Inhaltszusammenfassung zur Seite Nr. 1
XS1210
OWNER'S
MANUAL
OWNER'S MANUAL
Inhaltszusammenfassung zur Seite Nr. 2
Introduction Uniden 2.4GHz cordless phones are designed and engineered to exacting standards for reliability, long life, and outstanding performance. NOTE: Illustrations in this manual are used for explanation purposes. Some illustrations in this manual may differ from the actual unit. The color of your cordless phone may vary. Features • 2.4 GHz Extended Range Technology AutoTalk Tone Dialing 20 Channel Autoscan Last Number Redial 10-Number Memory Dialing AutoStandby Earpiece Volu
Inhaltszusammenfassung zur Seite Nr. 3
Included with Your Phone Base Unit Handset AC adaptor Rechargeable Battery Telephone Cord Wall Mount adaptor This owner’s manual Terminology Throughout this manual, terms such as Standby and Talk Mode are used. Below is the terminology explanation. Talk Mode - The handset is off the base and the talk key has been pressed, enabling a dial tone. Standby Mode - The handset may be sitting in or off the base, but is NOT in use. The talk key has not been pressed and there is no dial
Inhaltszusammenfassung zur Seite Nr. 4
B. Install the rechargeable battery pack into the handset The handset is powered by a rechargeable battery pack. The battery recharges automatically when the handset is placed in the base unit. NOTE: If your home has specially wired alarm equipment connected to the telephone line, be sure that installing the system does not disable your alarm equipment. If you have questions about what will disable your alarm equipment, contact your telephone company or a qualified installer. 1. Press down on th
Inhaltszusammenfassung zur Seite Nr. 5
5. Once the handset battery pack is fully charged, connect the telephone line cord to the TEL LINE jack and a telephone outlet. Australia Tel Line Adaptor (Not supplied) D. Mount the base unit on a wall Standard wall plate mounting This phone can be mounted on any standard wall plate. 2 1. Locate the base unit on the wall mount adaptor 5 as shown and slide the wall mount adaptor into the notches on the base bottom with the tab pressed. 2. Plug the AC adaptor into the DC IN 9V jack. 3. Route the
Inhaltszusammenfassung zur Seite Nr. 6
Making and Receiving Calls Making a call 1. Remove the handset from the base. 2. Press the talk key. The talk/batt low LED flashes and turns on. 3. Listen for the dial tone. 4. Dial the number. Receiving a call If the handset is in the base, simply remove the handset from the base. AutoTalk will automatically answer the call. If the handset is off the base, press the talk key or any number key. Hanging up Press the end key or return the handset to the base. Redialing the last dialed number 1. Re
Inhaltszusammenfassung zur Seite Nr. 7
Find Handset To locate the handset, press the find handset key on the base. The handset beeps for 60 seconds. The handset stops beeping when any key is pressed, when it is returned to the base, or when the find handset key is pressed. The handset also stops beeping when an incoming call is received. Low Battery Alert When the battery pack is very low and needs to be charged, the phone is programmed to eliminate functions in order to save power. If the phone is not in use, the talk/batt low LED f
Inhaltszusammenfassung zur Seite Nr. 8
3. If you need the phone to pause during the dialing sequence, press the redial/pause key to insert a two-second delay between the numbers. You can enter multiple pauses to increase the delay. Each pause counts as a digit. 4. Press the memory key again. 5. To store this number in the RocketDial memory, press the Rocketdial/call wait key. You will hear a confirmation tone indicating that the number has been stored. 6. To store this number as one of the ten speed dial numbers, enter a digit from 0
Inhaltszusammenfassung zur Seite Nr. 9
Changing the Digital Security Code The digital security code is an identification code used to connect the handset and the base unit. Normally, setting the code is not necessary. The first time you charge your handset, the security code is automatically set. In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code. 1. Remove the handset from the base unit. Press and hold the find handset key on the base. 2. While holding the find
Inhaltszusammenfassung zur Seite Nr. 10
Troubleshooting If your cordless telephone is not performing to your expectations, please try these simple steps first. If these steps do not solve your problem, please visit our website www.uniden.co.au or www.uniden.co.nz NOTE: Do not attempt to service this unit yourself. Servicing must be performed by qualified personnel. Symptom Suggestion The charge/in use LED won’t Make sure the AC adaptor is plugged into the base and a wall illuminate when the handset is outlet. placed in the base. M
Inhaltszusammenfassung zur Seite Nr. 11
Warranty UNIDEN XS1210 Cordless Phone Limited One Year Warranty Note: Please keep your sales docket as it provides evidence of warranty. Warrantor: Uniden Australia Pty Limited ABN 58 001 865 498 Uniden New Zealand Lmited Warranty only available in original country of purchase Elements of Warranty: Uniden warrants to the original retail owner for the duration of this warranty, its XS1210 Cordless Phone (hereinafter referred to as the Product) to be free from defects in materials and craftsmanshi
Inhaltszusammenfassung zur Seite Nr. 12
© 2005 Uniden Australia Pty Limited/Uniden New Zealand Limited Printed in China UPZZ01059ZZ
