he e k ke ee ep pe er r t ta ab bs s.. Figure 10. Lower keeper tab location 7. R Ro ou ut te e t th he e t te elle ep ph ho on ne e lliin ne e c co or rd d a an nd d t th he e p po ow we er r a ad da ap pt te er r t th hr ro ou ug gh h t th he e s sllo ot ts s o on n t th he e
Inhaltszusammenfassung zur Seite Nr. 20
Handset settings Handset settings Using the feature menu, you can customize many of the telephone’s settings. 1. Press MENU/SELECT when in idle mode (when >DIRECTORY the phone is not in use) to enter the feature CALL LOG menu. 2. Use DIR / CID to scroll to the feature to be changed. When scrolling through the menu, the top menu item is always highlighted with a > symbol. 3. Press MENU/SELECT to select the highlighted item. NOTE: To cancel an operation, back up to the previous
